analog devices wing guide

adafruitio-temp-motion-wing/adafruit-io-adt7410-adxl343.ino

@@ -0,0 +1,143 @@
+// Adafruit IO - Analog Devices ADT7410 + ADXL343 Example
+//
+// Adafruit invests time and resources providing this open source code.
+// Please support Adafruit and open source hardware by purchasing
+// products from Adafruit!
+//
+// Written by Brent Rubell for Adafruit Industries
+// Copyright (c) 2019 Adafruit Industries
+// Licensed under the MIT license.
+//
+// All text above must be included in any redistribution.
+
+/************************ Adafruit IO Config *******************************/
+// visit io.adafruit.com if you need to create an account,
+// or if you need your Adafruit IO key.
+#define IO_USERNAME "YOUR_IO_USERNAME"
+#define IO_KEY "YOUR_IO_KEY"
+
+/******************************* WiFi Config ********************************/
+#define WIFI_SSID "WIFI_NAME"
+#define WIFI_PASS "WIFI_PASS"
+
+// comment out the following two lines if you are using fona or ethernet
+#include "AdafruitIO_WiFi.h"
+AdafruitIO_WiFi io(IO_USERNAME, IO_KEY, WIFI_SSID, WIFI_PASS);
+
+/************************** Configuration ***********************************/
+// time between sending data to adafruit io, in seconds.
+#define IO_DELAY 5
+/************************ Example Starts Here *******************************/
+#include <Wire.h>
+#include <Adafruit_Sensor.h>
+#include "Adafruit_ADT7410.h"
+#include <Adafruit_ADXL343.h>
+
+float tempC, accelX, accelY, accelZ;
+
+// Create the ADT7410 temperature sensor object
+Adafruit_ADT7410 tempsensor = Adafruit_ADT7410();
+
+// Create the ADXL343 accelerometer sensor object
+Adafruit_ADXL343 accel = Adafruit_ADXL343(12345);
+
+// set up the 'temperature' feed
+AdafruitIO_Feed *huzzah_temperature = io.feed("temperature");
+
+// set up the 'accelX' feed
+AdafruitIO_Feed *huzzah_accel_x = io.feed("accelX");
+
+// set up the 'accelY' feed
+AdafruitIO_Feed *huzzah_accel_y = io.feed("accelY");
+
+// set up the 'accelZ' feed
+AdafruitIO_Feed *huzzah_accel_z= io.feed("accelZ");
+
+void setup()
+{
+  // start the serial connection
+  Serial.begin(115200);
+
+  // wait for serial monitor to open
+  while (!Serial)
+    ;
+
+  Serial.println("Adafruit IO - ADT7410 + ADX343");
+
+  /* Initialise the ADXL343 */
+  if(!accel.begin())
+  {
+    /* There was a problem detecting the ADXL343 ... check your connections */
+    Serial.println("Ooops, no ADXL343 detected ... Check your wiring!");
+    while(1);
+  }
+
+  /* Set the range to whatever is appropriate for your project */
+  accel.setRange(ADXL343_RANGE_16_G);
+
+  /* Initialise the ADT7410 */
+  if (!tempsensor.begin())
+  {
+    Serial.println("Couldn't find ADT7410!");
+    while (1)
+      ;
+  }
+
+  // sensor takes 250 ms to get first readings
+  delay(250);
+
+  // connect to io.adafruit.com
+  Serial.print("Connecting to Adafruit IO");
+  io.connect();
+
+  // wait for a connection
+  while (io.status() < AIO_CONNECTED)
+  {
+    Serial.print(".");
+    delay(500);
+  }
+
+  // we are connected
+  Serial.println();
+  Serial.println(io.statusText());
+}
+
+void loop()
+{
+  // io.run(); is required for all sketches.
+  // it should always be present at the top of your loop
+  // function. it keeps the client connected to
+  // io.adafruit.com, and processes any incoming data.
+  io.run();
+
+   /* Get a new accel. sensor event */
+  sensors_event_t event;
+  accel.getEvent(&event);
+
+  accelX = event.acceleration.x;
+  accelY = event.acceleration.y;
+  accelZ = event.acceleration.z;
+
+  /* Display the results (acceleration is measured in m/s^2) */
+  Serial.print("X: "); Serial.print(accelX); Serial.print("  ");
+  Serial.print("Y: "); Serial.print(accelY); Serial.print("  ");
+  Serial.print("Z: "); Serial.print(accelZ); Serial.print("  ");Serial.println("m/s^2 ");
+  
+  // Read and print out the temperature
+  tempC = tempsensor.readTempC();
+  Serial.print("Temperature: "); Serial.print(tempC); Serial.println("C");
+
+  Serial.println("Sending to Adafruit IO...");
+  huzzah_temperature->save(tempC, 0, 0, 0, 2);
+  huzzah_accel_x->save(accelX);
+  huzzah_accel_y->save(accelY);
+  huzzah_accel_z->save(accelZ);
+  Serial.println("Data sent!");
+
+  Serial.print("Waiting ");Serial.print(IO_DELAY);Serial.println(" seconds...");
+  // wait IO_DELAY seconds between sends
+  for (int i = 0; i < IO_DELAY; i++)
+  {
+    delay(1000);
+  }
+}