147 lines
4.2 KiB
C++
147 lines
4.2 KiB
C++
// SPDX-FileCopyrightText: 2019 Brent Rubell for Adafruit Industries
|
|
//
|
|
// SPDX-License-Identifier: MIT
|
|
|
|
// Adafruit IO - Analog Devices ADT7410 + ADXL343 Example
|
|
//
|
|
// Adafruit invests time and resources providing this open source code.
|
|
// Please support Adafruit and open source hardware by purchasing
|
|
// products from Adafruit!
|
|
//
|
|
// Written by Brent Rubell for Adafruit Industries
|
|
// Copyright (c) 2019 Adafruit Industries
|
|
// Licensed under the MIT license.
|
|
//
|
|
// All text above must be included in any redistribution.
|
|
|
|
/************************ Adafruit IO Config *******************************/
|
|
// visit io.adafruit.com if you need to create an account,
|
|
// or if you need your Adafruit IO key.
|
|
#define IO_USERNAME "YOUR_IO_USERNAME"
|
|
#define IO_KEY "YOUR_IO_KEY"
|
|
|
|
/******************************* WiFi Config ********************************/
|
|
#define WIFI_SSID "WIFI_NAME"
|
|
#define WIFI_PASS "WIFI_PASS"
|
|
|
|
// comment out the following two lines if you are using fona or ethernet
|
|
#include "AdafruitIO_WiFi.h"
|
|
AdafruitIO_WiFi io(IO_USERNAME, IO_KEY, WIFI_SSID, WIFI_PASS);
|
|
|
|
/************************** Configuration ***********************************/
|
|
// time between sending data to adafruit io, in seconds.
|
|
#define IO_DELAY 5
|
|
/************************ Example Starts Here *******************************/
|
|
#include <Wire.h>
|
|
#include <Adafruit_Sensor.h>
|
|
#include "Adafruit_ADT7410.h"
|
|
#include <Adafruit_ADXL343.h>
|
|
|
|
float tempC, accelX, accelY, accelZ;
|
|
|
|
// Create the ADT7410 temperature sensor object
|
|
Adafruit_ADT7410 tempsensor = Adafruit_ADT7410();
|
|
|
|
// Create the ADXL343 accelerometer sensor object
|
|
Adafruit_ADXL343 accel = Adafruit_ADXL343(12345);
|
|
|
|
// set up the 'temperature' feed
|
|
AdafruitIO_Feed *huzzah_temperature = io.feed("temperature");
|
|
|
|
// set up the 'accelX' feed
|
|
AdafruitIO_Feed *huzzah_accel_x = io.feed("accelX");
|
|
|
|
// set up the 'accelY' feed
|
|
AdafruitIO_Feed *huzzah_accel_y = io.feed("accelY");
|
|
|
|
// set up the 'accelZ' feed
|
|
AdafruitIO_Feed *huzzah_accel_z= io.feed("accelZ");
|
|
|
|
void setup()
|
|
{
|
|
// start the serial connection
|
|
Serial.begin(115200);
|
|
|
|
// wait for serial monitor to open
|
|
while (!Serial)
|
|
;
|
|
|
|
Serial.println("Adafruit IO - ADT7410 + ADX343");
|
|
|
|
/* Initialise the ADXL343 */
|
|
if(!accel.begin())
|
|
{
|
|
/* There was a problem detecting the ADXL343 ... check your connections */
|
|
Serial.println("Ooops, no ADXL343 detected ... Check your wiring!");
|
|
while(1);
|
|
}
|
|
|
|
/* Set the range to whatever is appropriate for your project */
|
|
accel.setRange(ADXL343_RANGE_16_G);
|
|
|
|
/* Initialise the ADT7410 */
|
|
if (!tempsensor.begin())
|
|
{
|
|
Serial.println("Couldn't find ADT7410!");
|
|
while (1)
|
|
;
|
|
}
|
|
|
|
// sensor takes 250 ms to get first readings
|
|
delay(250);
|
|
|
|
// connect to io.adafruit.com
|
|
Serial.print("Connecting to Adafruit IO");
|
|
io.connect();
|
|
|
|
// wait for a connection
|
|
while (io.status() < AIO_CONNECTED)
|
|
{
|
|
Serial.print(".");
|
|
delay(500);
|
|
}
|
|
|
|
// we are connected
|
|
Serial.println();
|
|
Serial.println(io.statusText());
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
// io.run(); is required for all sketches.
|
|
// it should always be present at the top of your loop
|
|
// function. it keeps the client connected to
|
|
// io.adafruit.com, and processes any incoming data.
|
|
io.run();
|
|
|
|
/* Get a new accel. sensor event */
|
|
sensors_event_t event;
|
|
accel.getEvent(&event);
|
|
|
|
accelX = event.acceleration.x;
|
|
accelY = event.acceleration.y;
|
|
accelZ = event.acceleration.z;
|
|
|
|
/* Display the results (acceleration is measured in m/s^2) */
|
|
Serial.print("X: "); Serial.print(accelX); Serial.print(" ");
|
|
Serial.print("Y: "); Serial.print(accelY); Serial.print(" ");
|
|
Serial.print("Z: "); Serial.print(accelZ); Serial.print(" ");Serial.println("m/s^2 ");
|
|
|
|
// Read and print out the temperature
|
|
tempC = tempsensor.readTempC();
|
|
Serial.print("Temperature: "); Serial.print(tempC); Serial.println("C");
|
|
|
|
Serial.println("Sending to Adafruit IO...");
|
|
huzzah_temperature->save(tempC, 0, 0, 0, 2);
|
|
huzzah_accel_x->save(accelX);
|
|
huzzah_accel_y->save(accelY);
|
|
huzzah_accel_z->save(accelZ);
|
|
Serial.println("Data sent!");
|
|
|
|
Serial.print("Waiting ");Serial.print(IO_DELAY);Serial.println(" seconds...");
|
|
// wait IO_DELAY seconds between sends
|
|
for (int i = 0; i < IO_DELAY; i++)
|
|
{
|
|
delay(1000);
|
|
}
|
|
}
|