* fix(example): Add better WPS logging
Provides a better log of what went wrong when using WPS
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
* feat(eth): Allow setting the RX task stack size
Default stack size of 2K might not be enough in some cases. Increase the default to safer 4K and allow setting it to custom value.
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
* Fix timeout in WebServer::_uploadReadByte and set timeout handleClient()
Fixes: #9990
* Set HTTP_MAX_CLOSE_WAIT equal to other HTTP_xxx_WAIT values
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
If the interface is already connected, try to enable IPv6 immediately. Otherwise the interface would need to go through disconnect/connect cycle for IPv6 to be enabled.
* feat(OThread): Add Library
* fix(OpenThread): fixes file list in CMakeLists.txt
* fix(openthread): Fixes JSON CI Files
* fix(openthread): Fixes JSON CI Files
* fix(openthread): Include Openthread guarding
* fix(openthread): COAP parametrization
* fix(openthread): Include Openthread guarding
* fix(openthread): Improves commentaries and code
* fix(openthread): Improves code
* fix(openthread): Includes StreamString.h
* feat(openthread): New Scan Example
* feat(openthread): Improved Scan Example
* feat(openthread): README.md
Initial documentation for ESP3 Arduino OpenThread CLI API.
* feat(openthread): helper functions documentation
Create helper_functions.md for ESP32 Arduino OpenThread API
* fix(openthread): begin end
* feat(openthread): onReceice example
* fix(openthread): tx queue error
* fix(doc): fixing documentation apresentation
Fixes the documentation first paragraph in order to make it easier fore reading. It also displays in the very top which SoC are supported by the library.
* fix(doc): documentation format
* feat(openthread): commentary
* fix(openthread): Typo, start/stop console
* fix(openthread): library properties
* ci(pre-commit): Apply automatic fixes
* feat(openthread): formatting text
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: Lucas Saavedra Vaz <32426024+lucasssvaz@users.noreply.github.com>
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
* fix(ppp): Make modem reset delay configurable
The delay required to reset Simcom modem modules varies significantly across
different models, even where they have otherwise identical AT command
sets.
Simcom A7672 was failing to reset with the default 200ms delay. Make the reset
delay configurable to allow customising this for a specific modem.
Default delay, if not specified is kept at 200ms.
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
* feat(net): Deprecate old WiFi APIs
Deprecates WiFiClient, WiFiServer, WiFiUdp and WiFiClientSecure
* fix(net): add defines to WiFi.h
Defines are added to not cause deprecation warnings. Will be removed in the future
* fix(net): Use typedefs instead to help with forward declarations
Defines do not allow forward declarations
* HTTPClient lib - add HTTPCLIENT_NOSECURE build flag
`HTTPCLIENT_NOSECURE` build flag disables TLS support in HTTPClient library by
excluding `NetworkClientSecure.h` header.
This allows linker to strip down mbedTLS lind and certificates bundle,
which in turn reduces firmware image for about ~80kib.
* Update HTTPClient.cpp
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: Me No Dev <me-no-dev@users.noreply.github.com>
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
* fix(example): EXT0 and EXT1 wakeup
Fixes the Deep Sleep wakup example to run with IDF5.1. The API has changed and a adjustment was necessary.
* feat(wakeup): Use Macro for GPIO_NUM
Changed the example to use a #define for the RTC IO Pin (GPIO) used in the example.
* fix(typo): typo and commentaries
Fixes the commentary to the correct IDF terms.
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
Adds a class for 0x2901 - Characteristic User Descriptor.
This Descriptor is usual in BLE and describes with text what each characteristic is about.
Improve Notify.ino example by adding the 0x2901 descriptor
* fix(netbios): Return interface address for NetBIOS
When NetBIOS returns a match, it should return the IP address of the device.
Presently, however, it returns the address of multicast IP for the subnet
since the incoming NBNS packet's UDP target will be multicast
(i.e. 192.168.1.255).
Iterate over the active network interfaces and check netmasks to determine
where the packet came from, and return the appropriate IP interface address
instead.
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
* fix(wifi): Fix WiFi setTxPower and getTxPower
We need to wait for the interface to be started in order to be able to set/get TX Power. Code was returning too early, so calling the functions after `begin()` resulted in failure.
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
* feat: added support for filters in webserver
* feat: add setFilter function in StaticRequestHandler
* fix: ON_STA_FILTER & ON_AP_FILTER
* fix: make request handlers backward compatible
* fix: ON_STA_FILTER & ON_AP_FILTER
* fix: more filters to their own example
* chore: grammar
* fix: remove filters from header file
* fix: use same root route for both interfaces
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
* fix(ssl): Fix load stream memory leak
Loading Ca Cert/Certificate or Private Key from stream was leaking memory, due to buffers not being freed.
* fix(ssl): Cast the buffers to non-const
* fix(net): Don't unreg events if there are netifs
Unregister IP events only if all other netifs are stopped.
* fix(eth): Delete mac and phy on end
* fix(net): Update pin naming and log levels
* IDF release/v5.1 01b912a9e5
* Fix USB OTG Init on new IDF
* Delete libraries/TFLiteMicro/examples/micro_speech directory
Done in order to fix a CI problem created by an entire folder that was removed in original Library Repository.
* IDF release/v5.1 442a798083
* Update esp32-hal-tinyusb.c
---------
Co-authored-by: Rodrigo Garcia <rodrigo.garcia@espressif.com>
* (feat)usbmsc: Add is_writable function
Add is_writable function to the USBMSC class.
Allows USBMSC to be mounted in read-only mode.
* Update USBMSC.ino
Changes to USB Mass Storage (MSC) example code in Arduino USB library
* Added MSC.isWritable(true) line to set the disk as writable
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: Rodrigo Garcia <rodrigo.garcia@espressif.com>
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
* fix: NetworkClient - close the connection in stop() method
for all copies referring it
* ci(pre-commit): Apply automatic fixes
---------
Co-authored-by: Me No Dev <me-no-dev@users.noreply.github.com>
Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
