6fb55a7f68
* feat(board): Update 3rd party board Huidu HD-WF2/HD-WF4 Followup #10779 - fixed flash mode to 'dio' - removed psram flags - corrected gpio mapping defines * ci(pre-commit): Apply automatic fixes --------- Co-authored-by: pre-commit-ci-lite[bot] <117423508+pre-commit-ci-lite[bot]@users.noreply.github.com>
111 lines
2.9 KiB
C
111 lines
2.9 KiB
C
#ifndef Pins_Arduino_h
|
|
#define Pins_Arduino_h
|
|
|
|
#include <stdint.h>
|
|
|
|
// Huidu HD-WF4 - esp32-s3 HUB75 driver board
|
|
// https://www.hdwell.com/Product/index46.html
|
|
// https://github.com/mrcodetastic/ESP32-HUB75-MatrixPanel-DMA/discussions/667
|
|
|
|
#define USB_VID 0x303a
|
|
#define USB_PID 0x1001
|
|
|
|
#define WF4_A_PIN 39
|
|
#define WF4_B_PIN 38
|
|
#define WF4_C_PIN 37
|
|
#define WF4_D_PIN 36
|
|
#define WF4_E_PIN 21
|
|
#define WF4_OE_PIN 35
|
|
#define WF4_CLK_PIN 34
|
|
#define WF4_LAT_PIN 33
|
|
|
|
// X1 HUB75
|
|
#define WF4_X1_R1_PIN 2
|
|
#define WF4_X1_R2_PIN 3
|
|
#define WF4_X1_G1_PIN 6
|
|
#define WF4_X1_G2_PIN 7
|
|
#define WF4_X1_B1_PIN 10
|
|
#define WF4_X1_B2_PIN 11
|
|
#define WF4_X1_CS_PIN 45 // CS gpio must be set HIGH to enable X1 output
|
|
|
|
// X2 HUB75
|
|
#define WF4_X2_R1_PIN 4
|
|
#define WF4_X2_R2_PIN 5
|
|
#define WF4_X2_G1_PIN 8
|
|
#define WF4_X2_G2_PIN 9
|
|
#define WF4_X2_B1_PIN 12
|
|
#define WF4_X2_B2_PIN 13
|
|
#define WF4_X2_CS_PIN WF4_X1_CS_PIN // CS gpio must be set HIGH to enable X2 output
|
|
|
|
// X3 HUB75
|
|
#define WF4_X3_R1_PIN 2
|
|
#define WF4_X3_R2_PIN 3
|
|
#define WF4_X3_G1_PIN 6
|
|
#define WF4_X3_G2_PIN 7
|
|
#define WF4_X3_B1_PIN 10
|
|
#define WF4_X3_B2_PIN 11
|
|
#define WF4_X3_CS_PIN 14 // CS gpio must be set HIGH to enable X3 output
|
|
|
|
// X4 HUB75
|
|
#define WF4_X4_R1_PIN 4
|
|
#define WF4_X4_R2_PIN 5
|
|
#define WF4_X4_G1_PIN 8
|
|
#define WF4_X4_G2_PIN 9
|
|
#define WF4_X4_B1_PIN 12
|
|
#define WF4_X4_B2_PIN 13
|
|
#define WF4_X4_CS_PIN WF4_X3_CS_PIN // CS gpio must be set HIGH to enable X4 output
|
|
|
|
// P1 is a UART connector
|
|
#define WF4_P1_RX_PIN 44
|
|
#define WF4_P1_TX_PIN 43
|
|
|
|
// P2: PCB holes gpio/gnd
|
|
#define WF4_P2_DATA_PIN 0 // GPIO0 boot
|
|
|
|
// P5: temperature sensor connector
|
|
#define WF4_P5_DATA_PIN 16
|
|
|
|
// P7: VCC/GPIO holes on PCB
|
|
#define WF4_P7_DATA_PIN 1
|
|
|
|
// P11: IR connector
|
|
#define WF4_P11_DATA_PIN 15
|
|
|
|
// P12: two gpio's, Vcc, GND
|
|
#define WF4_P12_DATA1_PIN 47
|
|
#define WF4_P12_DATA2_PIN 18
|
|
|
|
// S1 Button
|
|
#define WF4_S1_DATA_PIN 17
|
|
|
|
// S2-S3 PCB holes
|
|
#define WF4_S2_DATA_PIN 48
|
|
#define WF4_S3_DATA_PIN 26
|
|
#define WF4_S4_DATA_PIN 46
|
|
|
|
#define WF4_BUTTON_TEST WF4_S1_PIN // Test key button on PCB, 1=normal, 0=pressed
|
|
#define WF4_LED_RUN_PIN 40 // Status LED on PCB
|
|
#define WF4_BM8563_I2C_SDA 41 // RTC BM8563 I2C port
|
|
#define WF4_BM8563_I2C_SCL 42
|
|
#define WF4_USB_DN_PIN 19 // USB-A D-
|
|
#define WF4_USB_DP_PIN 20 // USB-A D+
|
|
|
|
#define LED_BUILTIN WF4_LED_RUN_PIN
|
|
#define BUILTIN_LED LED_BUILTIN // backward compatibility
|
|
|
|
static const uint8_t TX = WF4_P1_TX_PIN;
|
|
static const uint8_t RX = WF4_P1_RX_PIN;
|
|
|
|
static const uint8_t SDA = WF4_BM8563_I2C_SDA;
|
|
static const uint8_t SCL = WF4_BM8563_I2C_SCL;
|
|
|
|
// there is no dedicated SPI connector on board, but SPI could be accessed via PCB holes
|
|
static const uint8_t SS = WF4_S2_DATA_PIN;
|
|
static const uint8_t MOSI = WF4_S3_DATA_PIN;
|
|
static const uint8_t MISO = WF4_S4_DATA_PIN;
|
|
static const uint8_t SCK = WF4_P7_DATA_PIN;
|
|
|
|
// touch pins are mostly busy with HUB75 ports
|
|
static const uint8_t T1 = WF4_P7_DATA_PIN;
|
|
|
|
#endif /* Pins_Arduino_h */
|