arduino-esp32/cores/esp32/esp32-hal-rmt.h

// Copyright 2023 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at

//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

#ifndef MAIN_ESP32_HAL_RMT_H_
#define MAIN_ESP32_HAL_RMT_H_

#include "soc/soc_caps.h"
#if SOC_RMT_SUPPORTED

#ifdef __cplusplus
extern "C" {
#endif

typedef enum {
  RMT_RX_MODE = 0,  // false
  RMT_TX_MODE = 1,  // true
} rmt_ch_dir_t;

typedef enum {
  RMT_MEM_NUM_BLOCKS_1 = 1,
  RMT_MEM_NUM_BLOCKS_2 = 2,
#if SOC_RMT_TX_CANDIDATES_PER_GROUP > 2
  RMT_MEM_NUM_BLOCKS_3 = 3,
  RMT_MEM_NUM_BLOCKS_4 = 4,
#if SOC_RMT_TX_CANDIDATES_PER_GROUP > 4
  RMT_MEM_NUM_BLOCKS_5 = 5,
  RMT_MEM_NUM_BLOCKS_6 = 6,
  RMT_MEM_NUM_BLOCKS_7 = 7,
  RMT_MEM_NUM_BLOCKS_8 = 8,
#endif
#endif
} rmt_reserve_memsize_t;

// Each RMT Symbols has 4 bytes
// Total number of bytes per RMT_MEM_BLOCK is RMT_SYMBOLS_PER_CHANNEL_BLOCK * 4 bytes
typedef union {
  struct {
    uint32_t duration0 : 15;
    uint32_t level0 : 1;
    uint32_t duration1 : 15;
    uint32_t level1 : 1;
  };
  uint32_t val;
} rmt_data_t;

// Reading and Writing shall use as rmt_symbols_size this unit
// ESP32 has 8 MEM BLOCKS in total shared with Reading and/or Writing
// ESP32-S2 has 4 MEM BLOCKS in total shared with Reading and/or Writing
// ESP32-S3 has 4 MEM BLOCKS for Reading and another 4 MEM BLOCKS for Writing
// ESP32-C3 has 2 MEM BLOCKS for Reading and another 2 MEM BLOCKS for Writing
#define RMT_SYMBOLS_PER_CHANNEL_BLOCK SOC_RMT_MEM_WORDS_PER_CHANNEL

// Used to tell rmtRead() to wait for ever until reading data from the RMT channel
#define RMT_WAIT_FOR_EVER ((uint32_t)portMAX_DELAY)

// Helper macro to calculate the number of RTM symbols in a array or type
#define RMT_SYMBOLS_OF(x) (sizeof(x) / sizeof(rmt_data_t))

/**
    Initialize the object
    
    New Parameters in Arduino Core 3: RMT tick is set in the rmtInit() function by the 
    frequency of the RMT channel. Example: 100ns tick => 10MHz, thus frequency will be 10,000,000 Hz
    Returns <true> on execution success, <false> otherwise
*/
bool rmtInit(int pin, rmt_ch_dir_t channel_direction, rmt_reserve_memsize_t memsize, uint32_t frequency_Hz);

/**
     Sending data in Blocking Mode. 
     <rmt_symbol> is a 32 bits structure as defined by rmt_data_t type.
     It is possible to use the macro RMT_SYMBOLS_OF(data), if data is an array of <rmt_data_t>.
     
     Blocking mode - only returns after sending all data or by timeout. 
     If the writing operation takes longer than <timeout_ms> in milliseconds, it will end its
     execution returning <false>.
     Timeout can be set as undefined time by passing <RMT_WAIT_FOR_EVER> as <timeout_ms> parameter.
     When the operation is timed out, rmtTransmitCompleted() will return <false> until the transmission
     is finished, when rmtTransmitCompleted() will return <true>.

     Returns <true> when there is no error in the write operation, <false> otherwise, including when it
     exits by timeout.
*/
bool rmtWrite(int pin, rmt_data_t *data, size_t num_rmt_symbols, uint32_t timeout_ms);

/**
     Sending data in Async Mode.
     <rmt_symbol> is a 32 bits structure as defined by rmt_data_t type.
     It is possible to use the macro RMT_SYMBOLS_OF(data), if <data> is an array of <rmt_data_t>

     If more than one rmtWriteAsync() is executed in sequence, it will wait for the first transmission 
     to finish, resulting in a return <false> that indicates that the rmtWriteAsync() call has failed. 
     In such case, this channel will have to finish the previous transmission before starting a new one.
     
     Non-Blocking mode - returns right after execution.
     Returns <true> on execution success, <false> otherwise.

     <bool rmtTransmitCompleted(int pin)> will return <true> when all data is sent.
*/
bool rmtWriteAsync(int pin, rmt_data_t *data, size_t num_rmt_symbols);

/**
     Writing data up to the reserved memsize, looping continuously
     <rmt_symbol> is a 32 bits structure as defined by rmt_data_t type.
     It is possible to use the macro RMT_SYMBOLS_OF(data), if data is an array of rmt_data_t

     If *data or size_byte are NULL | Zero, it will disable the writing loop and stop transmission  

     Non-Blocking mode - returns right after execution
     Returns <true> on execution success, <false> otherwise

     <bool rmtTransmitCompleted(int pin)> will return always <true> while it is looping.
*/          
bool rmtWriteLooping(int pin, rmt_data_t* data, size_t num_rmt_symbols);

/**
     Checks if transmission is completed and the rmtChannel ready for transmiting new data.
     To be ready for a new transmission, means that the previous transmission is completed.
     Returns <true> when all data has been sent, <false> otherwise.
     The data transmition information is reset when a new rmtWrite/Async function is called.
     If rmtWrite() times out or rmtWriteAsync() is called, this function will return <false> until 
     all data is sent out. 
     rmtTranmitCompleted() will always return <true> when rmtWriteLooping() is called, 
     beacuse it has no effect in such case.
*/
bool rmtTransmitCompleted(int pin);

/**
     Initiates blocking receive. Read data will be stored in a user provided buffer <*data>
     It will read up to <num_rmt_symbols> RMT Symbols and the value of this variable will 
     change to the effective number of symbols read.
     <rmt_symbol> is a 32 bits structure as defined by rmt_data_t type.

     If the reading operation takes longer than <timeout_ms> in milliseconds, it will end its
     execution and the function will return <false>. In a time out scenario, <num_rmt_symbols> won't 
     change and rmtReceiveCompleted() can be used latter to check if there is data available.
     Timeout can be set as undefined time by passing RMT_WAIT_FOR_EVER as <timeout_ms> parameter

     Returns <true> when there is no error in the read operation, <false> otherwise, including when it
     exits by timeout.
     Returns, by value, the number of RMT Symbols read in <num_rmt_symbols> and the user buffer <data> 
     when the read operation has success within the defined <timeout_ms>. If the function times out, it
     will read RMT data latter asynchronously, affecting <*data> and <*num_rmt_symbols>. After timeout,
     the application can check if data is already available using <rmtReceiveCompleted(int pin)>
*/
bool rmtRead(int pin, rmt_data_t* data, size_t *num_rmt_symbols, uint32_t timeout_ms);

/**
     Initiates async (non-blocking) receive. It will return immediately after execution.
     Read data will be stored in a user provided buffer <*data>.
     It will read up to <num_rmt_symbols> RMT Symbols and the value of this variable will 
     change to the effective number of symbols read, whenever the read is completed.
     <rmt_symbol> is a 32 bits structure as defined by <rmt_data_t> type.

     Returns <true> when there is no error in the read operation, <false> otherwise. 
     Returns asynchronously, by value, the number of RMT Symbols read, and also, it will copy 
     the RMT received data to the user buffer <data> when the read operation happens.
     The application can check if data is already available using <rmtReceiveCompleted(int pin)>
*/
bool rmtReadAsync(int pin, rmt_data_t* data, size_t *num_rmt_symbols);

/**
     Checks if a data reception is completed and the rmtChannel has new data for processing.
     Returns <true> when data has been received, <false> otherwise.
     The data reception information is reset when a new rmtRead/Async function is called.
*/
bool rmtReceiveCompleted(int pin);

/**
   Function used to set a threshold (in ticks) used to consider that a data reception has ended.
   In receive mode, when no edge is detected on the input signal for longer than idle_thres_ticks 
   time, the receiving process is finished and the Data is made available by 
   the rmtRead/Async functions. Note that this time (in RMT channel frequency cycles) will also
   define how many low/high bits are read at the end of the received data.
   The function returns <true> if it is correctly executed, <false> otherwise.
*/
bool rmtSetRxMaxThreshold(int pin, uint16_t idle_thres_ticks);

/**
   Parameters changed in Arduino Core 3: low and high (ticks) are now expressed in Carrier Freq in Hz and
   duty cycle in percentage float 0.0 to 1.0 - example: 38.5KHz 33% High => 38500, 0.33
   
   Function to set a RX demodulation carrier or TX modulation carrier 
    <carrier_en> is used to enable/disable the use of demodulation/modulation for RX/TX
    <carrier_level> true means that the polarity level for the (de)modulation is positive
    <frequency_Hz> is the carrier frequency used
    <duty_percent> is a float deom 0 to 1 (0.5 means a square wave) of the carrier frequency 
   The function returns <true> if it is correctly executed, <false> otherwise.
*/
bool rmtSetCarrier(int pin, bool carrier_en, bool carrier_level, uint32_t frequency_Hz, float duty_percent);

/**
   Function used to filter input noise in the RX channel.
   In receiving mode, channel will ignore any input pulse which width (high or low) 
   is smaller than <filter_pulse_ticks>
   If <filter_pulse_ns> is Zero, it will to disable the filter.
   The function returns <true> if it is correctly executed, <false> otherwise.
*/
bool rmtSetRxMinThreshold(int pin, uint8_t filter_pulse_ticks);

/**
   Deinitializes the driver and releases all allocated memory
   It also disables RMT for this gpio
*/
bool rmtDeinit(int pin);

#ifdef __cplusplus
}
#endif

#endif /* SOC_RMT_SUPPORTED */
#endif /* MAIN_ESP32_HAL_RMT_H_ */