* Add PIO-based SoftwareSPI enabling SPI on any pins
The Raspberry Pi team has a working PIO-based SPI interface. Wrap it
to work like a hardware SPI interface, allowing SPI on any pin
combination.
Tested reading and writing an SD card using unmodified SD library.
* Add W5500 example
Good for testing, shows non-contiguous pin outs.
* Added buffer read to `AudioBufferManager` and `I2S`. Example and documentation included.
* Update type of words to unsigned in example.
* Improve buffered loopback example.
* Remove const from read buffer.
* Replace ESP8266SdFat w/SdFat 2.3.0, add SDIO and ExFAT support
Remove ESP8266SdFat fork and replaces with upstream SdFat to simplify
maintenance.
This 2.3.0 version adds SDIO support and enables exFAT support.
Also upgraded FAT filename support to 256 chars, identical to LittleFS.
* Add SDIO support to SD and SDFS, documentation, and examples
* Update SD examples to all support SPI0, SPI1, or SDIO
Semihosting is handy for debugging, so allow the core to use `SerialSemi` as the
::printf port. Add menu item to the IDE to allow selection.
Add RISC-V implementation of semihost call
Adds a menu item to enable onboard profiling. This requires significant
RAM and really only makes sense on devices with PSRAM to store the state.
When the menu item is selected, allocates RAM and tracks function calls and
periodically samples the PC to generate a histogram of application usage.
The onboard gmon.out file can be written over Semihosting or
some other way to transfer to a PC for analysis.
Adds a profiling example with command lines.
Enable ARM-only semihosting mode. This mode allows applications on the
Pico to write to the OpenOCD console and read and write files on the
host system (i.e. debugging dump information, etc.)
It is not very fast because of the way it uses breakpoints on the Pico
to communicate, but it is useful in cases when you want to get a single
file off of the Pico while debugging.
Note that this **requires** a connected OpenOCD and GDB or else the
semihosting will cause a system panic.
The RP2350 boot ROM seems to randomize memory on a HW reset, including
both CPU stacks where we normally stuff the "reset to bootloader" flag.
Update the docs and source to remove rp2040.enableDoubleResetBootloader()
on RP2350-based boards.
Fixes#2606
* Enable LWIP IGMP, MDNS internal server
* Enable MDNS lookup from LWIP DNS
* Add SimpleMDNS responder, small code and no malloc
* Ensure we copy out lwipopts in make-libpico
Adds a small wrapper around the LWIP-provided MDNS responder application.
Drop-in replacement in many basic cases for LEAmDNS.
For FreeRTOS it is important to not allocate memory on an LWIP callback.
LEAmDNS needs to do this to create response objects, leading to crashes.
Increase LWIP timers by bumping the LWIP_ARP number (as done before).
Replace ArduinoOTA LEAmDNS with SimpleMDNS and update a
HTTPUpdateServer example.
* Adds RISC-V compilation option to the IDE and Platform.IO.
* Build RP2350-RISCV libpico, libbearssl
* Fix RP2350 BearSSL library (was copied from RP2040, now built for M33)
* New GCC 14.2 toolchain is required (12.4 RISC-V support is borked)
* Newlib locking fixed prototypes
* Manually force all runtime init code into RP2350 binaries
* Add RISC-V to CI
* Remove RP2350 BOOT2.S files, binaries (not used)
* Clean up minor GCC 14.x warnings
* Add RP2350-RISCV OTA build, link
* Add RISC-V FreeRTOS files (configuration still not running, but builds)
* Add basic documentation
The RP2350 has a different blob header requirement to identify a working
image. Ensure that header is present in the OTA loader.
Update the PicoOTA examples for the 2350
* Add support for the extra 16 GPIO pins in the menus and core.
* Clean up Generic RP2350 PSRAM ("none" is valid) and flash (other than 16MB) options.
* Add extra GPIO<->peripheral connections
* Add Pimoroni PGA2350 RP2350B-based board
* Pins 32-47 can be used for PIOPrograms
* Avoid hang when PSRAM fails to initialize
* Move libpico to an RP2350B board for SDK (otherwise the SDK drops all GPIOHI support)
Use real GPIO pad inversion to allow inverted RX, TX, and controls for
the hardware UART and software PIO-emulated serial ports.
Adds ``setInvertTX(bool)`` and ``setInvertRX(bool)`` calls to both ports,
with ``setInvertControl(bool)`` for the HW UARTS.
* Migrate RP2040-specific bits to separate dirs
* Add chip to boards.txt, isolate RP2040-specifics
* Add RP2350 boot2, bearssl, and libraries
* Platform.IO adjust to new paths
* Add RPIPICO2 JSON for P.IO
* Add RP2350 to Platform.io
* Update Picotool and OpenOCD for all hosts
* Use picotool to generate UF2s
* Build separate libpico blobs serially
Thanks for the review, @aarturo182 !
* Add RP2350 to CI
* Allow Ethernet/WiFi building for RP2350
* Update Adafruit TinyUSB to latest
* Test skip fix
* Make RP2350 Picotool work. update USB ID
* Fix EEPROM/FS flash locations
RP2350 adds a 4K header sector to the UF2, meaning we have 4K less total
flash to work with. Adjust all constants appropriately on the RP2350.
* Adds ilabs board and PSRAM support. (#2342)
* Adds iLabs boards and basic PSRAM support.
* Make PSRAM come up as part of chip init
Uses SparkFun psram.cpp to set timings on clocks which are defined in the
variant file. Prefix things with RP2350_PSRAM_xxx for sanity.
Users don't need to call anything, PSRAM "just appears". Still need to
add in malloc-type allocation.
* Add board SparkFun ProMicro RP2350
Same pinout as the SparkFun ProMicro RP2040 with 8MB PSRAM and RP2350
* Add TLSF library for use w/PSRAM
Fork of upstream to include add'l C++ warning fixes.
* Add pmalloc/pcalloc to use PSRAM memory
free() and realloc() all look at the pointer passed in and jump to the
appropriate handler. Also takes care of stopping IRQs and taking the
malloc mutex to support multicore and FreeRTOS (when that workd)
* Fix BOOTSEL for RP2350
* Add simple rp2040.idleOtherCore test
* Add Generic RP2350 and clean up PSRAM menus
Commercial boards now only have 1 size PSRAM, no need to have menu for them.
* Add Solder Party RP2350 Stamp boards (#2352)
* Add PSRAM heap info helpers, mutex lock mallinfo
* Add RP2350 docs
* FreeRTOS and OTA unsupported warnings for RP2350
* Add VFS to enable POSIX file I/O operations
Enables use of FILE * operations on internal and external storage. fopen,
fclose, fseek, fprintf, fscanf, etc. supported.
* Add FS/File::stat and support POSIX stat/fstat
RP2040::memcpyDMA implements a DMA-controlled memory copy call identical in
function to standard memcpy, but using an onboard DMA engine. For large
memory transfers this can be significantly faster than using the CPU-based
memcpy. Only 4-byte aligned source, destination, and counts are allowed.
If any inputs are not 4-byte aligned, then standard memcpy will occur so
it will behave correctly for any inputs.
