diff --git a/samples/drivers/led_xec/README.rst b/samples/drivers/led_xec/README.rst
index 883126640d3..072ef1abb80 100644
--- a/samples/drivers/led_xec/README.rst
+++ b/samples/drivers/led_xec/README.rst
@@ -9,12 +9,16 @@ Overview
 This sample allows to test the Microchip led-xec driver which uses the
 breathing-blinking LED (BBLED) controllers. The SoC design is fixed
 allowing each BBLED control over one specific GPIO.
+
 MEC15xx and MEC172x:
-BBLED controller 0 uses GPIO 0156.
-BBLED controller 1 uses GPIO 0157.
-BBLED controller 2 uses GPIO 0153.
-MEC172x has a fourth instance of BBLED.
-BBLED controller 3 uses GPIO 0035
+
+- BBLED controller 0 uses GPIO 0156.
+- BBLED controller 1 uses GPIO 0157.
+- BBLED controller 2 uses GPIO 0153.
+
+MEC172x has a fourth instance of BBLED:
+
+- BBLED controller 3 uses GPIO 0035
 
 Test pattern
 ============
@@ -27,44 +31,50 @@ For each LEDs (one after the other):
 - Blinking on: 1 sec, off: 1 sec
 
 Board Jumpers
-********************
+*************
 
-EVB: mec172xevb_assy6906
-BBLED0 GPIO 0156.
-Connect GPIO 0156 to board LED4 by placing a wire from JP71-11 to J47-3.
-Make sure there are no jumpers on JP54 1-2 and JP21 4-5
+mec172xevb_assy6906 evaluation board
+====================================
 
-BBLED1 GPIO 0157.
-Connect GPIO 0156 to board LED5 by placing a wire from JP71-12 to J48-3.
-Make sure there are no jumpers on JP54 3-4 and JP21 16-17
+- BBLED0: GPIO 0156.
+       - Connect GPIO 0156 to board LED4 by placing a wire from JP71-11 to J47-3.
+       - Make sure there are no jumpers on JP54 1-2 and JP21 4-5
 
-BBLED2 GPIO 0153.
-Connect GPIO 0153 to board LED7 by placing a wire from JP71-5 to JP146-5.
-JP146-5 is connected to MEC172x VCI_OUT1 without a jumper. Force VCI_OUT1
-high by forcing VCI_IN1 high: install jumper on J55 3-4 which pulls VCI_IN1
-to the VBAT rail via a 100K pull-up. Requires VBAT power rail is connected
-to VTR or some other power source.
+- BBLED1: GPIO 0157.
+       - Connect GPIO 0156 to board LED5 by placing a wire from JP71-12 to J48-3.
+       - Make sure there are no jumpers on JP54 3-4 and JP21 16-17
 
-BBLED3 GPIO 0035.
-Connect GPIO 0035 to board LED7 by placing a wire from JP67-19 to JP146-1.
-Make sure there is no jumper on JP79 17-18.
-JP146-1 is connected to MEC172x VCI_OUT2 without a jumper. Force VCI_OUT2
-high by forcing VCI_IN2 high: install a jumper on J55 5-6 which pulls VCI_IN2
-to the VBAT rail via a 100K pull-up. Requires VBAT power rail is connected
-to VTR or some other power source.
+- BBLED2: GPIO 0153.
+       - Connect GPIO 0153 to board LED7 by placing a wire from JP71-5 to JP146-5.
 
-EVB: mec15xxevb_assy6853
-BBLED0 GPIO 0156.
-Add jumper on JP41 1-2 to connect GPIO 0156 to board LED2
-Remove jumper on JP31 13-14
+         JP146-5 is connected to MEC172x VCI_OUT1 without a jumper. Force VCI_OUT1
+         high by forcing VCI_IN1 high: install jumper on J55 3-4 which pulls VCI_IN1
+         to the VBAT rail via a 100K pull-up. Requires VBAT power rail is connected
+         to VTR or some other power source.
 
-BBLED1 GPIO 0157.
-Add jumper on JP41 3-4 to connect GPIO 0157 to board LED3
-Remove jumper on JP31 15-16
+- BBLED3: GPIO 0035.
+       - Connect GPIO 0035 to board LED7 by placing a wire from JP67-19 to JP146-1.
+       - Make sure there is no jumper on JP79 17-18.
 
-BBLED2 GPIO 0153.
-Add jumper on JP41 3-4 to connect GPIO 0153 to board LED4
-Remove jumper on JP31 17-18
+         JP146-1 is connected to MEC172x VCI_OUT2 without a jumper. Force VCI_OUT2
+         high by forcing VCI_IN2 high: install a jumper on J55 5-6 which pulls VCI_IN2
+         to the VBAT rail via a 100K pull-up. Requires VBAT power rail is connected
+         to VTR or some other power source.
+
+mec15xxevb_assy6853 evaluation board
+====================================
+
+- BBLED0: GPIO 0156.
+       - Add jumper on JP41 1-2 to connect GPIO 0156 to board LED2
+       - Remove jumper on JP31 13-14
+
+- BBLED1: GPIO 0157.
+       - Add jumper on JP41 3-4 to connect GPIO 0157 to board LED3
+       - Remove jumper on JP31 15-16
+
+- BBLED2: GPIO 0153.
+       - Add jumper on JP41 3-4 to connect GPIO 0153 to board LED4
+       - Remove jumper on JP31 17-18
 
 Building and Running
 ********************