Add devicetree node for code RAM, code RAM can be accessed
over AIXM bus or AXIF bus. Code access via AXIF interface
provides the best optimal performance
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
This commit adds a runner wrapper for the 'minichlink' program which
offers a free, open mechanism to use the CH-LinkE programming dongle for
the CH32V003.
https://github.com/cnlohr/ch32v003fun/tree/master/minichlink
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds support for the CH32V003EVT board which features a
32-bit general-purpose RISC-V MCU.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
The ram0x partitions seem to be not compliant with nRF54H20
architecture and it causes that in the application dts overlay file
it is difficult to extend cpuapp_ram0x_region without modifying
whole layout.
It is better to place cpurad_ram0x_region at the beginning at
2f010000 address and then cpuapp_ram0x_region right after that.
Thanks to that, if the application needs to have more than 256 kB
of RAM, in the application dts overlay file, a user can increase
cpuapp_ram0x_region size up to 2f0be000.
Signed-off-by: Arkadiusz Balys <arkadiusz.balys@nordicsemi.no>
Add missing "pinctrl-names" and "status" properties for
the spi1 node in ek_ra8m1.dts to able to test spi_loopback
on ek_ra8m1
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
The B_L4S5I_IOT01A Discovery kit does not boot up when using --sysbuild.
The error is caused by slot0_partition which is assigned an address of
0x1000 which overlaps with the boot_partition. Setting the address to
0x10000 fixed it.
Signed-off-by: Winston Arrocena <we.arrocena@gmail.com>
Added mikrobus_header, mikrobus_i2c, mikrobus_spi and mikrobus_serial
node labels to da14695_dk_usb device tree board definition, allowing
compatible shield boards to be used. Also fixed minor issues with
pin assignment and header labelling.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Enable BLE feature for Nucleo-WB09KE and Nucleo-WB05KZ.
Dedicate 32KB and 8KB at the end of flash memory to storage partition on
Nucleo-WB09KE and Nucleo-WB05KZ respectively.
Add ble tag to the both devices yaml file.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
`_current` is now functionally equals to `arch_curr_thread()`, remove
its usage in-tree and deprecate it instead of removing it outright,
as it has been with us since forever.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Use a string for the mipi-mode property over an integer value, as this
significantly improves the readability of the MIPI DBI device binding.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The NXP LCDIC peripheral contains two internal timers, with configurable
periods. These times are used to determine delays within the peripheral,
such as the reset and tearing enable signal delays. Allow these periods
to be set within the devicetree for the peripheral.
Raise the period where required for display drivers that need a value
other than the reset setting
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add note about compatible change for NXP PORT IP. Also, update
references to the DT compatible within board docs.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
* Replace copies of fixed-partitions nodes in related boards by
referencing the apropriate partition table from the available list.
* For better reference the `partitions_*.dtsi` file has boot offset,
purpose and the flash size encoded in the file name. Default flash size
is considered to be 4MB.
* Added the flash size node for the boards which are not based on the
module.
* Removed flash size registry from the esp32.*common.dtsi
Signed-off-by: Marek Matej <marek.matej@espressif.com>
STM32F4 series flash layout is as follows:
{.pages_count = 4, .pages_size = KB(16)},
{.pages_count = 1, .pages_size = KB(64)},
{.pages_count = 7, .pages_size = KB(128)}
Since NVS subsys requires 2 sectors of max 32K in total, provide a
flash partition which respects this constraint using 2 of the 16K sectors
in the beginning of the layout.
Provide a compatible flash partition usable with mcuboot, but keep the
storage partition commented as its usage is not compatible with use w/o
mcuboot enabled (in this case main image starts as offset 0 which conflicts
with storage partition).
Note that it isn't possible either to get main image starting directly
in the 128K sectors w/o bootloader as boot flash address can't be
configured.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
NVS susbsystem requires a slot covering 2 sectors of flash, which
should be at minimum 8K on L1 series which provides 4K sectors.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
NVS susbsystem requires a slot covering 2 sectors of flash, which
should be at minimum 4K on G0 series which provised 2K sectors.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
STM32F2 series flash layout is as follows:
{.pages_count = 4, .pages_size = KB(16)},
{.pages_count = 1, .pages_size = KB(64)},
{.pages_count = 7, .pages_size = KB(128)}
Since NVS subsys requires 2 sectors of max 32K in total, provide a
flash partition which respects this constraint using 2 of the 16K sectors
in the beginning of the layout.
Provide a compatible flash partition usable with mcuboot, but keep the
storage partition commented as its usage is not compatible with use w/o
mcuboot enabled (in this case main image starts as offset 0 which conflicts
with storage partition).
Note that it isn't possible either to get main image starting directly
in the 128K sectors w/o bootloader as boot flash address can't be
configured.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Align the total SRAM size for STM32L47x/L48x/L49x/L4Ax
boards. Those MCUs with up to 320 Kbytes SRAM:
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Align the total SRAM size for STM32L47x/L48x/L49x/L4Ax
boards. Those MCUs with up to 320 Kbytes SRAM:
• 96 Kbytes SRAM1 and 32 Kbyte SRAM2 on STM32L47x/L48x.
• 256 Kbyte SRAM1 and 64 Kbyte SRAM2 on STM32L49x/L4Ax
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The board shares many features with other Arduinos based on STM32H747
(like the HSE in bypass mode).
Once https://github.com/zephyrproject-rtos/zephyr/pull/76542 is merged,
PF1550 support should be added too to allow switching IO voltage
from 3v3 to 1v8
Signed-off-by: Martino Facchin <m.facchin@arduino.cc>
Right now, USART1 is enabled on the M7 target variant by default, leaving
M4 without a UART to use; this is the way this port was originally
contributed.
Since then, USB was enabled on M7, changing the console backend from USART1
to USB CDC ACM; the M4 target was left unchanged.
This commit enabled USART1 on the M4 variant and disabled it on the M7
variant, so that the M4 variant can use it as its console backend.
Note that, for the M4 variant, USART1 has been assigned to `zephyr,console`
and `zephyr,shell-uart` since this port was contributed, even though USART1
was always disabled on M4.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Include in the list of supported peripherals the UARTE for the
simulated nrf54l15
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The HW models now support this peripheral for this target.
Let's enable it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The nRF54L05 and nRF54L10 are identical to the nRF54L15 except for their
memory sizes. Add support for emulating those ICs on the nRF54L15DK.
This commit only adds support for the main application core. Support for
the FLPR core may be added later.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the rather logical convention for the name that is applied to other
Nordic boards: <board>_common.dtsi for definitions that are common to
the board itself (LEDs, buttons, etc).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
device tree:
enable support for the SDHC controller to use the micro SD card slot
documentation:
- added instructions for SD card and OLED samples
- added links to code samples
defconfig:
added CONFIG_ESP32_USE_UNSUPPORTED_REVISION=y to
ttgo_lora32_esp32_procpu_defconfig
The chip on the board is a ESP32 chip revision 1.
The board will not boot, it displays the following warning at boot:
I (35) boot: chip revision: v1.0
E (38) boot: You are using ESP32 chip revision (1) that is unsupported.
While it may work, it could cause unexpected behavior or issues.
E (50) boot: Proceeding with this ESP32 chip revision is not recommended
unless you fully understand the potential risk and limitations.
E (62) boot: If you choose to continue, please enable the
'CONFIG_ESP32_USE_UNSUPPORTED_REVISION' in your project configuration.
E (73) boot: HW init failed, aborting
In order to prevent a boot loop, CONFIG_ESP32_USE_UNSUPPORTED_REVISION=y
was added to the defconfig.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Use configdefault when enabling LV_COLOR_SWAP_16 within boards and
shield definitions, to avoid OR'ing the dependencies for the Kconfig
symbol. Otherwise, a user manually selecting LV_COLOR_DEPTH will
encounter build errors as LV_COLOR_SWAP_16 may be enabled when
LV_COLOR_DEPTH_16 is not selected
Fixes#81546
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
USE_HYPERRAM macro defined shouldn't be placed under
CONFIG_BOOT_FLEXSPI_NOR.
Add flexspi1 pinmux pinctrl and flash partitions
Add flash partitions and correct flash parameter.
This commit was tested with samples: flash_shell on cm33/cm7 cores
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
A valid device tree configuration is provided for the ADCs of the 8 input
channels and the sample adc_dt works out of the box. Obviously this is
not the only possible configuration but it provides a good template for
further customization without the need to lookup the ADC GPIOs and
connections in the schematics.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
This set of changes enables the RS485 hardware connected to usart3 and
provides some overlays that allow for easily running the modbus
rtu_client and rtu_server samples on Opta.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
Some changes to cleanup and clarify some device tree nodes:
* removed wrong sdram2 definition
* added all internal flash slots accessible from M4
* added all internal flash slots accessible from M7
* removed CONFIG_UART_LINE_CTRL because not needed by USB CDC ACM
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
This set of changes reorganize the ethernet configuration by removing the
use a regulator to enable the PHY: the correct GPIO pin is set in code
only if the network has been configured via CONFIG_NET_L2_ETHERNET.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
The prior image was of poor quality, making it difficult to interpret.
Updated the image with a higher-quality version.
Signed-off-by: Dhruv Menon <dhruvmenon1104@gmail.com>
To remove CONFIG_PINCTRL from board side for numaker boards.
The Drivers using Pinctrl should be turning Pinctrl on
instead of the responsibility of the board.
Fixes#78619
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add `hifive_unmatched//s7` (earlier selected by default, using
`hifive_unmatched`) and `hifive_unmatched//u74` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Add `hifive_unleashed//e51` (earlier selected by default, using
`hifive_unleashed`) and `hifive_unleashed//u54` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Switch from `ram0` to `l2lim` in `zephyr, sram` in board DTS
Add `l2lim` in `support/hifive_unleashed.resc` and targets l2lim
as a work-area in `openocd_hifive_unleashed.cfg`
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This option existed only to make the transition from native_posix to
native_sim easier. As native_posix is going to be removed in v4.2
we deprecate this option now, so it will also be removed.
We also switch this option to default to false already now.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This board has a few issues handled by this PR:
- Fix DTS entries to meet necessary flash partitions
- Fix wrong kconfig entries realted to SoC model
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Add UART configuration and pin control. Set state to disabled,
as it serves as alternative to default LPUART0 or as second
uart only.
Signed-off-by: Neil Chen <cheng.chen_1@nxp.com>
Add CONFIG_GPIO from defconfigs for Infineon boards.
Revert pull/81377, which affect some ble samples which
used GPIO.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
This commit changes the way some x86 devicetree set the unit-address values
of memory nodes. Before the change, they were always set to `0`. After the
change, they are derived from the `DT_DRAM_BASE` macro to match the first
address specified by the reg property.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Zephyr SDK 0.17.0 adds the toolchain for the Intel Audio DSP
ACE 3.0 platforms. We can now add the bits to enable building
the boards with SDK 0.17.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The patch modifies the "Programming and Debugging" and "Flashing" sections
to make the documentation clearer and consistent with what is reported for
other ST boards.
Suggested-by: Abderrahmane Jarmouni <git@jarmouni.me>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The building and flashing of the drivers/display and subsys/display/lvgl
examples confirmed that the LTDC peripheral is supported.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The commit e17e54c48f ("boards: stm32: add flashing with stm32cubeprog
for all") did not update the documentation regarding the flashing
section, which no longer uses the OpenOCD runner by default.
Fixes: e17e54c48f
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This commit defines the default pinctrl of ITM for Apollo3 and
Apollo4 EVB. Also configures the default SWO frequency.
Signed-off-by: Aaron Ye <aye@ambiq.com>
- Refactoring of the cmake code so LinkServer can be invoked with the
correct switches.
- Documentation update
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Openocd target cyw20829 does not define _TARGETNAME which is used by
default by the openocd west runner when using CONFIG_DEBUG_THREAD_INFO.
This is similar to the issue previously addressed for STM32H7:
Link: https://github.com/zephyrproject-rtos/zephyr/issues/45778
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Add MAX78002EVKIT board.
For more information about this board please check
https://www.analog.com/
Signed-off-by: Furkan Akkiz <hasanfurkan.akkiz@analog.com>
The nRF54H20 Development Kit version 0.8.0 is no longer supported, given
that they should have all been replaced by 0.9.x.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added pmod_serial and pmod_header node labels to EK-RA8M1 device
tree board definition, allowing compatible shield boards to be used.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Add USB node to apollo4p and apollo4p_blue qualifier, and apollo4p_evb
and apollo4p_blue_kxr_evb board to enableUSB support on the MCU and
its EVB.
Signed-off-by: Chew Zeh Yang <zeon.chew@ambiq.com>
Include in the list of supported peripherals the UARTE for the
simulated nrf5340
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The HW models now support this peripheral for these targets.
Let's enable them.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Include in the list of supported peripherals the GPIO
and GPIOT for both the nrf5340 and nrf54l15
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This will help distinguish 64 and 32-bit platforms by tooling, following
the pattern visible in e.g. RISC-V.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
atom.dtsi enforces "intel,x86", but it doesn't help us discern if the
platform is 32 or 64-bit. We do that for example in RISC-V and it's
useful from the tooling perspective.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
Add definition for the Adafruit Adalogger Featherwing. This shield
compatible with the Adafruit Feather family is equipped with an SD card
slot and a PCF8524 RTC.
This work is based on the Adafruit Data Logger shield definition.
Signed-off-by: Philip-Dylan Gleonec <philip-dylan@gleonec.bzh>
Initial support for M5Statck CoreS3 development board.
Signed-off-by: Zhang Xingtao <zhxt@live.cn>
Co-authored-by: Benjamin Cabé <kartben@gmail.com>
Co-authored-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
The Adafruit Feather M4 Express is a compact, lightweight
ARM development board with an onboard mini NeoPixel, 2 MiB
of SPI flash, charging status indicator and user LEDs, USB
connector, 21 GPIO pins and a small prototyping area.
Signed-off-by: Teresa Zepeda Ventura <teresa.zvent@gmail.com>
ST ZIO connector is Arduino Uno compatible. Arduino SPI pins are placed on
D10-D13 pins, where D10 is SPI nCS pin. This pin is connected with PD14 of
STM32U5A.
According to schematics of this Nucleo board [1]:
Due to muxing constrainte, the SPI_NSS is not available as an alternate
on this IO, so this pin is affected with an I/O function to do the Chip
Select
This means that software control of GPIO is needed to make use of this SPI
interface on regular SPI signals on Arduino connector. Reconfigure
SPI1 (used as Arduino SPI) interface to account for that.
Note that previously configured PE12 is only available on ST ZIO and ST
Morpho connectors, not on Arduino connector.
Update documentation as well, which was referencing PA4 as nCS signal (used
on some other Nucleo boards).
[1] https://www.st.com/resource/en/schematic_pack/mb1549-u5a5ziq-c04-schematic.pdf
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
- Sets s26ks512s0 flash write-block-size to correct 256KB.
- Optimizes MCUboot partitions to fit the correct write-block-size.
Fixes#80284
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Clarify that one can simulate equally well the nRF54L10 and L05
variants with this target.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This target simulated is reasonably tested.
Let's stop warning about it being experimental.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Fix compilation error by specifying usart1 to be used for uart-pipe.
Add a board-specific configuration file to disable the console,
so, the usart1 will be used only for bluetooth and to specify
the BT_HCI_TX_STACK_SIZE.
Signed-off-by: Nidhal BEN OTHMEN <nidhal.benothmen@st.com>
Let's fix the sample used in the example. The peripheral_hr and
central_hr are meant to be run with each other.
Let's also use the :zephyr:code-sample: directive to refer to the
samples so we get a link.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
-Update formatting and contents of index.rst for cy8ckit_062s4
-Update formatting and contents of index.rst for cy8ckit_064s0s2_4343w
-Update formatting and contents of index.rst for cy8cproto_062_4343w
-Update formatting and contents of index.rst for cy8cproto_063_ble
-Update formatting and contents of index.rst for xmc45_relax_kit
-Update formatting and contents of index.rst for xmc47_relax_kit
-Change all instances of "PSoC" to "PSOC" for infineon platforms
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
Remove CONFIG_GPIO from defconfigs for Infineon boards.
Applications, drivers will enable GPIO if need.
Added 'select GPIO' from spi/Kconfig.ifx_cat1
Added 'select GPIO' from wifi/infineon/Kconfig.airoc
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Moved uatr6 to common dts for m4
- cm0 uses uart-5 in ver 0.0.0 and uart-5 in ver 1.0.0 (for
using of Arduino headers).
- cm4 by default uses uart-2 (for ver 0.0.0 and ver 1.0.0)
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
This updates the documentation of all the LilyGO boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Flash support for RT1170 EVKB was fixed with cfb7322107 (drivers: flash:
flash_mcux_flexspi: add support for W25Q512NW-IQ/IN). Document this
support in the board page.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Minimum heap pool should be always set for the board
in order to enable internal drivers/subsystems to work.
It is currently not defined for APPCPU due to typo in
board's Kconfig, possibly causing build failures.
Fixes#81218
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Fix missing flash and code partition.
Add missing dts entries and use common partition tables to all related
non-Espressif boards, previously ommited.
Add uart1 node in pinctrl for APPCPU.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
By default, libc malloc allocated area is using all available RAM.
For some yet unknown reason, this conflicts with TF-M resulting in a
Hard Fault before jumping in the non secure application.
For now, define a Libc malloc area defined to 2048 which is the default in
some other typical applications (ARMv7 targets enabling USERSPACE).
Fixes#77847
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Increase target DSI clock frequency for the RT1160, as the DSI
peripheral requires a faster clock to account for the DSI packets that
must be sent outside of video mode frames.
This fix was previously applied for the RT1170, but is also needed for
the RT1160 SOC as they use the same DSI IP.
Fixes#78299
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The CONFIG_PINCTRL is removed from the board's defconfig files.
Drivers which use pin control function should add "select PINCTRL"
in their Kconfig files.
Fixes#78619
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
mdio_enet_nxp driver accesses the registers of its parent node Ethernet MAC
This commit enables this node in mimxrt1062_fmurt6 board's device tree.
This also fixes Issue #80881
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Status and request GPIOs are missing from the edge connector, add those
to fix Thingy53 + nRF7002EB build.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Remove CONFIG_MMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the mmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
mmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_SDMMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the sdmmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
sdmmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
According to the datasheet, the PHY address is 0x1. When changed to this
value the PHY id is correctly read.
Before:
```
[00:00:00.602,000] <err> phy_mii: No PHY found at address 0
```
After:
```
[00:00:00.051,000] <inf> phy_mii: PHY (1) ID 7C111
```
Signed-off-by: Tomáš Juřena <jurenatomas@gmail.com>
The new update of clock device tree make the pll p q r clock
source cannot be choose by other node
This fix add 1 new dts binding for pll out p q r out line
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
I recently found out, that the Ethernet support for the boards Nucleo
H563ZI and STM32H573I-DK is already available but it isn't mentioned
in the "Supported Features" section.
Signed-off-by: Philipp Steiner <philipp.steiner1987@gmail.com>
Let's explicitly mention we are enabling the native_posix entropy
driver for this board (the real nrf54l15dk does not have an entropy
driver in Zephyr yet).
And correct a bit the wording around mbedtls as for the real target we
don't have mbedtls with HW acceleration.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This causes a build error as nRF70 driver running on CPU APP needs this
when SR co-existence is enabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Missed a few keys while moving to the new style twister.yaml file for
the intel_adsp platform. Add those back.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
SOCs using ECC require the SEGGER RTT control block address to be
provided to the tooling, as the SEGGER tools will not scan the memory
range of ECC ram. Add documentation making this clear to boards with
these SOCs.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In preparation of adding a check for dead references, this commit fixes
currently broken zehpyr_file: links.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
To accommodate for some slow tests on up2.
For example: tests/arch/x86/info/arch.x86.info.userspace
Execution time of this test is close to 55s and sometimes
above up to the 60s.
Related issue: #80134
Signed-off-by: Artur Wilczak <arturx.wilczak@intel.com>
Add variant for the coex interface and move the coex interface out
if the wifi/control interface variants.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Exclude the coex interface if the coex variant of the nrf7002eb
is selected instead of adding the interface alongside the
wifi/control interface.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Extended UICR will not be used as its configurations will be merged
with the UICR registers in NVR.
Memory maps changes are needed to align with pre compiled
firmware.
Signed-off-by: Håkon Amundsen <haakon.amundsen@nordicsemi.no>
Signed-off-by: Jonathan Nilsen <jonathan.nilsen@nordicsemi.no>
The Seeed Studio XIAO ESP32S3 Sense board is a board based on the XIAO
ESP32S3 board with a soldered B2B connector that allows to connect
an extension board with a camera sensor, microphone and the sdcard slot.
Signed-off-by: Patryk Biel <pbiel7@gmail.com>
Fixes: #69548
Support extending an existing board with new board variants.
This commit introduces the following changes to allow a board to be
extended out-of-tree.
The board yaml schema is extended to support an extend field which
will be used to identify the board to be extended.
A board 'plank' can be extended like this:
> board:
> extend: plank
> variants:
> - name: ext
> qualifier: soc1
For the rest of the build system this means that there is no longer a
single board directory.
The existing CMake variable BOARD_DIR is kept and reference the
directory which defines the board.
A new CMake variable BOARD_DIRECTORIES provides a list of all
directories which defines board targets for the board.
This means the directory which defines the board as well as all
directories that extends the board.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
What is changed?
Updated the condition thats prevents mpu config for null dereference.
Added a new check so that mpu is configured for null dereference if
devicetree contains a memory-region node with:
- node address starting at 0
- size covered by the node is more than the null dereference page
size (0x400) and
- contains a memory-attr
Why is the change needed?
The check relied on flash base address to align with 0 for
configuring the mpu for null dereference but, a device tree
could have a flash starting at an address other than 0 and
still need the mpu config for null dereference.
The new extra check provides a way to connfigure mpu for
null dereference even if flash base address is not 0.
Note, though this change helps with mpu config for new boards having
flash address other than 0, this change does not change existing
behaviour for existing boards.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
What is changed?
- Added a new mps3 board an555 for the soc corstone310.
The qualifier to build/run application with board mps3/an555 is
`mps3/corstone310/an555` for secure and
`mps3/corstone310/an555/ns` for non-secure.
- Added FVP variant to enable FVP testing with corstone310
and it uses the ARM FVP `FVP_Corstone_SSE-310`.
The qualifier to build/run application with FVP is
`mps3/corstone310/an555fvp` for secure and
`mps3/corstone310/an555fvp/ns` for non-secure.
Why do we need this change?
- This enables FVP support and testing for corstone310.
- A separate FVP variant was added for AN555 because, the TFM board
used for non-secure variant differs for FPGA and FVP.
TFM board `arm/mps3/corstone310/an555` should be used when testing
AN555 with FVP and `arm/mps3/corstone310/fvp` should be used when
testing with AN555 FPGA.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
What is changed?
- Added a new mps3 board an552 for the soc corstone300.
The qualifier to build/run application with board mps3/an552 is
`mps3/corstone300/an552` for secure and
`mps3/corstone300/an552/ns` for non-secure.
- Added FVP variant to enable FVP testing with corstone300
and it uses the ARM FVP `FVP_Corstone_SSE-300_Ethos-U55`.
The qualifier to build/run application with FVP is
`mps3/corstone300/fvp` for secure and
`mps3/corstone300/fvp/ns` for non-secure.
- Note: the qualifier to build/run application with board mps3/an547
is now changed to
`mps3/corstone300/an547` for secure and
`mps3/corstone300/an547/ns` for non-secure.
How is it changed?
- Moved common code from mps3/an547 to corstone300.
- Renamed soc for an547 to corstone300 and added
a new soc corstone300/an552.
Why do we need this change?
- This enables FVP support and testing for corstone300.
- SOC/qualifier for mps3/an547 was renamed to reduce code redundancy
- A separate FVP variant was added for AN552 because, the TFM board
used for non-secure variant differs for FPGA and FVP.
TFM board `arm/mps3/corstone300/fvp` should be used when testing
AN552 with FVP and `arm/mps3/corstone300/an552` should be used when
testing with AN552 FPGA.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
WS25Q512JV can only run at 104MHz at 3.3V, unless the read parameter
bits are changed. Since we don't reprogram these currently, reduce max
frequency to safe value
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The `HCI_SPI` symbol is now automatically selected from devicetree,
removing the need for board specific defaults.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The peer remote device "source_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "sensor_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The ov5640 camera driver now supports both MIPI CSI2 (DPHY) and DVP
modes. It is in MIPI CSI2 mode in this overlay. Add bus-type property
for this. In this mode, data-lanes property is required as well.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The LPC55S36 board has an integrated MCU-Link debug probe, not an
LPC-Link2. Also, it is now possible to directly use the stock CMSIS-DAP
mode with the `linkserver` runner.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
mcxc242 has usb device capability. Add usb to board documentation and
to the yaml file. Enable and configure it in board dts.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
This updates the documentation of all the SiFive boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Element14 boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Cadence boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Franzininho boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the CThings boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Qemu boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the WeAct boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the "others" boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Contextual Electronics boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Rasperry Pi boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the DPTechnics boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Space Cubics boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the SECO boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Qorvo boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Firefly boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Ronoth boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Khadas boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Gaisler boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Croxel boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the EBYTE boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Raytac boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Kincony boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Renode boards to
use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Segger boards to
use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Texas Instruments boards to
use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Synopsis boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Longan boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Silicon Labs boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the bytesatwork boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Blue Clover Devices boards to
use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Aconno boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Atmel boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Witte boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Wemos boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Wurth Elektronik boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the WaveShare boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the VNG boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the VCC-GND boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the UDOO boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Toradex boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Telink boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Technexion boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the TDK boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the StarFive boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the STM32 boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Ruuvi boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the RAK Wireless boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Quicklogic boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Pine64 boards to use
the new `zephyr:board::` directive.
Also drops the "leaflet" image which really isn't adding any value.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Particle boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Panasonic boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the openISA boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Olimex boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the NXP boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Nuvoton boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the MXChip boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the MikroElektronika boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Microchip boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the MakerDiary boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the MadMachine boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the M5Stack boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the innblue boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Infineon boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Holyiot boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Heltec boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the HardKernel boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Google boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the GigaDevice boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Gardena boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Ezurio boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Espressif boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Electronut boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Efinix boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Dragino boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Blues boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the BeagleBoard boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the BBC boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Atmark boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Aspeed boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the AMD boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Ambiq boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Altera boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Alientek boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Analog Devices boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Adafruit boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Actinius boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the 01space boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
The DT node "stimer0" represented two different hardware timers,
RTCC and SYSRTC. Use the correct peripheral names for the nodes.
Add interrupt names and missing interrupt numbers.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
For easier recognition PHYTEC boards have been prefixed with the SoC name.
As the new hardware model includes the SoC and cpu, this prefixing is not
needed anymore. All PHYTEC eval boards have an individual and unique name
and can be found easily via this name.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
For easier recognition PHYTEC boards have been prefixed with the SoC name.
As the new hardware model includes the SoC and cpu, this prefixing is not
needed anymore. All PHYTEC eval boards have an individual and unique name
and can be found easily via this name.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
The nRF54 and nRF92 chips has data cache, which means
the ICMsg and ICBMsg must be configured to follow required
cache alignment of the shared memory.
The `dcache-alignement` needs to be defined for that.
Signed-off-by: Dominik Kilian <Dominik.Kilian@nordicsemi.no>
hwmv2 established a convention that boards live in a folder named after
the vendor prefix.
RAK Wireless boards apparently missed the memo :)
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
For the "References" section to be useful, it needs to include a call to
the target-notes directive, which is the one that actually generates the
list of references made in the current document.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Renamed andestech,plic-sw to andestech,mbox-plic-sw because the mbox node
is based on the PLIC interrupt controller node instead using the plic
hardware directly.
Signed-off-by: Jimmy Zheng <jimmyzhe@andestech.com>
Fixes selection of a symbol that was done in a defconfig file,
when actually it should be done in a Kconfig file as a dependency
for the board
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Updated imx8mm/n/p and imx93 Cortex-A Core supported features in board
yaml file, and also fixed ram size for the board.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Ensured flash size and partition size are specified in bytes
as required by the STM32 QSPI NOR driver.
Signed-off-by: Harry Jiang <explora26@gmail.com>
Update the board cmake to use xsdb runner, If users would like to
use default xsdb.cfg then need to pass the fsbl.elf binary via
--fsbl option when using west flash or twister commands.
Usage:
1) west flash --runner xsdb --elf-file kv260_r5/zephyr/zephyr.elf
--fsbl <path>/fsbl.elf
2) ./scripts/twister -p kv260_r5 --west-runner xsdb --device-testing
--device-serial /dev/ttyUSB0 --west-flash="--fsbl=<path>/fsbl.elf"
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.kedareswara.rao@amd.com>
The default configuration for PINCTRL should not be set with
the other default configurations in .defconfig, instead select
a default value as part of defining the UART driver.
Signed-off-by: Andrew Davis <afd@ti.com>
IS25WP flash chips support 133MHz only when P[6:3] is programmed, which
will not occur during the SFDP probe sequence used in the FlexSPI nor
driver. With the default P[6:3] value, the best frequency supported for
read instruction 0xEB is 104MHz, so set this for all boards using this
flash chip with the FlexSPI nor driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
We now use hwmv2 to list boards instead of relying on twister specific
config files.
One yaml files (twister.yaml for now) will have all the data needed for
all possible targets and variations of a board reusing most of the data
where possible and variations can override the top level data.
Twister keeps track of 'aliases' of boards and identifies that for
example native_sim is the same as native_sim/native, so either names
will be possible in both test yaml files or on the command line,
however, the reporting will always use the full name, so no there is no
confusion about what is being tested/built.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adds a new shield definition for the Analog Devices EVAL-ADXL362-ARDZ
accelerometer shield. This shield provides support for an ADI ADXL362
3-axis accelerometer over an Arduino SPI connector.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Introduce bindings for Series 2 oscillators: HFRCODPLL, HFRCOEM23,
LFRCO and LFXO.
Add clock tree representation in devicetree `clocks` node.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Switch EFR32MG21 to use the device init HAL. This makes the init sequence
the same as the rest of Series 2.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
On Series 2, set the SYS_CLOCK_HW_CYCLES_PER_SEC Kconfig option from
DeviceTree, rather than separately configuring it in board-level
defconfig.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
The DC-DC converter was unconditionally initialized with default
settings on Series 2. Add device tree binding and nodes, and guard
call to init function. Map DT options to config header from HAL.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Enable USART1 that can be used with external periphs via Arduino pins.
LPUART1 can also be used on the same pins.
Tested with tests/drivers/uart_elementary
Signed-off-by: Abderrahmane Jarmouni <git@jarmouni.me>
- add ITCM definitions (for LinkServer) in board.cmake
- update of soc.c to support RAM images (stack pointer)
- doc update
Change applies to both versions of the MIMXRT1170 EVK
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
This updates the documentation of all the Seeed Studio boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Apply this overlay to test RFU_BTN1 and RFU_BTN2 on PCAL6524.
The user buttons RFU_BTN1 and RFU_BTN2 is connected to i.MX 93 GPIO by
default, but can be changed to connect to onboard GPIO expander
PCAL6524. To do this, switch SW1006 to 0000, then switch SW1005 to 0101.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Add include path to nordic/soc/nordic/common where some internal
headers for nordic devices are kept (e.g. dmm.h).
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
- boards: renesas: Add support for agt.
- drivers: counter: Add support for counter driver use agt
- dts: arm: Add support for agt.
- dts: bindings: Add support for agt counter driver.
- soc: renesas: Add support for agt counter driver.
- samples: drivers: counter: alarm: Add support for RA8
This is initial support with only basic functionality for counter
operation on Zephyr using AGT hardware, current support for
count source is limited to LOCO and PCLKB, other count source
like underflow signal external pin or AGTIO from another AGT
channel will be added in later support
Signed-off-by: Ha Nguyen <ha.nguyen.fz@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Configures pins for the SPI instance attached to the Arduino connector
to enable using this board with the eval_adxl372_ardz shield.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Configures pins for the GPIOs attached to the Arduino connector to
enable using this board with the eval_adxl372_ardz shield.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Adds a new shield definition for the Analog Devices EVAL-ADXL372-ARDZ
accelerometer shield. This shield provides support for an ADI ADXL372
3-axis accelerometer over an Arduino SPI connector.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Use EXTRA_CONF_FILE in documentation .rst/.md files,
that replaced deprecated OVERLAY_CONFIG since the Zephyr v3.4 release.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
A bunch of copy-paste mistakes when adding the nRF54L15 DK added stale
references to the Preview DK (PDK).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Current code does no longer support
the non monolithic feature.
Hence, removing unnecessary code.
Signed-off-by: Yassine El Aissaoui <yassine.elaissaoui@nxp.com>
Enabled the MRT at the board level for
mcxn947. Enabled the clocking for the MRT
in the clock control.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Doc and .yaml descriptions shall mention retained_mem
in supported features on affected boards.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Enable the irqstr interrupt controller for the adsp-based
imx8mp.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Enable dma boards/test for S32Z270.
The non-cacheable memory used for DMA tests (chan_blen_transfer and
loop_transfer) is split from the system SRAM.
Signed-off-by: Ha Duong Quang <ha.duongquang@nxp.com>
To enable breakpoints on this board, remove the `dgdb_memory_map disable`,
which is a leftover from early development steps.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Add I2C and SPI configuration to board DTS and mark as supported in YAML.
Also add support for arduino_i2c and arduino_spi.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add I2C and SPI configuration to board DTS and mark as supported in YAML.
Also add support for arduino_i2c and arduino_spi.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
