Support regulator output different voltage as reference to LPADC
the regulator output voltage can be set through property
zephyr,vref-mv
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
Expands driver to cover nRF54L15 features like AIN as GPIO configuration,
new reference voltage, different set of supported gain options.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Update m2l31x.dtsi for adc support and update adc_numaker.c
to support acquisition time in 0~255 ADC ticks.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
This fixes the problem that `adc_raw_to_millivolts` only returns half of
the actual voltage.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Found via static analyis. When `adc_kb1200_start_read` succeeds, no
value is set for `error` so it is still uninitialized when it is
returned.
Signed-off-by: François Baldassari <francois@memfault.com>
Use information encoded in conversion result value to validate it.
Check if MSB bit is set to zero.
Check if channel number included in the result matches channel
number selected for conversion.
Use bitmask to extract converted value instead of math calculations.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
k_thread_name_set() function returns an error if CONFIG_THREAD_NAME is
not enabled which may make the driver not functional.
Fix the issue by adding a check against CONFIG_THREAD_NAME avaliability
before calling k_thread_name_set() function so the driver can operate
properly with CONFIG_THREAD_NAME disabled.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Add configuration of internal refference voltage value so raw ADC
readings can be converted to mV utilizing adc_raw_to_millivolts()
ADC API function.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
The adc_ads1119 driver is unable to overwrite the configuration register,
the chip therefore always works with its default settings. Register access
macros are fixed by this commit.
Fixes: #70091
Signed-off-by: Jan Kubiznak <jan.kubiznak@deveritec.com>
Rename ad5592 files in dts, driver and include to ad559x and add support
for I2C bus which is required for AD5593.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add a blank define for the case where DMA channels are defined in ADC node
of the dts but STM32_ADC_DMA is not enabled. Otherwise compilation fails.
Also fix the way the DMA channel is configured by using a standard DT
macro, otherwise it doesn't work for dma-v2bis DMA types.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Added the STM32G0X SOC series to the list of SOC that need to disable the
ADC while setting the oversampling bits to prevent writing over the
CKMODE bits.
Signed-off-by: Alexandre Poizat <apoizat@kalrayinc.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69129
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69133
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69132
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69131
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69130
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Do not disable the ADC after the end of the measurement to avoid systematic
enabling which is time-consuming in case the configuration is unchanged.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Prevents the system to go in Suspend to RAM low power mode while ADC
measurement is in progress.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
For series that have two sampling time common channels, only one was used.
This commit add the support for the second one. The first two different
acquisition time values are used for the sequence and all further values
must match either of them, otherwise generating an error.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
The TLA2021 driver depends on it's i2c controller and therefore needs
to be initialized later. ADC_INIT_PRIORITY by default equals
KERNEL_INIT_PRIORITY_DEVICE which should be used by independent devices.
Using this by default causing projects to fail where this driver is
enabled implicitly through board configuration and the priority is not
explicitly set.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Several STM32 variants include both shared IRQs for some ADCs and
separate IRQs for others (for example, STM32G473 has 5 ADCs, ADC1 and
ADC2 share one IRQ while ADC3, ADC4 and ADC5 each have unique
IRQs). The STM32 ADC driver however previously only supported either
separate IRQ lines for each operational ADC in the devicetree or a
single shared IRQ for all operational ADCs in the devicetree which
prevented all ADCs from being usable at the same time when the variant
contained a mix of both shared and separate ADC IRQ lines (only either
all the shared or all the separate and one of the shared might be used
at most for one application).
To allow for all ADCs in an STM32 variant to be usable in a single
application, generate an ISR and initialization function for each
unique IRQn as defined in the devicetree and give the task of
initialization to the first ADC which connects to that particular
IRQ. Each ISR function will generate code to call the ISR for each ADC
associated with that IRQn as was previously done for
CONFIG_ADC_STM32_SHARED_IRQS, allowing an ISR to be shared for the
ADCs sharing an IRQ while simultaneously providing separate ISRs for
each IRQ. Thus, the only information required to have ADCs either
share an ISR or not is provided by the devicetree.
Signed-off-by: Michael R Rosen <mrrosen@alumni.cmu.edu>
The current driver initializes the IADC with the default configuration
(IADC_INITSINGLE_DEFAULT), which aligns the data to the right.
To correctly read the 12-bit sample, it should be masked from the right
instead.
Signed-off-by: Paulo Santos <pauloroberto.santos@edge.ufal.br>
When using one of the internal channels (die_temp, vbat, vref) the
channels are enabled in the individual drivers and disabled again
whenever an adc conversion is complete.
This creates a race condition if the ADC is used from multiple threads.
This commit moves the disabling of the channels to the individual
drivers.
Signed-off-by: Brian Juel Folkmann <bju@trackunit.com>
Updated API version enables multi-instance GPIOTE driver.
Additionally obsolete symbol that was used to specify
API version in the past was removed.
Affected drivers have been adjusted and appropriate changes
in affected files have been made.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Turning on clock via clock controller and
resetting ADC device via reset controller on initializing.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Configure the sw trigger just after calibration
So the conversion can start on regular channel on the
software control bit.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds support for more STM32 CPUs that has
a different DMA interface. This was tested only for
the nucleo_l476rg.
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Previously the STM32 DMA driver was dependent on a very specific
name for the DMA in the DTS. This hidden requirement has caused
a bit of confusion. This commit changes the driver to instead
always use the first DMA listed in the ADC node's dma property.
Should fix: #65387
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Do not enable subsystem/driver shell modules by default and stop abusing
CONFIG_SHELL_MINIMAL, which is internal to the shell subsystem, to decide
when to enable a driver shell.
The list of shell modules has grown considerably through the
years. Enabling CONFIG_SHELL for doing e.g. an interactive debug session
leads to a large number of shell modules also being enabled unless
explicitly disabled, which again leads to non-negligible increases in
RAM/ROM usage.
This commit attempts to establish a policy of subsystem/driver shell
modules being disabled by default, requiring the user/application to
explicitly enable only those needed.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Affected CONFIG_ADC_ADS114S0X_GPIO=y build.
register_addresses was wrong type for
ads114s0x_write_multiple_registers()
Signed-off-by: Nick Ward <nix.ward@gmail.com>
Move the syscall_handler.h header, used internally only to a dedicated
internal folder that should not be used outside of Zephyr.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix the data acquisition thread function signatures to avoid a stack
corruption on thread exit.
Fixes#62637
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Fix the problem not apply pinctrl eventhough the config is defined.
In practice, the setting is equals to soc default.
So, there is no apparent change in behavior.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
"const k_tid_t" is "struct k_thread * const" and not "const struct
k_thread *" as the code may be assuming. Just drop it.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Replace Nuvoton NPCX series definitions with new Kconfig definitions in
the npcx drivers. The benefit of this approach is that we won't touch
the npcx driver sources again during introducing a new npcx series next
time.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The macro K_THREAD_STACK_MEMBER has actually been deprecated
since v2.4.0 in the macro doxygen description, but it was
never marked with __DEPRECATED_MACRO. Since this was being
used in various drivers, make it follow the deprecation
process.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
CONFIG_NOCACHE_MEMORY is a valid way of declaring buffers in
nocache regions. Consider them valid in the STM32 ADC driver
nocache check.
Copied from commit 818aa2d
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
For all STM32 ADC that use common sampling times, there is a check made to
ensure that all channels of a sequence use the same sampling time.
The value was not reset between reads, resulting in error if two
consecutive sequences used different values.
This commit adds a reset of this value once read is done.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Remove CHANNEL_COUNT limit used to check the channel bitmask.
This value was not applicable on STM32L1 where channel can go up to 31.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
On some STM32 families (such as F4), temperature and Vbat sensor share the
same ADC channel, which can lead to conflict when reading them, and wrong
measurement can follow.
To alleviate this problem, this commit moves the setting of the common
path internal channel to the sensor drivers themselves instead of doing
it in the ADC driver.
The teardown is still done in the ADC driver, systematically, instead of
channel by channel (which has the same result).
By moving this logic in the sensor drivers, the properties temp-channel,
vbat-channel and vref-channel becomes useless and are thus removed.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add phandle prop to reference any regulator that must
be enabled in order for the LPADC to function as intended.
Change LPADC driver to use this property if present.
LPADC on LPC55S36 depends on VREF peripheral, enable for this platform.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This is the final step in making the `zephyr,memory-attr` property
actually useful.
The problem with the current implementation is that `zephyr,memory-attr`
is an enum type, this is making very difficult to use that to actually
describe the memory capabilities. The solution proposed in this PR is to
use the `zephyr,memory-attr` property as an OR-ed bitmask of memory
attributes.
With the change proposed in this PR it is possible in the DeviceTree to
mark the memory regions with a bitmask of attributes by using the
`zephyr,memory-attr` property. This property and the related memory
region can then be retrieved at run-time by leveraging a provided helper
library or the usual DT helpers.
The set of general attributes that can be specified in the property are
defined and explained in
`include/zephyr/dt-bindings/memory-attr/memory-attr.h` (the list can be
extended when needed).
For example, to mark a memory region in the DeviceTree as volatile,
non-cacheable, out-of-order:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_VOLATILE |
DT_MEM_NON_CACHEABLE |
DT_MEM_OOO )>;
};
The `zephyr,memory-attr` property can also be used to set
architecture-specific custom attributes that can be interpreted at run
time. This is leveraged, among other things, to create MPU regions out
of DeviceTree defined memory regions on ARM, for example:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-region = "NOCACHE_REGION";
zephyr,memory-attr = <( DT_ARM_MPU(ATTR_MPU_RAM_NOCACHE) )>;
};
See `include/zephyr/dt-bindings/memory-attr/memory-attr-mpu.h` to see
how an architecture can define its own special memory attributes (in
this case ARM MPU).
The property can also be used to set custom software-specific
attributes. For example we can think of marking a memory region as
available to be used for memory allocation (not yet implemented):
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_NON_CACHEABLE |
DT_MEM_SW_ALLOCATABLE )>;
};
Or maybe we can leverage the property to specify some alignment
requirements for the region:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_CACHEABLE |
DT_MEM_SW_ALIGN(32) )>;
};
The conventional and recommended way to deal and manage with memory
regions marked with attributes is by using the provided `mem-attr`
helper library by enabling `CONFIG_MEM_ATTR` (or by using the usual DT
helpers).
When this option is enabled the list of memory regions and their
attributes are compiled in a user-accessible array and a set of
functions is made available that can be used to query, probe and act on
regions and attributes, see `include/zephyr/mem_mgmt/mem_attr.h`
Note that the `zephyr,memory-attr` property is only a descriptive
property of the capabilities of the associated memory region, but it
does not result in any actual setting for the memory to be set. The
user, code or subsystem willing to use this information to do some work
(for example creating an MPU region out of the property) must use either
the provided `mem-attr` library or the usual DeviceTree helpers to
perform the required work / setting.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add all available instances of the ADC series
MAX11102-MAX11117 to the ADC shell.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Remove `threshold-reg-offset` DT property and implement them with static
inline functions in `reg_def.h`
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add multi-device support in npcx adc driver since there is more than one
adc module in npcx4 series. And each adc's reference voltage might be
different, this CL introduces the `vref-mv` prop. to select its own
reference voltage.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Signed-off-by: Kate Yen <htyen@nuvoton.com>
Now that everything is in place, the prescaler value picked from dts is
used to properly configure the clock.
The code is moved into its own function.
There are four main cases:
- F1 and F37x don't have prescaler (in ADC register) so nothing is done.
- F0 only has individual registers.
- C0, G0, L0, WB1x and WL have both invidual and common registers. The
individual one is used to define either synchronous mode with its
prescaler, or asynchronous mode. The common one is only used to store
the value of the asynchronous prescaler.
- All others only have a common register where both the mode and the
prescaler is stored.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Get the STM32 ADC prescaler data from dts to create the appropriate LL
macro to use for the ADC clock.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
This adds support for the max1125x (max11254, max11254)
family of spi adc devices.
Signed-off-by: Mustafa Abdullah Kus <mustafa.kus@sparsetechnology.com>
To allow the ADC API unit test to skip tests for non-implemented
features, return -ENOTSUP.
Signed-off-by: Eric Holmberg <eric.holmberg@northriversystems.co.nz>
Fixes#61401
The ADS1x1x driver has a bad habit of assuming i2c operations will
always suceed - this fixes the two worse cases in the code I could
identify (there may yet be more).
* During initial ADC setup, if either of the two I2C operations
(read or write) fails, raise the error immediately to the caller
rather than letting it fall through to the acquisition thread.
This ensures that we only ever attempt to give a result that was
definitely connected to our attempt to start the capture.
* If the acquisition thread encounters an I2C error, raise the error
but do not terminate the aquisition thread. This ensures the
application can attempt to fix the condition that caused the I2C
error and try again.
Signed-off-by: Chris Collins <kuroneko@sysadninjas.net>
Add support ADC SAR for NXP S32. ADC SAR diver
support 3 group channels (precision, standard
and external), run normal trigger in oneshot
conversion mode with 2 callbacks normal end
of conversion and normal end chain callbacks.
An instance only run on 1 group channel and
1 kind of callback at the same time.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Refactor the ESP32 target SOCs together with
all related boards. Most braking changes includes:
- changing the CONFIG_SOC_ESP32* to refer to
the actual soc line (esp32,esp32s2,esp32s3,esp32c3)
- replacing CONFIG_SOC with the CONFIG_SOC_SERIES
- creating CONFIG_SOC_FAMILY_ESP32 to embrace all
the ESP32 across all used architectures
- introducing CONFIG_SOC_PART_NUMBER_* to
provide a SOC model config
- introducing the 'common' folder to hide all
commonly used configs and files.
- updating west.yml to reflect previous changes in hal
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Previously, only a single type of ADCs was always available
in the ADC shell. This change enables the usage of the ADC
shell for different ADC types at the same time.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Depending on the ADC implementation it might happen that
the driver is waiting on an external interrupt. If this interrupt
gets lost, for instance due to a race condition with an external
port expander, the system will get stuck.
Making this configurable allows the user to recover from such
an error.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Only 12-bit resolution is currently available in the driver,
and each of the 16-bit samples store the actual data
aligned to the left.
A sample should be shifted 4 bits to the right to allow
proper interpretation.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
When reading multiple ADC channel in parallel, an ADC command chain will be
build. This is similar to a linked list, as every command references the
next command.
Before this patch every ADC command after the first, would always reference
this initial command. So that during execution only two commands (the last
and first) would be executed which resulted in readout of only two analog
values. As Zephyr expected more to come in, the `read_adc` function would
block endlessly.
The patch fixes the behaviour and allows a correct chain to build up.
Signed-off-by: Elisabeth Friedrich <auxsys@flowerpot.me>
The adc_driver_api structure provides .ref_internal
which previously was unset.
Now .ref_internal is set to the proper value.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
The device passed to the DMA callback is the DMA device. Instead use
the ADC device available in the private data.
Signed-off-by: Brett Witherspoon <brett@witherspoon.engineering>
This adds a driver for Texas Instruments Cost-Optimized, Ultra-Small,
12-Bit, System-Monitoring ADCs. Currently only TLA2021 is supported,
TLA2022 and TLA2024 may follow based on this driver.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
This adds a few line use zephyr_syscall_header() to include
headers containing syscall function prototypes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The adc-shell uses a hardcoded list of defines to check whether it should
throw a compile-time error. The ADS1119 and ADS1112 driver both support
the APIs needed by the shell, so this commit enables support for them in
the hardcoded support list.
Signed-off-by: Jordan Montgomery <jordan.montgomery@getcruise.com>
This PR adds a custom driver for the ADS1112 ADCs. Unlike ADS1113/4/5
family served by the ADS1x1x driver, the ADS1112 does not use an address
pointer to address config registers. Instead, there is only one writable
register and all i2c writes will set it. The registers resemble the
ADS1119 device, but config bitmap is different, include a distinct data
rate table, gain table, and input multiplexing table. There is also not a
status register to be monitored with the ADS1112, as it uses config bit 7
for the same purpose instead of a separate register.
The driver was tested on hardware using the ADC shell interface. Manual
probing validated the voltages for the MUX_SINGLE configs at datarate 15
in CM_SINGLE. Higher gains were not tested and CM_CONTINUOUS is not
supported in this initial implementation.
The new driver has also been added to the existing ADC test using adc_emul
for completeness.
Origin: original
License: Apache 2.0
Purpose: Adding support for ADS1112 ADCs
Signed-off-by: Jordan Montgomery <jordan.montgomery@getcruise.com>
The pga enum internal reference voltage and gain values
were fixed in the code, but a comment was forgotten to be
updated. Correct the comment to match how the code uses
the enum.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Add a property to the ADC channels which allows the configuration
of the current source pin.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Define two macros for calibration and oversampling for STM32 series that
possess these features, and use these macros instead of a list of series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Rework oversampling by creating a const table containing possible
oversampling values and using this table instead of switch case.
Also disable ADC for all series before setting oversampling.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Renesas Renesas SmartBond(tm) have two ADC blocks:
GPADC and SDADC.
This change adds drivers for both.
Each ADC supports only one channel setup, drivers allow
to have multiply channels in sequence. Switching
between ADC sources in done in software.
GPADC has 10 bit resolution (accuracy can be increase
with oversampling). Values up to 3.6V can be measured
on selected pins. V30 and VBAT1 can also be measured.
SDADC has 14 bit resolution and can take measurements
from 8 pins (single of differential) and VBAT.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Several sections of the STM32 ADC driver are #ifdef by a combination of the
same SOC defines that share similar IPs. These are F2/F4/F7/L1, and
F1/F37x.
Each of these combinations is now replaced by a specific compatible, which
makes the code a bit lighter and more succinct.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add ifdef around some functions that don't exist for STM32F37x (ADC_V2_5)
like it is done for STM32F1x.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Inverts the logic of some #ifdef, replacing lists of newer series by a
list of NOT older series. This makes it shorter, and more future-proof as
future series are more likely to work out of the box, without need to
manually add a new define in each place.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Some STM32 families that need to check the ADRDY flag after enabling the
ADC were not doing it. The #ifdef has been updated to fix that.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Use the new dts properties for sampling time in the STM32 ADC driver:
- Get the sampling time from dts
- Remove all sampling time macro concatenation.
- Simplify/refactor setting of sampling time
- Check that sampling time is the same for all series using common channel
This also fixes a few cases where wrong sampling times were used for an
ADC instance (like ADC4 on U5, or ADC3 on STM32H723).
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Renamed CONFIG_ADC_GECKO to CONFIG_IADC_GECKO to eliminate confusion
between the Incremental ADC found on series 2 silabs gecko MCUs, and the
ADC found on earlier gecko series.
Signed-off-by: Jared Baumann <jared.baumann8@t-mobile.com>
Make use of positive status values in the DMA callback to pass
info to the DMA client after a successful DMA operation.
A completed DMA transfer uses the status 0 while a reached
water mark uses the status 1.
Signed-off-by: Cyril Fougeray <cyril.fougeray@worldcoin.org>
SPI configuration did not set bit ordering or more importantly the clock
polarity which seemed to be misconfigured. Setting this corrects one more
quirk when working with this part on the TDK Robokit1
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
To be consistent with the current NXP clocking scheme,
move the LPADC clocking code to the SOC files where
all of the other peripheral clocking is done.
Also remove any other SOC-specific code to the
respective SOC file and out of this driver.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Code for power level property was accidentally
removed by accident from driver in commit 9921c59f40
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Simplify the STM32 ADC driver code by using the new ADC resolutions
property in dtsi files.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
- Remove build asserts in favor of DT enums
- Remove power level property since it is unused by SDK
- Correct voltage ref value in DT to correspond to
chip specific values documented in reference manuals
instead of corresponding to SDK enum names.
- Fix SOC devicetrees affected by these changes.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
port commit f7f47dc to stm32h5
Without this fix, ADC driver will hang when reading internal channels.
Signed-off-by: Brian Juel Folkmann <bju@trackunit.com>
The MCUX platform always uses pinctrl, there's no need to keep extra
macrology around pinctrl. Also updated driver's Kconfig options to
`select PINCTRL` (note that some already did).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit adds the Gecko IADC driver and support for it to the
efr32bg_sltb010a board.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
Move semicolon from end of DT_INST_FOREACH to DEVICE_DT_INST_DEFINE
to make multi-instancing possible. This caused some problems with
CI after adding adc node to native_posix dts.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Remove all init functions that do nothing, and provide a `NULL` to
*DEVICE*DEFINE* macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The below is the unit test result for the driver and kernel of
it82xx2_evb board.
GPIO/gpio_basic_api: PASS
I2C/i2c_api: PASS
Flash: PASS
UART/uart_basic_api: PASS
PWM/pwm_api: PASS
WDT/wdt_basic_api: PASS
KSCAN/kscan_api: PASS
kernel/sched/schedule_api: PASS
kernel/sched/preempt: PASS
kernel/timer/timer_api: PASS
kernel/sleep: PASS
ADC/adc_api: PASS.
ADC note: conversion time~=61.6us
sample time delay~=60us
wait voltage stable time~=202.8us
Set sampling time to 500us will pass for ADC test.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
MISRA Rule 5.7 requires uniqueness of tag identifiers. Shell is
frequently problematic because many code uses `const struct shell
*shell`. This causes CI noise every time one of these shell files is
edited, so let's update all of them with `const struct shell *sh`
instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
add support for async call and repeat sample test
1. change the DMA req to 2 byte each
2. increase the buffer pre-dma
3. add protection on invalid buffer
depends on: PR #56104
fixing: issue #56070
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Removes a workaround that was required while there was a bug in
upstream STM32 HAL drivers where the oversampling was not set
correctly in all cases. This has since been fixed, and also
added to the Zephyr STM32 HAL.
The upstream issue:
https://github.com/STMicroelectronics/STM32CubeH7/issues/177
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
The init infrastructure, found in `init.h`, is currently used by:
- `SYS_INIT`: to call functions before `main`
- `DEVICE_*`: to initialize devices
They are all sorted according to an initialization level + a priority.
`SYS_INIT` calls are really orthogonal to devices, however, the required
function signature requires a `const struct device *dev` as a first
argument. The only reason for that is because the same init machinery is
used by devices, so we have something like:
```c
struct init_entry {
int (*init)(const struct device *dev);
/* only set by DEVICE_*, otherwise NULL */
const struct device *dev;
}
```
As a result, we end up with such weird/ugly pattern:
```c
static int my_init(const struct device *dev)
{
/* always NULL! add ARG_UNUSED to avoid compiler warning */
ARG_UNUSED(dev);
...
}
```
This is really a result of poor internals isolation. This patch proposes
a to make init entries more flexible so that they can accept sytem
initialization calls like this:
```c
static int my_init(void)
{
...
}
```
This is achieved using a union:
```c
union init_function {
/* for SYS_INIT, used when init_entry.dev == NULL */
int (*sys)(void);
/* for DEVICE*, used when init_entry.dev != NULL */
int (*dev)(const struct device *dev);
};
struct init_entry {
/* stores init function (either for SYS_INIT or DEVICE*)
union init_function init_fn;
/* stores device pointer for DEVICE*, NULL for SYS_INIT. Allows
* to know which union entry to call.
*/
const struct device *dev;
}
```
This solution **does not increase ROM usage**, and allows to offer clean
public APIs for both SYS_INIT and DEVICE*. Note that however, init
machinery keeps a coupling with devices.
**NOTE**: This is a breaking change! All `SYS_INIT` functions will need
to be converted to the new signature. See the script offered in the
following commit.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
init: convert SYS_INIT functions to the new signature
Conversion scripted using scripts/utils/migrate_sys_init.py.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
manifest: update projects for SYS_INIT changes
Update modules with updated SYS_INIT calls:
- hal_ti
- lvgl
- sof
- TraceRecorderSource
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
tests: devicetree: devices: adjust test
Adjust test according to the recently introduced SYS_INIT
infrastructure.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
tests: kernel: threads: adjust SYS_INIT call
Adjust to the new signature: int (*init_fn)(void);
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
We get compile warnings of the form:
error: converting the result of
'<<' to a boolean; did you mean
'((__aeabi_ctype_table_ + 1)[(byte)] << 28) != 0'?
[-Werror,-Wint-in-bool-context]
if (!isprint(byte)) {
^
Since isprint (and the other is* functions) return an int, change check
to an explicit test against the return value.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
