This macro is defined in a few places which leads to macro redefinition
error e.g. when compiling prometheus network sample for NPCX boards.
Provide one definition of IS_BIT_SET() in util_macro.h to fix the
problem.
Signed-off-by: Patryk Duda <patrykd@google.com>
Move the instance pointer, which is a constant value, into a dedicated
config structure. At the same time, remove the type casting macros as
this pattern has been removed from the tree for some years now.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The STM32 IWDG is a single channel watchdog, and therefore should be
returning `-ENOMEM` when a user attempt to install additional timeouts,
instead of overwriting previous values.
Signed-off-by: Jordan Yates <jordan@embeint.com>
the following implementations are added:
- set cyclic variable to handle circular/normal mode :
enable dest/source_reload_en variable to set CIRC bit to 1 for RX or TX.
- DMA_STATUS_COMPLETE(0), DMA_STATUS_BLOCK(1) macros to handle half
and full irq
- add ASYNC_UART_STATUS_TIMEOUT(3) macro to work with default mode
- add status input in uart_stm32_dma_rx_flush function to handle
async events depending on the mode we are in.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
co-authored-by: Cyril Fougeray <cyril.fougeray@worldcoin.org>
Mostly a revert of commit b1def7145f ("arch: deprecate `_current`").
This commit was part of PR #80716 whose initial purpose was about providing
an architecture specific optimization for _current. The actual deprecation
was sneaked in later on without proper discussion.
The Zephyr core always used _current before and that was fine. It is quite
prevalent as well and the alternative is proving rather verbose.
Furthermore, as a concept, the "current thread" is not something that is
necessarily architecture specific. Therefore the primary abstraction
should not carry the arch_ prefix.
Hence this revert.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The bus recovery feature utilizing bit-bang operations, which sends
SCL clock pulses to recover the bus and checks if the line is down.
Upon recovery, it disables the system test register before resuming
the transactions.
Signed-off-by: Dhruv Menon <dhruvmenon1104@gmail.com>
The OMAP I2C provides support for I2C serial interface on TI K3 series.
It is compatible with Philips I2C physical layer.
The commit includes:
Zephyr i2c api implementation
Polling Mode
Signed-off-by: Dhruv Menon <dhruvmenon1104@gmail.com>
The dma callback functions were written in a very confusing way, clean
them up, and this change also saves some bytes of ROM.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
move copy pasted code into common spot for when there is an invalid
configuration passed to the config function
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
There's no need to put an if before i2s_purge_stream_buffers,
because this is handled already by the boolean values entered to the
function
Also remove the inline of the function, which allowed the compiler to
make optimizations and save some bytes.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Put DT_DRV_COMPAT at top of file by custom
Consolidate logging macros
Clean up checks and use build assert
Remove header file which was not necessary
Remove unnecessary forward declarations
Fix the type of the stream state to be more precise, it is used as the
enum i2s_state type. This requires handling all the enum cases in switch
statements
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Move the cmake file of OSAL to it's own repo and build as a standalone
library, this is porting friendly.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The "nm_bsp_reset" is used to apply a hard reset to the WINC board by
setting CHIP_EN and RESET_N signals low,then after specific delay
the function will put CHIP_EN high then RESET_N high.
reset-gpio is however defined as active low , causing this function
to hold the wifi module in reset.
Signed-off-by: Andreas Ålgård <aal@ixys.no>
When CAN is used, HSFLL frequency must >= AUXPLL frequency. Make sure to
send a request to the HSFLL clock instance.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Instead of assuming that an individual axis must contain all
data-values. Additionally, for determining that there's XYZ data, all
three channels must be present in the header.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
For the supported channels, instead of just allowing 3-axis data being
printed out, allow individual channels to be processed (e.g: accel_x,
gyro_y, etc).
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Wait until the typical time that the sample would be ready before
starting to poll the status register.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Rename _XFR_.*BITS and _WRITE_ONLY_ABSENT according to MISRA-C standard
rules 21.1 and 21.2 (Zephyr rules 121 and 122). For details see Zephyr
coding guidelines in table "Main rules".
Signed-off-by: Stephan Linz <linz@li-pro.net>
Use a string for the xfr-min-bits property over an integer value, as this
significantly improves the readability of the MIPI DBI SPI device binding.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Updated various device definition macros to use the DT_INST variants for
consistency and improved readability.
Signed-off-by: Dong Wang <dong.d.wang@intel.com>
Request fast global domain to run at 320 MHz during fast UARTE
activity. As request is asynchronous it cannot be called from
an ISR. Due to complexity to handle that without device runtime
power management a requirement is added so that if fast UARTE
is used device runtime PM must be enabled. Clock is request
and released in PM resume and suspended actions which in case
of fast UARTE are only called from thread context.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add requesting for global HFSLL when fast instance TIMER (e.g.
TIMER120 in nrf54h20) is used.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
- Bring macro defined of RA8 in flash_hp_ra.h to device tree
- Change to use irq_lock instead of semaphore for code flash
- Modify and add conditions to check and make decision to perform
action at last block.
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Signed-off-by: Tran Van Quy <quy.tran.pz@renesas.com>
This implements to generate the MAC address of the device UUID.
The UUID is hashed to reduce the size to 3 bytes.
Ideas taken from eth_nxp_enet.c
Adding dependencies on: HWInfo and CRC
Signed-off-by: Adib Taraben <theadib@gmail.com>
Fixes issue introduced in #76460
The previous code attempted to detect whether TMAG5273 or TMAG3001 was
connected based on DEVICE ID register. This doesn't work as the bits that
denote the version on one part are undefined on the other part, and cannot
be relied on to be zero.
This commit adds a TMAG3001 compatible which (for now) is just derived from
the TMAG5273 compatible. This allows TMAG3001 to be specified directly in
the DT. The driver code is updated to support both compatibles.
Signed-off-by: Yiding Jia <yiding.jia@gmail.com>
The three sensor channels listed below were recently added by the commit
9471df95a5:
- SENSOR_CHAN_GAME_ROTATION_VECTOR
- SENSOR_CHAN_GRAVITY_VECTOR
- SENSOR_CHAN_GBIAS_XYZ
Theses channel names are missing and causes a system crash if the
SENSOR_LOG_LEVEL is set to DEBUG.
Also, the two sensor attributes SENSOR_ATTR_GAIN and SENSOR_ATTR_RESOLUTION
were added by the commit f849140de7.
This adds these missing channel and attribute to the list of names in the
sensor shell.
Signed-off-by: Gaël PORTAY <gael.portay@rtone.fr>
Update the driver to take the "vrefint-cal-resolution" property into
account when performing the calculations.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
The previous re-organization has the zephyr-keep-sorted defines
missing. Add them for the I2C drivers and targets. Also
moved lines to fix out-of-order violations.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
After writing option bytes, force them to be loaded. Failing to perform
this step means the values are never applied and not actually written
to non-volatile memory.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Fixes issue #83555, where UART transmit operations fail in Zephyr
sysbuild projects using MCUboot and the asynchronous UART API
(`CONFIG_UART_ASYNC_API=y`) on SAM0 devices such as the
ATSAMC21G18A.
The issue occurs because the DMA controller is not reset during
initialization, causing `BASEADDR` and `WRBADDR` registers to retain
MCUboot's configuration. This prevents the application from reconfiguring
these registers to its own RAM addresses, leading to UART transmit
timeouts and triggering the `UART_TX_ABORTED` callback.
This patch resolves the issue by resetting the DMA controller during
initialization in `dma_sam0.c`. The following actions are performed:
- Disables the DMA and CRC modules.
- Applies a software reset to ensure a clean state for reconfiguration.
With this change, UART transmit operations work as expected, improving
stability and compatibility between MCUboot and the application.
Signed-off-by: Tristen Pierson <tpierson@electrohire.com>
This is a squash of all the groundwork needed to
get a functioning driver for the DS3231 with the RTC API.
Signed-off-by: Gergo Vari <work@gergovari.com>
first check if the chip has a hosh module to futher filter MAC addresses
if not then enabling the pass through for all multicast protocols
Signed-off-by: Adib Taraben <theadib@gmail.com>
Use the same Kconfig for all drivers to configure if the FCS bytes
(checksum) should be included in the packets passed to L2.
The description is slightly reworded to make clear that it does not
only affect the length, but the packet content itself.
Signed-off-by: Martin Jäger <martin@libre.solar>
The parameter provided to the `BIT()` macro must be checked so that
the shift operation does not overflow the variable.
Fixes#81990
Signed-off-by: Martin Jäger <martin@libre.solar>
The osal apis spinlock - take, release and bus qspi sleep
are trying to use ops after deinit. So removing osal deinit
for temporary workaround.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Add variable network configuration control into the driver to optimize
RAM usage by default. The pool sizes are default, and tuning is left to
the applications or samples.
Signed-off-by: Triveni Danda <triveni.danda@nordicsemi.no>
Update the context state parameters when the context is already locked.
This allows changing the callback information for asynchronous
operations while the context is locked.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Do not unlock CR at the end of initialization.
The lock mechanism is to protect unwanted registers modifications due to
software bugs. There is no point in leaving the registers unlock once
the driver is initialized.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Currently, the uart_wch driver only supports the polling API.
This patch introduces bindings for the interrupt-driven API.
Signed-off-by: Paul Wedeck <paulwedeck@gmail.com>
When attaching a device, it should look up if the dynamic addr is
already attached only, and not by the static addr.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
For ENTDAA, BCR and DCR is always transmitted back up to the controller.
When `i3c_bus_init` is done, it does the ENTDAA then it would get the
basic info would get the BCR and DCR again. This was rather reduntant.
This now splits it up so there is a function called
`i3c_device_adv_info_get` which gets the mrl, mwl, getcaps, and the
mxds. `i3c_device_basic_info_get` now only just gets the bcr and dcr.
There is also an inline function called `i3c_device_info_get` which
will get everything.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The winstream code itself is reasonably generic, but the console
integration was written to the intel_adsp memory window driver only,
as that was the only consumer.
Add an alternative that allows the winstream to be pointed to by a
linker symbol instead. The platform layer is responsible for putting
it where it needs to go.
Also includes a 20-byte "descriptor" recodr (with a very large magic
number) in the binary that points to the winstream, for the benefit of
external tooling that needs to find it at runtime.
Signed-off-by: Andy Ross <andyross@google.com>
The CMD_BLANK_CHECK can return errors when the flash is readable, and
should only be used after programming, not in is_area_readable(). From
the LPC55S69 datasheet: "As cells age and lose charge, a correctly
programmed address will fail this check, while still being able to be
read successfully for the remaining duration of the data retention time."
Signed-off-by: Derek Snell <derek.snell@nxp.com>
Add support for STM32H757 SoC, which shares its design
with STM32H747 with added cryptography peripherals.
Signed-off-by: Grzegorz Runc <g.runc@grinn-global.com>
Add a non-configurable option which drivers can select to indicate that
they do not support callbacks on watchdog expiry.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The Atmel counter driver requires a valid pinctrl list to initialize.
This relax this condition since the timer can be used as general purpose
timer, which may not require a pin associated with the timer unit.
Fixes#83509
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
Add the Sensor Fusion Low Power (SFLP) FIFO streaming capability,
using RTIO. The decode function is now aware of parsing following FIFO
tags:
- LSM6DSV16X_SFLP_GAME_ROTATION_VECTOR_TAG
- LSM6DSV16X_SFLP_GYROSCOPE_BIAS_TAG
- LSM6DSV16X_SFLP_GRAVITY_VECTOR_TAG
To activate SFLP the user should put in DT the proper configuration.
For example, to activate a 60Hz SFLP FIFO batching rate of game rotation
vector, gravity vector and gbias components, the user should add in DT
the following:
sflp-odr = <LSM6DSV16X_DT_SFLP_ODR_AT_60Hz>;
sflp-fifo-enable = <LSM6DSV16X_DT_SFLP_FIFO_GAME_ROTATION_GRAVITY_GBIAS>;
Signed-off-by: Armando Visconti <armando.visconti@st.com>
In case I3C IBI interrupt is not used do not skip reading the status
register, otherwise the interrupt event will not get cleared.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Align all sensor drivers that are using stmemsc (STdC) HAL i/f
to new APIs of stmemsc v2.8
Requires https://github.com/zephyrproject-rtos/hal_st/pull/24
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Low power mode for non-asynchronous API case is only available when
RX is not used (RX pin is not defined). In that case TX starting
function was using uarte_enable_locked() which tracks if UARTE is
used by TX or RX and TXSTOPPED interrupt was disabling UARTE
unconditionally. Because of that following attempt to TX start
was assuming that UARTE is already enabled when it was disabled.
Fixing it by using uarte_disable_locked function in TXSTOPPED
handling.
Code reordering was required to make uarte_disable_locked()
available earlier.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The get_frame_count() API must return the number of frames in FIFO
for a given channel type, and not the total number of generic FIFO
frames. This API may be also re-used in the decoder routine when
the timestamp baseline is adjusted.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Address issue where the timing source is not stopped upon step completion
and not adjusting the actual position after performing a step.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Adds a fallback for the dual-edge-step property in the step dir common
code. Without this drivers using the common code would have to declare the
dual-edge-step property so it can default to false when not set, even if
the IC does not support adjusting it.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
The status variable stores the return value of `net_recv_data`, which
is an `int` and may be negative.
Signed-off-by: Martin Jäger <martin@libre.solar>
Adds a timing source api which is used by the step-dir stepper common code.
This allows the reusable common code to configure different timing sources,
since the initial delayable work implementation was inacurate for higher
maximum velocities.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Use the shell_device_filter utils method and leverage the new api classing
to only suggest stepper devices via tab-complete within the shell.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
The LIS2DUXS12 is a smart, digital, 3-axis linear accelerometer whose
MEMS and ASIC have been expressly designed to combine the lowest current
consumption possible with features such as always-on antialiasing
filtering, a finite state machine (FSM) and machine learning core (MLC)
with adaptive self-configuration (ASC), and an analog hub / Qvar sensing
channel.
(https://www.st.com/en/mems-and-sensors/lis2duxs12.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Prepare the driver to be able to handle other DUX software compatible
devices. Currently the driver handles the st_lis2dux12 compatible only.
Do following major changes:
1. Introduce the lis2dux12_chip_api structure filled with device specific
APIs. At the moment define following callback:
- api_lis2dux12_set_odr_raw()
- api_lis2dux12_set_range()
- api_lis2dux12_sample_fetch_accel()
- api_lis2dux12_sample_fetch_temp()
- api_lis2dux12_handle_interrupt()
- api_lis2dux12_init_interrupt()
2. Prepare specific APIs for st_lis2dux12 device.
3. Make DT instantiation on inst + name basis, and not only by inst. This
commit only use "name = DT_DRV_COMPAT = st_lis2dux12".
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Regardless of the argument specified, it always references the
property of the 0th, so it was corrected to reference the instance
specified by the argument.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
For a 16-bit data bus, "DT_INST_PROP_LEN(n, data_gpios)" returns 16
which is equals "MIPI_DBI_MAX_DATA_BUS_WIDTH(16)".
As a result, the assertion will always be triggered.
Use a "<=" condition for the assertion instead.
Signed-off-by: Hua Zheng <writeforever@foxmail.com>
Command "waitms 50" on ChromeBook EC console, then it will crash EC.
Because arch_busy_wait() is re-entried by two different tasks,
the second calling will reset the timer and may cause the first
calling to fail to reach the waiting destination
(if the first calling's wait time is longer enough).
Verified by follow test pattern:
west build -p auto -b it8xxx2_evb tests/kernel/timer/timer_api
west build -p auto -b it8xxx2_evb tests/kernel/timer/timer_error_case
west build -p auto -b it8xxx2_evb tests/kernel/timer/timer_monotonic
west build -p auto -b it8xxx2_evb tests/kernel/timer/starve
west build -p auto -b it8xxx2_evb tests/kernel/context
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Add empty function stubs to support building with the newly introduced
CONFIG_BUILD_ONLY_NO_BLOBS option.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
The address passed in to the function was incorrect causing
failures when porting to RT1180.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
For the lists of properties passed as a pointer to the get_props and
set_props functions, there is no reason to not make the pointer const as
the called functions will not and should not alter the pointed-to data.
In practice, not having the pointers const can cause compilation errors
if trying to pass in a const array of properties.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
Use uint64_t instead of uint32_t for the FLASH_STM32_EX_OP_SECTOR_WP
extended operation.
Some chips have two banks, more than 16 sectors each e.g. stm32h7a3xx
chips, so more than 32 bits are required.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Fixed bug calculating offset of registers after unused space in the ADC
register space for the SZ package parts.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Avoid referring to Pico 2 (the name of a board). In this context,
RPI_PICO is used to refer to the (Zephyr) `SOC_FAMILY` rather than the
Pico 1 board. This clarifies common numerical values between the RP2040
and RP2350 SoC series, and enables existing DTS files to be used with
RP2350-based boards with fewer changes.
Remove the use of Zehpyr's `CONFIG_` macros from the device tree files,
and replace them with `SOC_SERIES`-specific files. Update the driver
implementation to conditionally include the correct file. Update
documentation and samples to match.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
The RP2350 SoC series contain two timer peripherals. Extend the driver
to support using the second timer (`TIMER1`).
N.b. this requires a fix from the Pico SDK to be patched into
hal_rpi_pico. See https://github.com/raspberrypi/pico-sdk/pull/1949 .
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
The watchdog register configuration of RP2350 differs from that
of RP2040, so we make fit that.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
Unlike the RP2040, the RP2350 has multiple tick generators that need to
be started. Start TIMER0 and TIMER1 tick generators during
clock_control_init.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
Extend the existing driver to add some initial support for the new SoC,
whilst maintaining compatibility with the RP2040.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
RP2350 is Raspberry Pi's newest SoC. From the datasheet:
"RP2350 is a new family of microcontrollers from Raspberry Pi that
offers significant enhancements over RP2040. Key features include:
• Dual Cortex-M33 or Hazard3 processors at 150 MHz
• 520 kB on-chip SRAM, in 10 independent banks
• 8 kB of one-time-programmable storage (OTP)
• Up to 16 MB of external QSPI flash/PSRAM via dedicated QSPI bus
...
"
This commit introduces some changes to support the existing RP2040 and
what is describe by Raspberry Pi as the "RP2350 family". Currently there
are 4 published products in the family: RP2350A, RP2350B, RP2354A, and
RP2354A. Within Zephyr's taxonomy, split the configuration as follows:
Family: Raspberry Pi Pico. This contains all RP2XXX SoCs,
SoC Series: RP2040 and RP2350.
SoC: RP2040 and, for now, just the RP2350A, which is present on the Pico
2, where the A suffix indicates QFN-60 package type. This structure is
reflected in `soc/raspberrypi/soc.yml`, and somewhat assumes that there
won't be a RP2050, for example, as a RP2040 with more RAM.
This is foundation work ahead of introducing support for Raspberry Pi's
Pico 2 board, which is fitted with a RP2350A and 4MB of flash.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add support for SoC-specific clock ids and update the initialization
function to support the existing RP2040 and add support for the RP2350.
clock_control_rpi_pico.c uses numerical values for clock ids taken from
rpi_pico_clock.h which are the "clock generator". For the RP2350 these
values are different for some of the same logical clock sources, as well
as the RP2040 and RP2350 having different clock sources available.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
XIP prefetching seems to still be running, even while interrupts are
disabled. Therefore it is important to wait for the FlexSPI to be idle
before performing a write/erase operation.
Signed-off-by: Martin Stumpf <martin.stumpf@vected.de>
Add a GPIO driver for the Microchip MEC5 HAL based chips.
Current devices are: MEC174x, MEC175x, and HAL version of
MEC172x named MECH172x.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This adds initial support for NXP SDMA controller. We make use
of NXP HAL to configure the IP.
SDMA uses BD (buffer descriptors) to describe a transfer. We create
a cyclic list of descriptors and trigger them manually at start and
later when data is available.
This is tested using Sound Open Firmware app on top of Zephyr.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
- rename enable-gpios to en-gpios in adi,tmc2209
- place en-gpios in common stepper-controller.yaml
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
IRQ 1 is reserved for WiFi in ESP-IDF, which is used as the basis
for the Espressif HAL in Zephyr.
If IRQ 1 is used by Zephyr and too many other peripherals (e.g.
multiple UARTs) are enabled, WiFi stops working.
Marking IRQ 1 as "not available" seems to fix the issue.
Fixes#82874
Signed-off-by: Martin Jäger <martin@libre.solar>
The DHT[11/22] sensor driver fails to read data due to an extra
"gpio_pin_set_dt" that is occurs prior to waiting for the sensor active
response. This leads to consistent failed reads on esp32 (devkitc,
wrover). After removing this line reads are consistently successful.
Signed-off-by: Omar Naffaa <omarnaffaa.on@gmail.com>
Fast SPIM instances (SPIM120 and SPIM121) for correct operation require
the highest frequency from the global HSFLL. This commit adds needed
clock controller requests to the driver. When the runtime device power
management is enabled, the frequency is requested as long as the SPIM
is resumed, otherwise it is requested for the duration of transfers.
This commit also adds a missing call to `pm_device_runtime_put()` when
SPIM reconfiguration fails.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is a follow-up to commit fe0e2dbc60.
If `nrf_clock_control_request_sync()` ends up with a timeout, before
returning it must cancel the request that was not fulfilled on time.
Otherwise, the request may actually finish successfully a bit later,
but the caller will not be aware that the clock needs to be released
(since the call resulted in an error). And actually even more serious
problem is that because the `req` structure is placed on stack, after
the function returns, the contents of this structure will be probably
overwritten with some other data, so if the request finishes at that
point, an attempt to execute the callback function pointed by this
structure will most likely cause a crash.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
coverity complains of a missing break statement in SENSOR_CHAN_ALL case
this is fixed by adding __attribute__((fallthrough))
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
The LoRa driver does not allow to pass void* user_data to callback in
lora_recv_async function. This leads to complex way of using the API. This
commit fixes the issue and adds the field to the function and to the
callback.
Signed-off-by: Aleksander Dejewski <aleksander.dejewski@gmail.com>
Rename "nxp,kinetis-ftm-pwm" compatible to "nxp,ftm-pwm" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Propagate bit ordering and type of CS pin to HAL layer. Previously,
the driver assumed MSB first and EUSART hardware CS control.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Add nrf twis (I2C controller supporting I2C peripheral role and
EasyDMA) support, including updating the existing twis dt binding
to match the hardware with proper examples.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
This patch adds support for HOST OpenThread communication to the RCP
co-processor via UART using SPINEL protocol.
The aim is to use OpenThread's RCP (Radio Co-Processor) with HOST device
(for example imxRT1020). Such configuration is the same as one used
with PC program (ot-cli) and RCP.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Implement the SPI context lock in the USART SPI driver for
EFM32/EFR32.
Remove incorrect -EBUSY error when spi_release() is called while
there are still bytes in the TX FIFO. This condition does not
cause the act of releasing the lock to fail.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Start and stop SAP, the IPv4 address is not removed, if then use STA
mode to connect to EXT-AP with same gateway address as the stopped
SAP, STA will not get the DHCP IPv4 address, as the DHCP offer packet
is dropped due to detect of IPv4 address conflict. Removing SAP IPv4
address when stopped SAP can fix this issue.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
apx needs to set compare b due to errata of XTAL glitch
ap4p needs to set minimum delta to 4
err026 requires XTAL to not be switched off/on when resetting
Signed-off-by: Richard Wheatley <richard.wheatley@ambiq.com>
Remove orphaned `k_mutex_unlock` in `eeprom_at25_read` as
the lock/unlock pair is handled in `eeprom_at2x_read` instead.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
To maintain consistency in `init_fn` parameter passing,
remove the address-of operator ('&') when assigning the `init_fn`
function pointer in the `DEVICE_DT_INST_DEFINE` macro.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Set up a named device MMIO memory mapping in the GPIO controller's
parent device, map the virtual memory in the init function of the
parent device.
Once the controller's register space has been successfully mapped,
propagate the mapped virtual address to all child (= GPIO bank)
devices. While it is possible to add a named mapping to every
single GPIO bank device and initialize it in the respective bank
device's init function, this would result in multiple virtual
address mappings all pointing to the same 4k of physical memory.
I assume that, although all those mappings having the same attri-
butes, such a setup is at least discouraged.
Signed-off-by: Immo Birnbaum <mail@birnbaum.immo>
Return standard baudrate on a uart_config_get call instead of
rough calculated numbers.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
Since now Mbed TLS automatically selects ENTROPY_GENERATOR (or the
test generator, depending on the platform) we can remove this dependency
from all BT related tests and samples.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Enable buffered write for nRF54l RRAM flash driver by default.
CONFIG_NRF_RRAM_WRITE_BUFFER_SIZE=1 means that write will be buffered
by 16 B buffer (native RRAM write-bock-size).
This allows optimal life-endurance of RRAM memory.
For reference" DTS declares 16 write-block-size already.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
This patch fixes an assert in net_buf_simple_add() function when the
lan_9250 driver would add previously added data to the net buffer
on receiving large (>128 bytes) packat. This fix was to use the frags
field of the net_buf structure instead.
Tested with a nRF54L15 DK and eth3 click board (with nordic connect sdk
2.8.0 and this patch).
Signed-off-by: Balaji Srinivasan <balaji.srinivasan@autostoresystem.com>
Creation of the new zephyr\soc\nxp\common\nxp_nbu.c driver which manage
the interruption of the NBU. This modification is mandatory to support a
coex application which includes Bluetooth and 802.15.4 on the same
narrow band path.
Signed-off-by: Xavier Razavet <xavier.razavet@nxp.com>
This commit Modifies the DMA STM32 Kconfig to enable shared IRQ
support for the STM32U0 series.
This change ensures DMA channels with shared IRQs are properly
configured for stm32u0 devices.
Signed-off-by: Mohammad Badawi <zephyr@exalt.ps>
Signed-off-by: Sara Touqan <zephyr@exalt.ps>
The clock_stm32_ll_common.c function set_up_plls calls
LL_RCC_PLL_Disable();and it was not waiting for the
disable to complete before trying to configure
the pll sysclock which creates a race condition for
pll configuration.The wait for re-enabling the RCC pll
is already there, it was just missing the wait for
the disable before configuration. Also added the wait for PLL2.
Signed-off-by: Benjamin Curtis Byers <ben.byers@ubcobikes.com>
Adapt the stm32 flash driver for the stm32h7rs serie where some
bit of the FLASH registers are named differently from stm32h7 serie.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch will save configured link clock and ensure
ssp starts with xtal clock if ssp ver >= 2.0
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
First commit to add support for gpio interrupt on Renesas RA
- Add support for external interrupt driver
- Add support for gpio interrupt config
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
create rampstat Kconfig template to enable respective tmc drivers to
reuse the common configurations
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Convert vendor specific **_WIFI_BUILD_ONLY_MODE symbol as global
in order to provide common build flag to enable CI with no blobs.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
ADS131M02 is Texas Instruments 2-channel, 24-Bit differential
input ADC which support wide range datarate.
Driver add support for adc read, channel configure, adc sampling
mode configuration and power management.
[1]. https://www.ti.com/lit/ds/symlink/ads131m02.pdf
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
config->base is already defined as ADC_TypeDef so no there is no need to
cast it as such. Remove all occurrences throughout the file.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Now that clock source and sequencer are defined with strings in device
tree, move the old defines directly in the driver
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Now that st,adc-sequencer and st,adc_clock-source use a string, update the
ADC driver.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
fu drv adc update driver with string
Remove specific cases for H7 and U5: group them together and only call a
single function. ADC3 of H72x/H73x and ADC4 of U5 are different from other
ADC of their series, and have dedicated functions in the LL for enabling
DMA, but they're doing the exact same operation as
LL_ADC_REG_SetDataTransferMode.
Incidentally, this change allows H7A/H7B to use the DMA (it seems to have
been missed before).
Last, this change enables the DMA support for F1x ADC.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
STM32F3 and H7 have multiple ADC versions difficult to differentiate.
Use clearer macros to make code more readable.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Use shell_device_get_binding() instead of device_get_binding() so that
we get the device based on its name and in addition by its label.
Signed-off-by: Yishai Jaffe <yishai1999@gmail.com>
Mode 0 cannot establish a connection when used as a UDP server,
replace mode 0 with mode 2 to save the client's IP and port as
the communication address when a message is received.
Fixes#82898
Signed-off-by: Hongquan Li <hongquan.prog@gmail.com>
