Add wsen_pdus_25131308XXXXX driver with
the corrected name and compatibility with
the hal update as well as added new features..
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Fixes issue introduced in #76460
The previous code attempted to detect whether TMAG5273 or TMAG3001 was
connected based on DEVICE ID register. This doesn't work as the bits that
denote the version on one part are undefined on the other part, and cannot
be relied on to be zero.
This commit adds a TMAG3001 compatible which (for now) is just derived from
the TMAG5273 compatible. This allows TMAG3001 to be specified directly in
the DT. The driver code is updated to support both compatibles.
Signed-off-by: Yiding Jia <yiding.jia@gmail.com>
Add a property holding calibration resolution, similar to what already
exists in the st,stm32-temp-cal-common binding.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
This is a squash of all the groundwork needed to
get a functioning driver for the DS3231 with the RTC API.
Signed-off-by: Gergo Vari <work@gergovari.com>
Add the Sensor Fusion Low Power (SFLP) FIFO streaming capability,
using RTIO. The decode function is now aware of parsing following FIFO
tags:
- LSM6DSV16X_SFLP_GAME_ROTATION_VECTOR_TAG
- LSM6DSV16X_SFLP_GYROSCOPE_BIAS_TAG
- LSM6DSV16X_SFLP_GRAVITY_VECTOR_TAG
To activate SFLP the user should put in DT the proper configuration.
For example, to activate a 60Hz SFLP FIFO batching rate of game rotation
vector, gravity vector and gbias components, the user should add in DT
the following:
sflp-odr = <LSM6DSV16X_DT_SFLP_ODR_AT_60Hz>;
sflp-fifo-enable = <LSM6DSV16X_DT_SFLP_FIFO_GAME_ROTATION_GRAVITY_GBIAS>;
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The LIS2DUXS12 is a smart, digital, 3-axis linear accelerometer whose
MEMS and ASIC have been expressly designed to combine the lowest current
consumption possible with features such as always-on antialiasing
filtering, a finite state machine (FSM) and machine learning core (MLC)
with adaptive self-configuration (ASC), and an analog hub / Qvar sensing
channel.
(https://www.st.com/en/mems-and-sensors/lis2duxs12.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add the power mode, accel and gyro filtering options,
and apex features. Add -p and -s compatible.
Signed-off-by: Aurelie Fontaine <aurelie.fontaine@tdk.com>
The `ti,hdc20xx` is a common definition for TI HDC20xx series,
so the actual device named `hdc20xx` does not exist.
Remove the "compatible" section.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Update discharge current limit property to be aligned
with the most recent npm1300 datasheet.
This affects the discharge current measurement calculation,
which needs to be scaled accordingly.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add sensor driver for npm2100 pmic.
This pmic performs measurements of battery voltage, regulator voltage
and die temperature.
Configurable pmic attributes are also organized under this driver.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add support for setting the sample frequency via `attr_set` and the
output data rate from device tree source.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add RTIO async and RTIO stream functionalities that enables,
among all the other things, the sensor data streaming from FIFO.
RTIO stream is using both SENSOR_TRIG_FIFO_WATERMARK and
SENSOR_TRIG_FIFO_FULL triggers. The decoder currently only supports
following FIFO tags:
- LSM6DSV16X_XL_NC_TAG
- LSM6DSV16X_GY_NC_TAG
- LSM6DSV16X_TEMP_NC_TAG
Following FIFO parameters has to be defined in device tree to
correctly stream sensor data:
- fifo-watermark (defaults to 32)
- accel-fifo-batch-rate (defaults to LSM6DSV16X_DT_XL_NOT_BATCHED)
- gyro-fifo-batch-rate (defaults to LSM6DSV16X_DT_GY_NOT_BATCHED)
- temp-fifo-batch-rate (defaults to LSM6DSV16X_DT_TEMP_NOT_BATCHED)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The ILPS22QS is an ultra-compact piezoresistive absolute pressure sensor
which functions as a digital output barometer, supporting dual full-scale
up to user- selectable 4060 hPa. The device delivers ultra-low pressure
noise with very low power consumption and operates over an extended
temperature range from -40 °C to +105 °C.
(https://www.st.com/en/mems-and-sensors/ilps22qs.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Updated ADXL345 driver with RTIO stream functionality.
Added Trigger intterupt functionality. RTIO stream is using
FIFO threshold.Together with RTIO stream, RTIO async read
is also implemented.
Signed-off-by: Dimitrije Lilic <dimitrije.lilic@orioninc.com>
Add wsen_hids_2525020210002 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Add support for Bosch bmp390 sensor, the drop in replacement for the
bmp388 with same register but different chip-id. This patch make use
of "bosch_bmp390" or "bosch_bmp388" and set the specific chip-id in a
data->chip-id variable, which then used to check against the register
value.
Additional, manual shift operation had been replaced with ENDIAN safe
macros and calibration values with target variable of int16_t add a
cast for it.
bmp388_spi: read register implementation wrong, fixed it.
tx-buffer must be <addr><dummy><dummy> in order to receive the
register value. Read registers in burst mode and have rx and tx
buffer same spi_buf to avoid clock stop and delay with nrf5.
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
The NTC thermistor implementation assumes a constant pull-up voltage
and that the ADC channel is measured against a reference voltage so that
the absolute voltage across the NTC can be calculated. Based on the
relationship of `pullup-uv` and this absolute NTC voltage, the resistance
of the NTC is calculated.
There are applications where the "pullup-uv" is not constant, but VDD.
Most ADCs support relative measurements against VDD. If `pullup-uv` is not
defined, the implementation assumes now that the ADC channel is configured
to use VDD as a reference and therefore no millivolt conversion is
required.
Signed-off-by: Stefan Schwendeler <Stefan.Schwendeler@husqvarnagroup.com>
Current nPM1300 charger driver does not work with batteries
without NTC thermistor. Added supported for this feature.
Signed-off-by: Javier Santos <jasr93@outlook.es>
This commit adds support for INA236 into the existing INA230 driver.
These two chips are similar enough to share most of the code.
The device can be defined the same way as INA230 and we only have
the extra option to select the high-precision mode.
```
ina236: ina236@40 {
status = "okay";
compatible = "ti,ina236", "ti,ina230";
reg = <0x40>;
adc-mode = "Bus and shunt voltage continuous";
vbus-conversion-time-us = <1100>;
vshunt-conversion-time-us = <1100>;
avg-count = <1>;
current-lsb-microamps = <1000>;
rshunt-micro-ohms = <15000>;
alert-gpios = <&gpiod 0 GPIO_ACTIVE_LOW>;
high-precision;
};
```
Signed-off-by: Tomáš Juřena <jurenatomas@gmail.com>
TI tmp1075 driver implemented based on tmp108 driver.
The driver initializes the sensor based on the DTS.
Added tmp1075 example overlay file to thermometer sample.
All you need to do to use the sensor is to connect the I2C and
optionally interrupt line.
To see default DTS configuration option inspect `ti,tmp1075.yaml`
bindings file and sensor spec.
Signed-off-by: Paweł Czaplewski <pawel.czaplewski@arrow.com>
Update the devicetree binding for the nxp,kinetis-acmp comparator and
move the binding to dts/bindings/comparator.
The update to the binding includes:
- Remove unused io-channel-cells property
- Remove unused sensor-device include
- Adding missing properties dac config, discrete mode config, and
input configs.
- Rename properties to exclude redundant vendor prefix since props in
this binding are not inhereted, and as such, don't need to be
namespaced.
- Deprecate the old names of the renamed properties
The sensor based device driver has been updated to support both the
deprecated and new property names. This allows it to use both
nxp,enable-sample and filter-enable-sample for example.
Additionally, remove the unused io-channel-cells properties from
in-tree nodes of compatible = "nxp,kinetis-acmp"
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Change the STM32 Temperature Sensor bindings to accept the average slope
value in string form instead of integer. With this change, it is possible
to use the raw decimal value found in each MCU's datasheet instead of
needing to scale it (differently depending on series!). This also allows
regrouping the property in a single file to reduce duplication.
Also update all DTSI files affected by this change and the dietemp driver
to accept the property's new format.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Improve the STM32 dietemp sensor bindings by rewording the descriptions
of bindings and properties.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Reduce duplication in STM32 dietemp bindings by regrouping the 'ntc'
property declared in both "st,stm32-temp" and "st,stm32c0-temp-cal"
to the shared "st,stm32-temp-common" binding.
"st,stm32-temp-cal" is also modified to block 'ntc' property on include as
no dual-calibration sensors to date require it (this could be changed later
when need arises).
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Set the 'avgslope' property of 'st,stm32c0-temp-cal' to required, and
remove its default value, to ensure new series cannot be introduced without
setting the property to the correct value explicitly.
This change does not require any DTSI modification, because there are only
two files using this compatible (stm32f030.dtsi / stm32c0.dtsi), and both
of these already set 'avgslope' explicitly.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Set the 'avgslope' property of 'st,stm32-temp' to required, and remove its
default value, to ensure new series cannot be introduced without setting
the property to the correct value explicitly.
This change does not require any DTSI modification, because there are only
two files using this compatible (stm32f1.dtsi / stm32f2.dtsi), and both of
these already set 'avgslope' explicitly.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Set the 'v25' property of 'st,stm32-temp' to required, and remove its
default value, to ensure new series cannot be introduced without setting
the property to the correct value explicitly.
This change does not require any DTSI modification, because there are only
two files using this compatible (stm32f1.dtsi / stm32f2.dtsi), and both of
these already set 'v25' explicitly.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add all the necessary files to add apds9253 Avago sensor driver.
Sensor available at https://docs.broadcom.com/doc/APDS-9253-001-DS
Signed-off-by: Margherita Milani <margherita.milani@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Add the yaml files needed for the dts binding of the Bosch bmp180 sensor.
V2 Fixup
--------
yaml fixup for complient checks
merge bmp180-i2c.yaml and bmp180.yaml
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
This transforms the existing driver for the Microchip MCP9808
to be used as a generic driver to be used with all
JEDEC JC 42.4 compliant temperature sensor chips.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
