At the present time, Zephyr does has overlap between sleeping and
suspending. Not only should sleeping and suspended be orthogonal
states, but we should ensure users always employ the correct API.
For example, to wake a sleeping thread, k_wakeup() should be used,
and to resume a suspended thread, k_thread_resume() should be used.
However, at the present time k_thread_resume() can be used on a
thread that called k_sleep(K_FOREVER). Sleeping should have nothing
to do with suspension.
This commit introduces the new _THREAD_SLEEPING thread state along
with some prep-work to facilitate the decoupling of the sleeping and
suspended thread states.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
Added support for SPI in 4-wire and 3-wire configurations to
the Infineon AIROC WiFi driver (drivers/wifi/infineon).
Review changes:
Move DT_DRV_COMPAT to common header file
Correct board-specific preprocessor lines
Removed AIROC_MAP_COUNTRY_CODE
Move Pico W configuration details to devicetree
Use pinctrl to manage shared data/interrupt GPIO
Clean up bus selection in Kconfig.airoc
Make SDIO and SPI bus struct independent
Replace LOG_DBG with LOG_ERR
Remove functionally duplicate operation
Remove spurious Kconfig option
Minor cleanup in CMakeLists.txt
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Traditionally threads have been initialized with a PRESTART flag set,
which gets cleared when the thread runs for the first time via either
its timeout or the k_thread_start() API.
But if you think about it, this is no different, semantically, than
SUSPENDED: the thread is prevented from running until the flag is
cleared.
So unify the two. Start threads in the SUSPENDED state, point
everyone looking at the PRESTART bit to the SUSPENDED flag, and make
k_thread_start() be a synonym for k_thread_resume().
There is some mild code size savings from the eliminated duplication,
but the real win here is that we make space in the thread flags byte,
which had run out.
Signed-off-by: Andy Ross <andyross@google.com>
-Update formatting and contents of index.rst for cy8ckit_062s4
-Update formatting and contents of index.rst for cy8ckit_064s0s2_4343w
-Update formatting and contents of index.rst for cy8cproto_062_4343w
-Update formatting and contents of index.rst for cy8cproto_063_ble
-Update formatting and contents of index.rst for xmc45_relax_kit
-Update formatting and contents of index.rst for xmc47_relax_kit
-Change all instances of "PSoC" to "PSOC" for infineon platforms
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
There are HCI drivers which reference the module-specific Kconfig symbols
which are auto-generated when the modules are present. Provide default
definitions for these symbols in case the modules are missing, so that
compliance checking doesn't stumble over seemingly non-existent Kconfig
options.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Issue:
Kconfig WIFI_AIROC should not depend on infineon SOC family selection
for the connection. See issue#77012 for details.
Fix:
- update modules/hal_infineon/Kconfig to be able enable
USE_INFINEON_ABSTRACTION_RTOS for non Infineon SOC family.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
- Add initial version of CYW920829M2EVK-02 board
- [drivers: clock_control] Make it possible to set up both iho and imo
clocks instead of just one or the other
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Removing dependency on cyhal in airoc wifi driver.
It need to build airoc wifi driver with different than
PSoC 6 Soc like STM32
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
When kernel stack is defined as an array, K_KERNEL_STACK_LEN()
is used to calculate the size for each stack in the array.
However, standalone kernel stack has its size calculated by
Z_KERNEL_STACK_SIZE_ADJUST() instead. Depending on the arch
alignment requirement, they may not be the same... which
could cause some confusions. So align them both to use
K_KERNEL_STACK_LEN().
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Added initial version of Infineon AIROC WIFI driver
Added initial version of binding file for Infineon AIROC WIFI
driver
Rename CONFIG_ABSTRACTION_RTOS_COMPONENT_ZEPHYR to
CONFIG_USE_INFINEON_ABSTRACTION_RTOS
Exclude cy8cproto_062_4343w platform from
drivers.modem.esp_at.build test
Change revision hal_infineon to
69c883d3bd9fac8a18dd8384624b8c472a68d06f
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 SDHC/SDIO driver
Added initial version of binding file for Infineon CAT1 SDHC/SDIO
driver
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
- Added initial version of Infineon CAT1 Flash driver
- Added binding file for infineon,cat1-flash-controller.yaml
- Added overlays for subsys/nvs and drivers/flash_shell
to support cy8cproto_063_ble, cy8cproto_062_4343w boards
- Defined erase-block-size in PSoC6 MPN dtsi.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
- Added Cmakefiles for modules\hal_infineon\btstack-integration\,
where handle generation of Bluetooth include blob from HCD binary.
- Supported following device/modules:
-- CYW43012/MURATA-1LV module
-- CYW4343W/MURATA-1DX module
-- CYW43439/MURATA-1YN module
-- CYW4373/STERLING-LWB5plus module
- Added possibility to use user provided BT Firmware HCD file via
kconfig (path must be defined in
CONFIG_CYW43XX_CUSTOM_FIRMWARE_HCD_BLOB)
- Updated top makefile
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Problem:
pull/43494 is causing the CMake warning
No SOURCES given to Zephyr library: modules_hal_infineon
modules_hal_infineon library was defined even if none of the
below subdirectories is added; so, when not building for
Infineon/Cypress devices, the source list for this library
will be empty.
Fix:
Added 'zephyr_library_named(modules_hal_infineon)' under condition
'if(CONFIG_HAS_XMCLIB OR CONFIG_SOC_FAMILY_PSOC6)'
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
