Convert qspi and hyperflash to variants instead of revisions by popular
demand.
And convert evkb into a revision instead of a different board.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
To avoid compilation on boards that do not have arduino_i2c defined,
we will clarify that it is dependent on it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add test configuration for Awinic AW9523B.
This device is a GPIO Expander, and no boards currently implement it.
Define the connection that connects it via the Arduino header and
define a fixture to enable it.
This has been confirmed with nucleo_h503rb.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Enable this test, and provide overlays, in the nrf5340bsim
Note this test specs 2 GPIO pins to be shorted. This can be done
for the simulation target by calling zephyr.exe with the option
`-gpio_conf_file=shorts_config.txt`
Where that file would contain this one line (for the provided overlay),
for the cpunet:
---- shorts_config.txt
short 1.1 1.2
----
And this for the cpuapp:
---- shorts_config.txt
short 3.1 3.2
----
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test, and provide overlays, in the nrf54l15bsim
Note this test specs 2 GPIO pins to be shorted. This can be done
for the simulation target by calling zephyr.exe with the option
`-gpio_conf_file=shorts_config.txt`
Where that file would contain this one line (for the provided overlay)
---- shorts_config.txt
short 1.1 1.2
----
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
1. add delay read config for platforms that has capacitor with pin
2. add dts pin flags to gpio_pin_config when output.
Signed-off-by: Hake Huang <hake.huang@nxp.com>
update boards that can not use the common pins
mimxrt102x reuse with ethernet
mimxrt106x has external pull up
lpcxpresso55s3x reuse with int
add CONFIG_SKIP_PULL_TEST by default to be more general
user can enable this test in customized case with select pin
ST prefer to using D9 D10 pair to testing.
Signed-off-by: Hake Huang <hake.huang@nxp.com>
using arduino header to simplify test settings.
arduino_header D2 and D3 can be used by default.
alt: 118 platforms are enabled for this test.
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Writing directly to Px_DATA_REG modifies pins which are not
indicated by mask, causing gpio_basic_api test to fail.
Use Px_SET_DATA_REG and Px_RESET_DATA_REG to modify only
pins indicated by mask.
Signed-off-by: Ioannis Damigos <ioannis.damigos.uj@renesas.com>
Move samples config files from 'boards' to 'socs' in order to
remove multiple files with the same configuration and render
available samples for new boards. Only changed sample files
which are not board or hardware specific.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
Add frdm_ke17z_fgpio.overlay to add fgpio configuration, and
add update testcase.yml to add FGPIO driver test for frdm_ke17z
and frdm_ke17z512 platforms.
Updated ke17z512 gpio test pins to avoid conflicts with I2C pin.
Signed-off-by: Anke Xiao <anke.xiao@nxp.com>
`checkpatch.pl` requires that dts sources are indented with tabs,
fix all the spaces that slipped in while checkpatch wasn't watching.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Rename all Silicon Labs dev kits to always use the official kit name
as board target name. Previous kit names used various naming schemes,
including putting part of the SoC name in the board name. With HWMv2,
SoC names (if needed) should go in the SoC board qualifier.
Use HWMv2 revisions for the two variants of SLTB010A.
Split the xG27 Dev Kit from the EFR32BG22 Thunderboard. This attempt
at deduplication is confusing due to the very different kit names
and use of different ICs (BG22 vs BG27), and was not continued with
the xG24 Dev Kit, meaning that it wasn't consistent.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
There are several esp32-based boards that its conf and overlay
files are missing proper renaming to match cpu cluster.
This also removes all _SOC_ name from files.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Adjustments of overlay and conf files to adjust for the MERGE removal.
The revert of MERGE requires specific overlay and conf files for boards
which relied on the MERGE feature.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
