The commit removes flash_area_open usage from tests, where it is not tested
and only used to obtain area.
The commit adds tests for flash_area_device_is_ready.
The commit adds test for flash_area_sectors, which is equivalent
of flash_area_get_sectors but takes flash area object instead of flash
area index.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Tests the ADC clock domain on the stm32g0 serie
Possible ADC clock sources are SYStem clock (default) or PLL_P.
No clock source HSI for the ADC tested here.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds a test that checks that the Subnet Bridge behaves correctly
when one or more of the involved subnets are undergoing the Key Refresh
Procedure.
Signed-off-by: Ludvig Jordet <ludvig.jordet@nordicsemi.no>
This introduces a global variable controlling the number of remote nodes
used in a given test case. This allows removal of the `TEST_TYPE_...`
enums and further tests in the future that can use different remote node
counts.
This also cleans up the test source by extracting common tester
initialization to separate functions, avoiding repetition.
Signed-off-by: Ludvig Jordet <ludvig.jordet@nordicsemi.no>
The test interfaces registered addresses within the same subnet. As now
only the subnet part of the address is verified when choosing source
address or interface, it was not deterministic which interface would be
selected. Therefore, make the two interfaces use two different subnets
so that tests that verified which address/interface was used work
reliably as earlier.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add a test case which validates that if two network interfaces are
equally good wrt net mask for LL IPv4 communication, the default
interface is preferred.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add a test case verifying that a proper source IPv4 address and
interface is selected for a given LL destination address.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The PSA Crypto implementation provided by Mbed TLS generally requires
some amount of heap to function, so enable the arena unconditionally
to make the test compatible with MINIMAL_LIBC configurations where the
arena is disabled by default.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves signal tests into a singular
testsuite at tests/posix/signals app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
These are very similar devices to mt8195, minimal changes needed
beyond boilerplate configuration.
In the process, this reworks the board/soc layout to be HWMv2
compliant, with "adsp" becoming a CPU cluster beneath the SOC. So the
name of the boards to west become e.g. "mt8195/mt8195/adsp" (which can
be shortened to "mt8195//adsp" if desired).
Note that the cpuclk driver is not yet ported, it works only with 8195
(the clocking/power architecture seems similar between the parts, but
the graph of wells and clocks is different and historically these have
been three separate drivers in SOF). The biggest changes are in the
image/loader scripts, which needed some rework for cross-device
portability.
Signed-off-by: Andy Ross <andyross@google.com>
This is a feature of the 8195 DSP only, which is used only vestigially
by SOF to store data that nothing reads. The Linux kernel on the
other side uses a shared driver for all 81xx devices, which does not
expose the feature. It seems to work, but it's not worth maintaining
a driver in tree for legacy hardware that will never use it.
Signed-off-by: Andy Ross <andyross@google.com>
Separate the current driver for the FPGA iCE40 into two different ones.
One implements only the SPI load mode, the other one only the GPIO
bitbang mode.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This commit comments out some test AC cases that are failing in bsim.
These will be investigated in PR #82199.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Introduce `CONFIG_RISCV_GP_PURPOSE` choice to make sure that only
one of `CONFIG_RISCV_GP` or `CONFIG_RISCV_CURRENT_VIA_GP` can be
enabled, instead of relying of dependencies.
To do that, introduce a new
`CONFIG_RISCV_SOC_HAS_GP_RELATIVE_ADDRESSING` that can be selected
by SoC when it implemented global pointer (GP) initialization for
relative addressing in its linker.
`CONFIG_RISCV_GP` will be the default choice when
`CONFIG_RISCV_SOC_HAS_GP_RELATIVE_ADDRESSING=y`
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Reset the the `gp` register to `_kernel->cpus[i].current` when
`CONFIG_USERSPACE` is enabled on exception to keep it sane.
Updated the testcase to test both `CONFIG_RISCV_GP` and
`CONFIG_RISCV_CURRENT_VIA_GP`.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
If nrf52840dk/nrf52840 is an integration platform, it should also be an
allowed platform, otherwise the test run breaks down.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
The commit removes storage.stream_flash.mpu_allow_flash_write as it was
pointless, and moves nrf52840, as integration platform, to
storage.stream_flash.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves spinlock into a singular
testsuite at tests/posix/spinlocks app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
Increase test and main stack sizes for the qemu_cortex_m3 platform
in order to be able to successfully run the test.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This commit fixes
tests/bsim/bluetooth/ll/multiple_id/tests_scripts/multiple.sh.
The reason is that this test seems to depend on random number
sequence in order to have the proper scheduling.
It also fixes some AC tests by commenting out failing test
cases. The reason of the failure is still unknown and needs
to be investigated in future work.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Moving from TinyCrypt to PSA Crypto API caused an entropy source
to be always required, so this commit adds it in tests where
necessary.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Increase the number of key slots in the PSA Crypto core
for some tests using more keys than the default (16).
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Include Mbed TLS headers to the build system. This is required
because these tests do not follow the "standard build pattern"
of Mbed TLS in Zephyr, otherwise include files would be already
available after the library has been linked. In these examples
some BT source files and Kconfigs are manually added to the
CmakeLists.txt file bypassing the standard library build pattern,
so Mbed TLS headers must also be added manually.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Since the TinyCrypt library is being deprecated in Zephyr, this
commit set TinyCrypt usage in BT mesh as deprecated and it sets
Mbed TLS PSA Crypto API as the default option (when TF-M is not
available).
Tests are also updated in this commit.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This commit sets PSA Crypto API as the default library to perform
ECC-DH in HCI, replacing TinyCrypt (which is being deprecated).
Therefore the symbol BT_TINYCRYPT_ECC is renamed as BT_SEND_ECC_EMULATION.
References in samples/tests are also fixed.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
CONFIG_BT_USE_PSA_API was used in BT crypto/host modules to select
PSA crypto API over TinyCrypt (which was the default until now).
Since TinyCrypt is being deprecated and PSA crypto API is the new
standard library for crypto operations, CONFIG_BT_USE_PSA_API is
no more needed.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Disabled data caching for nRF54H20dk in wdt_basic_api test.
It caused variables stored in noinit section to be cached,
resulting in reset loop.
Signed-off-by: Michał Stasiak <michal.stasiak@nordicsemi.no>
Add minimum flash requirement to the tests. This will effectively
exclude nrf5340dk/nrf5340/cpuapp/ns as it does not have
enough flash for the application.
Fixes#81862
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Traditionally threads have been initialized with a PRESTART flag set,
which gets cleared when the thread runs for the first time via either
its timeout or the k_thread_start() API.
But if you think about it, this is no different, semantically, than
SUSPENDED: the thread is prevented from running until the flag is
cleared.
So unify the two. Start threads in the SUSPENDED state, point
everyone looking at the PRESTART bit to the SUSPENDED flag, and make
k_thread_start() be a synonym for k_thread_resume().
There is some mild code size savings from the eliminated duplication,
but the real win here is that we make space in the thread flags byte,
which had run out.
Signed-off-by: Andy Ross <andyross@google.com>
The commit removes flash_area_open usage from tests, where it is not tested
and only used to obtain area.
The commit adds tests for flash_area_device_is_ready.
The commit adds test for flash_area_sectors, which is equivalent
of flash_area_get_sectors but takes flash area object instead of flash
area index.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Because the number of ACL RX buffers must be at least the number of
maximum connections plus one, increasing `CONFIG_BT_MAX_CONN` could
inadvertently lead to a build failure if the number of ACL RX buffers is
not also increased. This dependency may not be obvious to users.
To address this issue, this commit deprecates the
`CONFIG_BT_BUF_RX_COUNT` Kconfig symbol and computes the value in
`buf.h` using the new `BT_BUF_RX_COUNT` define. Note that the default
value and the minimum range value have been changed to 0 to "disable"
the option.
Additionally, to allow users to increase the number of ACL RX buffers,
this commit introduces the new `CONFIG_BT_BUF_RX_COUNT_EXTRA` Kconfig
symbol. The value of this symbol will be added to the computed value of
`BT_BUF_RX_COUNT`.
The configurations of tests and samples have been updated to reflect
these changes.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
This commit refactos set_actual_position to set_reference_position.
stepper_set_reference_position is more apt in regards to what this func
actually does
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
The #81456 fixed the driver issue related to issue #81454. This add
the RTC configurations on sam_v71_xult board to enable test coverage.
Fixes#81454
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
nrf5340_hci_ipc.conf and nrf5340_hci_ipc_cpunet.conf were board specific
rename them for generic multi-core board support
Signed-off-by: Aytürk Düzen <ayturk.duzen@nordicsemi.no>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves fnmatch, getopt and getentropy
into a singular testsuite at tests/posix/c_lib_ext app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
Without this PTS tests do not pass. These values are copied from a
commit aimed at unifying the prj.conf files in this directory. I do not
know which of these are strictly necessary to make the tests pass.
Copying them all poses no harm since the unification will be done later
anyway.
Co-authored-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
This API gives better control on L2CAP COC credits and suits better
for Upper Tester implementation.
Co-authored-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Enable some high reliability CAP tests by increasing ISO Tx
buffer counts in the Controller to sufficiently generate
number of complete when multiple SDUs are transmitted in
single ISO interval with use of pre-transmissions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This build would fail in CI for reasons that are not obvious.
```
west twister -i -p qemu_arc/qemu_arc_em \
-s tests/posix/common/portability.posix.common.userspace
scripts/build/gen_kobject_placeholders.py did not reserve \
enough space for kobject rodata.
```
It's the only platform that fails this way.
Exclude it from this test temporarily until #82059 is fixed.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Add devicetree node for code RAM, code RAM can be accessed
over AIXM bus or AXIF bus. Code access via AXIF interface
provides the best optimal performance
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
The ASCS unit tests had various errors after adding support for
dynamic registration.
Several tests did not properly clean up after failure, causing other
tests to fail when they shouldn't.
Moved the register tests to their own file as they should not
do the register in the "before" function.
The test_ascs_unregister_with_ases_in_config_state test was also
removed, as it had both issues and the state that it wants to test
cannot be reached with the current API - It is not possible to
put an ASE in the configured state without callbacks,
and registered callbacks prevents us from calling
bt_bap_unicast_server_unregister to trigger the case as that can
only be done if callbacks are unregistered. Since unregistering
callbacks also puts all ASEs to the idle state, it is not possible
to call bt_bap_unicast_server_unregister for a non-idle ASE.
The testcase.yaml was also missing some Kconfig options to
properly enable the client tests.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add collector parameter to metric creation macros so that it
is possible to bind the metric to collector already at built
time.
Also add optional user_data to metric macro calls so that user
can add optional data there. This will be used by network statistics
Prometheus support in subsequent commits.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Embed "struct prometheus_metric" to individual metric like
counter, gauge, histogram and summary. This way we avoid having
a separate base pointer in specific metrict struct. We also do
not need to search the specific metric from base metric as
we can simply use CONTAINER_OF() macro to get the base metric.
This embedding means that the counter, gauge, histogram and summary
metric define macros are changed as user does not need to create a
separate "struct prometheus_metric".
Convert the tests and sample to use the new macros.
Remove also the static from metric creation macros so that user
can decide whether it needs collector to be static or not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Benchmarks are not tests, we run them to verify they still work and do
not bitrot. Running them on each architecture should be sufficient.
This reduces amount of churn in CI and still allows them to be run
individually on platforms.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Don't duplicate the test's output running it on `native_sim` after
`LOG_BACKEND_NATIVE_POSIX` was enabled by default (bd9836be8c)
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Don't duplicate the test's output running it on `native_sim` after
`LOG_BACKEND_NATIVE_POSIX` was enabled by default (bd9836be8c)
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Some code that automatically gets embedded on some platforms relies
on having `CONFIG_TIMEOUT_64BIT` enabled.
Do not force disabling that Kconfig option in the test configuration,
as that will make the test fail to compile on those platforms.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves syslog into a singular
testsuite at tests/posix/xsi_system_logging app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
Adding new CONFIG_MBEDTLS_PSA_KEY_SLOT_COUNT to select the number
of key slots in PSA Crypto core. The default value is 16. Be aware
that key slots consume RAM memory even if unused, so the proper value
should be a compromise between the number of slots required by
the application and the available RAM in the system.
This commit also:
- updates tests/crypto/secp256r1/mbedtls.conf to showcase how to
use this new symbol to reduce RAM footprint.
- tests/bsim/bluetooth/mesh/overlay_psa.conf to support all the
keys used in the test.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Adding the Kconfig symbol CONFIG_MBEDTLS_PSA_STATIC_KEY_SLOTS
to allow Mbed TLS's PSA Crypto core to use static key buffers
to store key's material. This helps reducing heap memory
usage and, potentially, it also discard code implementing
heap memory management if there's no other module in the build
that makes use of it.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Reducing the heap requirement for the hci_ipc sample from
8KiB to 4KiB. It has been tested in various configurations to
work with 2300, but 4KiB was used to provide some leeway for
future updates.
The heap requirement is not documented, and it is unclear why
values lower than 2300 (not exact number) won't boot, and should
be investigated further.
Memory has become a very scarce resource for especially the ISO
builds for the nRF5340, which is why this is getting reduced.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The SSP driver has odd dependency to outside definition of
CONFIG_INTEL_NM. This is in practise tied to SSP hardware
version and always enabled for SSP block version 1.0.
Use the new SSP_IP_VER define to replace the CONFIG_INTEL_MN
preprocssor checks. Also modify the board test case to
remove the obsolete config setting.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Use Kconfig to configure watchdog instead of using expensive filters.
Also disable CONFIG_TEST_HW_STACK_PROTECTION for this test so we do not
have to create special cases.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This fixes memory corruption of delayable work when
tests executes unsupported function.
When test (e.g. only_rx_in_chunks) is executed it starts
delayed work for master functionality (with 10 ms delay).
Later when slave function is tried and reports that
function is unsupported, test is terminated (task ends)
but work is still scheduled.
When next test starts it clears work that is already
scheduled:
static void before(void *not_used)
{
ARG_UNUSED(not_used);
memset(&tdata, 0, sizeof(tdata));
this leads to memory corruption and system work queue
tries to remove work but it never does since head/next
pointers are zeroed at that time.
This just adds after function that cancels work
regardless if it was scheduled or not.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This is a follow-up to 21475774fc,
extending the number of tests and samples that use the new L05 and L10.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds test to assert that thread specific data is deallocated
on thread termination.
Signed-off-by: Jakub Michalski <jmichalski@antmicro.com>
`_current` is now functionally equals to `arch_curr_thread()`, remove
its usage in-tree and deprecate it instead of removing it outright,
as it has been with us since forever.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
As the test uses reentrant time functions like asctime_r or ctime_r,
it should select POSIX_C_LANG_SUPPORT_R. Otherwise there are build
failures observed with the default test configuration if these
functions are not provided by the toolchain.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
Use a string for the mipi-mode property over an integer value, as this
significantly improves the readability of the MIPI DBI device binding.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
flash_copy() is performed on a page.size span but following flash_read()
verification step is performed on EXPECTED_SIZE length (512).
This doesn't work on devices where page.size is lower than EXPECTED_SIZE,
such as STM32L1 where page size is 256.
To fix this, perform verification on the smalest value between page.size
and EXPECTED_SIZE.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Fix some test simulation length be greater than wait time.
These tests completed within 12 seconds, 15 second wait
time is a good value with included margin and a 20 second
simulation time.
These tests failed on this PR CI.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This addresses the following warning building with `CONFIG_64BIT=y`:
error: field precision specifier '.*' expects argument of type 'int',
but argument X has type 'size_t' {aka 'long unsigned int'}
Signed-off-by: Chen Xingyu <hi@xingrz.me>
What looks to be a copy-paste typo was not caught in
code review.
Change .rwlocks to nothing and move the filter to the
common area.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
To increase coverage.
Note that we call twister separatedly for this target, due to the 54l15
overlays using UARTE20 which is indexed in simulation as "2", but as
the nrf52833 does not have 3 instances. So "-uart2_loopback" is not
a valid option for a 52833 executable.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test in the simulated nrf5340 and provide
an appropriate overlay.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test in the simulated nrf54l15 and provide
an appropriate overlay.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test in the simulated nrf54l15 by providing
an appropriate overlay.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add minimum flash requirement to the tests. This will effectively
exclude nrf5340dk/nrf5340/cpuapp/ns as it does not have
enough flash for the application.
Fixes#81608
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Optimize filters and remove build_on_all, this option is already used in
the synchronization sample which has more coverage on small platforms.
Since we only build, it does provide basic sanitcheck for the kernel as
well.
This reduces testplan on PRs and push events by almost 1000 entries that
would only be built or filtered at runtime.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add second instance to be tested on nrf54h20dk. uart120 is a fast UARTE
which works on fixed pin locations. It is not available for cpuppr core.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Replace NULL checks for the set and clear registers with BUILD_ASSERTs
in the iCE40 device instantiation.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Change in default flash map generation, where partitions hanging of
disabled devices will not have flash area generated.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This commit changes the BSIM tests to use the same recv callback
for all tests. The purpose of this is to reduce code duplication
and make it easier to maintain the tests.
This also changes the recv_cb so that in case of any error we log
the most recently received SDU, which should provide more
information about why a test failed in case of RX error.
PBP had to be updated a bit to support the audio_stream
struct.
Also modifies a check and log in bap_stream that was less than
helpful to determine if it was the stream or the endpoint that
was NULL.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Refactor tests to be a bit shorter, so its easier to read
and copy-paste for a new testcase
All idioms like "ret = somecall(); zasser.." are replaced with just
"zassert_ok(some_call());"
Commonly used structures are global and initialized once.
To avoid cross-test side-effects, suite_after-function is added
to cleanup all requests.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Use real-time scheduler with 100x speedup, so timeouts are
accurate enough, but still fast for tests to run.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Updates and aligns the project config file to enable usage of multiple
keys so that users are not required to manually update the project
config file for testing most common mesh scenarios requiring multiple
netkeys and appkeys.
Signed-off-by: Omkar Kulkarni <omkar.kulkarni@nordicsemi.no>
The nRF54L05 and nRF54L10 are identical to the nRF54L15 except for their
memory sizes. Add support for emulating those ICs on the nRF54L15DK.
This commit only adds support for the main application core. Support for
the FLPR core may be added later.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
These two new ICs are variants of the nRF54L15 with different memory
sizes:
- nRF54L05: 500KB RRAM, 96KB RAM
- nRF54L10: 1022KB RRAM, 192KB RAM
- nRF54L15: 1524KB RRAM, 256KB RAM
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Adds two new tests for the Subnet Bridge feature, testing group and
virtual addresses as destinations. The tests are based on the existing
`brg_simple.sh` test, with the addition of a new node and a new subnet
to make sure that messages are bridged to multiple subnets, but only
subnets that have a corresponding entry in the bridging table.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Renames `bt_mesh_test_send_ra` to `bt_mesh_test_send_data` and changes
the corresponding callback funciton as it is used outside of the replay
attack tests, and can be used to send custom data. The function is
extended to accept a UUID parameter to allow sending data to virtual
addresses.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Change the select of BT_PER_ADV_SYNC and BT_EXT_ADV to
depends on. This is an effort to reduce the use of
select for Kconfig options.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Modify ASCS and BAP Broadcast sink to depend on the PAC options
instead of selecting them.
Since Kconfig does not support "depends on X if Y",
a select for PAC_{SRC,SNK} is used depending on
ASCS_ASE_{SRC,SNK}.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The BAP Kconfigs option now depends on
BT_ISO_BROADCASTER instead of selecting it.
This is an effort to reduce the use of select in LE Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The BAP_BROADCAST_SOURCE Kconfig option now depends on
BT_ISO_BROADCASTER instead of selecting it.
This is an effort to reduce the use of select in LE Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Modify the Kconfig options to depend on the GATT
features rather than selecting them.
This is part of an effort to reduce the amount of
selects we use in LE Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This set of changes enables the RS485 hardware connected to usart3 and
provides some overlays that allow for easily running the modbus
rtu_client and rtu_server samples on Opta.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
As long as MBEDTLS_ENTROPY_C is enabled, Mbed TLS needs to
poll some entropy source to gather data that will then be
processed by CTR/HMAC-DRBG modules. This means that in most
of the cases, once MBEDTLS_ENTROPY_C is enabled then also
MBEDTLS_ENTROPY_POLL_ZEPHYR needs to be enabled. This was
done manually until now, as the long list of samples/tests
demonstrate.
This commit solves this dependency by defaulting
MBEDTLS_ENTROPY_POLL_ZEPHYR to on as soon as
MBEDTLS_ENTROPY_C is set. As a consequence, all manual
enablement of MBEDTLS_ENTROPY_POLL_ZEPHYR in samples/tests
are removed.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
The main problem of MBEDTLS_PSA_CRYPTO_LEGACY_RNG is that it
brings in some legacy modules (entropy + ctr_drbg/hmac_drbg)
which means extra ROM/RAM footprint.
MBEDTLS_PSA_CRYPTO_EXTERNAL_RNG instead simply calls to the
CSPRNG which makes it definitely smaller.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves stropts into a singular
testsuite at tests/posix/xsi_streams app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
The filter here should be used to filter for capability:
whether the platform configuration supports userspace. And if
it does support userspace, we then enable CONFIG_TEST_USERSPACE
(and thus CONFIG_USERSPACE) for testing. We should not be
filtering for whether userspace is enabled, but should really
be filtering for whether userspace is supported.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The filter here should be used to filter for capability:
whether the platform configuration supports userspace. And if
it does support userspace, we then enable CONFIG_TEST_USERSPACE
(and thus CONFIG_USERSPACE) for testing. We should not be
filtering for whether userspace is enabled, but should really
be filtering for whether userspace is supported.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add `hifive_unmatched//s7` (earlier selected by default, using
`hifive_unmatched`) and `hifive_unmatched//u74` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Add `hifive_unleashed//e51` (earlier selected by default, using
`hifive_unleashed`) and `hifive_unleashed//u54` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
According to the RISC-V Instruction Set Manual: Volume II, Version 20240411
(Section 3.1.6.6), some implementations may choose to track the dirtiness
of the floating-point register state imprecisely by reporting the state to
be dirty even when it has not been modified. This option reflects that.
Also add a filter in `tests/arch/riscv/fpu_sharing/` based on imprecise
FPU state tracking
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This revert the idea of 3fa7d78 from #78845.
The 3rd level IRQ APIs won't compile when
CONFIG_3RD_LEVEL_INTERRUPT_BITS=0.
Updated testcase accordingly.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Some nodelabels in the display build_all test overlay lacked a "test"
prefix, causing test failures on boards that also define displays with
this nodelabel. Prefix these nodes with "test" to resolve this issue.
Fixes#81610
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Changed interrupt priority for GPIO, default 6 is not suitable for
for the ZERO_LATENCY_IRQS function used in this test.
used in this test.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
The tests were using the default of 1 which is very low,
especially when we might have multiple RX streams.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
There is more native targets than native_sim and native_posix.
Let's exclude them all by architecture.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This commit fixes incorrect c prototype and defintion of
stepper_set_callback to stepper_set_event_callback
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Ports the Thread-Metric suite of benchmarks from ThreadX to Zephyr.
This makes it easier for others to run these benchmarks with the
best set of configuration options for their board so that
they can better compare Zephyr performance to another RTOS.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
Added a flag parameter so that it is possible
to use the bt_cap_initiator_unicast_audio_stop to perform
disable+stop without releasing the streams by setting the
RELEASE flag.
This allows us to use the bt_cap_initiator_unicast_audio_stop
function to just disable streams without releasing them,
as that is requested by some PTS tests such as
CAP/INI/UST/BV-40-C.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Amend the filtering so that the normal mem_map (with exec) test
is not going to run on Intel Audio DSP SoCs.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
With the rename of intel_adsp/ace30_ptl to intel_adsp/ace30/ptl,
the "sim" variant no longer inherit the base configuration. So
make a copy of the .conf file to explicitly target the sim
variant.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Increase the conn interval from 30 to 60 for more stability
in test with multiple lower testers (up to 3).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Shorten the timeouts so that the tests are run in 6 second instead
of 15 seconds.
Use only native_sim for the tests so that the tests are run without
any extra delays.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Previously, twister would fail due to a warning being escalated to
an error because CONFIG_NET_TEST was set.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Test was marked build only with filters in each scenario looking for
sdl-dc which is only available on native_sim, so cut the chase and use
platform_only to narrow things down to native_sim directly instead of
building the world to get information we already know.
reduces build/run time from 78s to 17s on invocation of twister with
default options, saves a ton more when running twister with --all.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The default policy currently directly references the private
variable next_event from policy_events.c to then convert the cycle
of said event (if exists) to a kernel tick in the future, something
policy_events.c already implements and exposes through
pm_policy_next_event_ticks().
Additionally, the implementation of pm_policy_next_state() in
policy_default.c already gets the nearest kernel tick, wherein
the next event has already been accounted for in, see
implementation of pm_system_suspend().
This commit removes the redundant and layer violating computation
if the tick of the next event from policy_default.c and updates
the test test_pm_policy_events to not use default policy to
determine if pm_policy_next_event_ticks() is correct.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
The short sleep (10ms) was not enough any more. Increase the sleep
to 100ms so that system stabilizes between checks.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add tests that verify that stable IIDs generate a proper IPv6
interface identifier described in RFC 7217.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The alloc_buf callback is not used when `seg_recv` is set, so it is
never called in this test. Remove it.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Due to addition of busy threads running on other cores, and
the simulator runs in single thread bouncing through all cores,
we are wasting quite a bit of time just busy waiting. This makes
each simulator run too long for CI. So limit CPU number to 1.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Now that section header cache is persistent, it can be used for
finding sections. Add a new function, similar to llext_find_section()
to use it and deprecate llext_find_section().
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
bt_conn_le_create logs an error if the provided conn is
not NULL. This small change cleans up the log a bit to
avoid the warning.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Everything else is defined as hex, so it makes sense to
be consistent. This will also make it easier to find the
service IDs in the logs that primarily already log
commands and events as hex.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Since the values are defined as hex, e.g. 0x82, it is easier
to compare with the log if they also log them as such.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Obviously, everyone knows that there are 8 bits per byte, so
there isn't a lot of magic happening, per se, but it's also
helpful to clearly denote where the magic number 8 is referring
to the number of bits in a byte.
Occasionally, 8 will refer to a field size or offset in a
structure, MMR, or word. Occasionally, the number 8 will refer
to the number of bytes in a 64-bit value (which should probably
be replaced with `sizeof(uint64_t)`).
For converting bits to bytes, or vice-versa, let's use
`BITS_PER_BYTE` for clarity (or other appropriate `BITS_PER_*`
macros).
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
To ensure payloads are delivered in time for the first subevent
in framed BIS, ISOAL now enforces a (configurable) margin of
the calculated time offset
Without this margin, it has been observed that a broadcaster
can end up consistently missing the first subevent in every third
event in a 7.5 ms ISO with a 10 ms SDU interval
The margin is a conservative 2 ms by default, but can likely be
set a lot lower for most implementations and HWs
Signed-off-by: Troels Nilsson <trnn@demant.com>
Adds compiler flag(s) and some architecture-specific relocations
for ARC. No userspace support, doesn't support all relocations.
Signed-off-by: Lauren Murphy <lauren.murphy@intel.com>
Fixes: #78010
This commit adds tests for the "Gateway Advertisement and Discovery"
process. This includes tests for handling SEARCHGW, GWINFO, and ADVERTISE
as well as manually adding a Gateway for use. Gateway pruning when
missing ADVERTISE messages is also tested.
Signed-off-by: Kenneth Witham <kennywitham4@gmail.com>
Add a driver for the MB85RSM1T FRAM chip.
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Filters already only allow arm and native, so exclude everything else
very early and reduce churn and build time.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Filters already only allow arm and native, so exclude everything else
very early and reduce churn and build time.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Replace the enum for load modes for the iCE40 with a boolean flag,
as there are only two options:
- SPI: default, which should be used whenever possible
- GPIO bitbang: workarorund, in case a low-end microcontroller is used
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Added empty fp register structs for ARM combinations not handled,
i.e. any ARM without a fpu.
Signed-off-by: Lars-Ove Karlsson <lars-ove.karlsson@iar.com>
Log the address and the err/reason values in the connected
and disconnect callbacks.
Since these values are not part of the BTP events it is
difficult to follow the order and reason why disconnects
happen when debugging.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Increase the EXECUTION_TIMEOUT (real time timeout at which the test
will be killed), so we have more margin for CI.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Increase the EXECUTION_TIMEOUT (real time timeout at which the test
will be killed), so we have more margin for CI.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Increase the EXECUTION_TIMEOUT (real time timeout at which the test
will be killed), so we have more margin for CI.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves rwlocks into a singular
testsuite at tests/posix/rwlocks app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves semaphore into a singular
testsuite at tests/posix/semaphores app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves confstr, sysconf and uname into
a singular testsuite at tests/posix/single_process app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
Due to addition of busy threads running on other cores, and
the simulator runs in single thread bouncing through all cores,
we are wasting quite a bit of time just busy waiting. This makes
each simulator run too long for CI. So limit CPU number to 1.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
The sched benchmark is designed for systems with a single
CPU. Otherwise, the timestamps would be wrong when the partner
thread is scheduled on another CPU, i.e. negative values:
```
unpend 63 ready 62 switch -16562 pend 18937 tot 2500 (avg 928)
```
When the system allows for multiple CPUs, spawn a non-preemptible
thread to keep the other CPUs busy.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Adjust default number of test samples which is based on SRAM size.
Test is using 8*TIMER_TEST_SAMPLES and with previous defaults for
the device with 64k RAM it was using 56k of test data leaving only
8k RAM and that was easily not enough. Adjust conditions to
take less samples when SRAM_SIZE is equal to the threshold.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add conversion macros from milliseconds to various units.
The purpose of these macros is to make it more clear/easier
for users to set and read values using milliseconds rather
than the various BT units which may be in 0.625, 1.25 or 10ms
units.
This is especially useful when comparing related values using
different units, such as advertising interval (0.625ms units)
and periodic advertising interval units (1.25ms units).
Users will have to be aware that these macros can provide slightly
different values than what is provided, if the provided values
do not match the units.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Enable this test in the simulated nrf5340 and provide
an appropriate overlay.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test in the simulated nrf5340 and provide
an appropriate overlay.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test in the simulated nrf5340 by providing
an appropriate overlay.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test by providing an overlay for the nrf5340bsim
Both for the app and net core.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test, and provide overlays, in the nrf5340bsim
Note this test specs 2 GPIO pins to be shorted. This can be done
for the simulation target by calling zephyr.exe with the option
`-gpio_conf_file=shorts_config.txt`
Where that file would contain this one line (for the provided overlay),
for the cpunet:
---- shorts_config.txt
short 1.1 1.2
----
And this for the cpuapp:
---- shorts_config.txt
short 3.1 3.2
----
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test, and provide overlays, for the nrf5340bsim.
Both for the app and net core.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable this test, and provide overlays, in the nrf54l15bsim
Note this test specs 2 GPIO pins to be shorted. This can be done
for the simulation target by calling zephyr.exe with the option
`-gpio_conf_file=shorts_config.txt`
Where that file would contain this one line (for the provided overlay)
---- shorts_config.txt
short 1.1 1.2
----
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add support for realloc (and realloc_aligned) into the multi heap lib,
where the buffer sent in will either be reused (maybe shrinked),
or enlarged by allocating on any of the matching heaps of the multi heap.
Signed-off-by: Meir Komet <mskomet1@gmail.com>
If trying to parse a string like 192.0.2.2:80/foobar and
setting the length to 12 which means to parse the IP address
and port, the parsing failed because it used one extra character
from the string. This issue was not present if the input string
was terminated after the port number.
Add a test case to catch this problem.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The commit moves SHA calculation to separate test scenario, so that
it can be run separately from other flash map tests.
This reduces flash wear by not running basic flash map tests each
time different SHA backend is tested.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Remove needless writes/read and erase in flash_area_get_sectors test
scenario, by replacing it with comparison with layout directly obtained
from device.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Use zexpect instead of zassert so that the failed tests do not
stop the test execution but we run all the tests.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The IPV6_JOIN/LEAVE_GROUP corresponds to IPV6_ADD/DROP_MEMBERSHIP
definitions so define the former and add tests for them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The in6addr_any is a global symbol that can be used when any
address (all zero bits) is being referenced.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Validate that the SBS fuel gauge driver returns the expected values for
negative currents (discharging).
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add a new API to cancel just one, or mathing requests,
instead of cancelling all ongoing requests.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
CoAP client should be able to push data through functioning socket
while another sockets is failing or reporting poll() errors.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Add testcase where sending Ack to incomming Confirmable message fails.
This should be reported to application as now the server is unaware
that transmission have succeeded, so we cannot thread it as success.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
* Use sys_rand_get() and seed the CoAP library, so our MIDs are
random.
* Set socket events per socket, so we don't accidentally receive
on wrong socket
* Reply with correct tokens
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves barrier into a singular
testsuite at tests/posix/barriers app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
Fix compilation error by specifying usart1 to be used for uart-pipe.
Add a board-specific configuration file to disable the console,
so, the usart1 will be used only for bluetooth and to specify
the BT_HCI_TX_STACK_SIZE.
Signed-off-by: Nidhal BEN OTHMEN <nidhal.benothmen@st.com>
Add a test to make sure that the `gp` global pointer register used for
relative addressing when `CONFIG_RISCV_GP` is enabled can't be
corrupted by a rogue user thread.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Renamed the label of 'ti_tmp116_eeprom@0' node because 'eeprom' label name
already exists in some boards, such as adp_xc7k/ae350, bytesensi_l,
same54_xpro.
Signed-off-by: Jimmy Zheng <jimmyzhe@andestech.com>
ISH SoCs have zero-address memory mapped to I2C0 controller.
Coredump cannot be triggered by zero-address access.
Signed-off-by: Dong Wang <dong.d.wang@intel.com>
Corrects an issue that was introduced when the interrupt
locking/unlocking was added to the 'sched' benchmark by
unlocking the interrupts before the context switch done by
k_yield(), but after the call to z_unpend_first_thread().
Fixes PR #81050
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
Fixes overlay configuration to allow running the test on CI without
externally connecting two pins.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
Fix 'drivers.ipc.mailbox' test suite to restore and improve
its testing functionality:
* fix printf() redirection through IPM console.
* fix and check the dummy driver initialization.
* specify correct Twister harness type (Console)
and use matching patterns to recognize the expected
console output.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Workaround failing autopts weekly run due to tester
application having Bus Fault in the nRF53 NET core hci_ipc
firmware at startup.
Having atleast 32 bytes free in nRF53x hci_ipc sample to
avoid Bus Fault when Zephyr Kernel does SYSINIT calls.
Reduce supported ISO Broadcaster instance and ISO TX buffer
counts in the Controller hci_ipc firmware.
Add sysbuild support for tester application so that the
build is CI verified.
sysbuild commandline for LE audio PTS testing:
# west build --sysbuild -b nrf5340_audio_dk/nrf5340/cpuapp
-d build/tester tests/bluetooth/tester
-DEXTRA_CONF_FILE="overlay-le-audio.conf"
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Updating the minimum Ram Size for failing tests
that require more ram memory for heap allocations.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Adds the object core configuration to the latency_measure benchmark's
testcase.yaml file as there have been requests for it.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
In ARM architectures the entry_cpu_exception_extend calls
svc #0 when trying to generate a `K_ERR_CPU_EXCEPTION`, however
z_arm_svc calls z_do_oops with a stack frame only, and gets the
reason from `r0`. This means that the test working was just lucky
and running it with another compiler (or setting the value of r0
before the svc #0 call, made the test fail).
Cortex-A/R 32-bit architectures was doing a BKPT, this works better
but will not be a hard exception when debugger is attached.
I switched all the Cortex 32-bits to the ARM specified undefined
instruction.
Also RISC-V has a designated unimp instruction that should be used to
guarantee trap.
Signed-off-by: Robin Kastberg <robin.kastberg@iar.com>
For some weird reasons, enabling ICOUNT would result in some
tests crashing QEMU. So disable ICOUNT.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The test had a few off-by-ones in the code, which caused access
to invalid data.
Fixed by setting the right buffer sizes and the right AD length
fields.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
GAP PAST (and BAP) tests were also enabled since controller support is
under review.
This also adds bqw file which is exported draft project from
Qualification Workspace.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
The test was not being run on arm64 and riscv because the filter was
incorrect. Properly fix the filter to run the test on all platforms
that have any kind of MMU enabled.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Most of the tests in the LLEXT subsystem test suite run with memory
protection hardware (MPU/MMU) disabled, to avoid including memory domain
issues while testing the core functionality. Only a few tests need to
run with MPU/MMU enabled.
This patch simplifies the testcase.yaml by setting the memory protection
as disabled in a shared config file that is included by most tests.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Restore Apollo boards now that the issue has been fixed.
Also remove extra CONFIG_SOC_SERIES_S32ZE filters, as they are already
covered by the 'platform_exclude' common section.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
The fs_loader test is always executed in the main test source when
CONFIG_FILE_SYSTEM is set, and this is in turn enabled by per-board
config overlays. So there is no point in having a separate test case:
it is simply a duplicate of the "readonly" test.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Fix a problem with the test that manifested itself with a surprising
assertion failure at lib/utils/onoff.c:283. Apparently, due to the
stack being too small, some memory got accidentally overwritten.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
If a string is already present in the provided buffer,
prometheus_format_exposition() appends it instead of overwriting,
hence the buffer needs to be cleared on the test start, otherwise it
works by chance.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Fixes the zbus publishing statistics test to account for a non-zero boot
delay, which is often used in hardware testing environments. This fixes
an assertion failure observed on multiple max32 boards in the adi board
farm.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
These tests have been seen failing in CI due to the
real time execution timeout. Let's increase it so it does
not happen.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Remove CONFIG_MMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the mmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
mmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_SDMMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the sdmmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
sdmmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
k_sleep may not be enough to let advertiser send the message. Instead we
should rely on the bt_mesh_send_cb.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
As part of TinyCrypt deprecation process (#79566) this commit
removes usage of this library from the JWT subsystem and its
related tests.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Test was marked build only with filters in each scenario looking for
sdl-dc which is only available on native_sim, so cut the chase and use
platform_only to narrow things down to native_sim directly instead of
building the world to get information we already know.
reduces build/run time from 78s to 17s on invocation of twister with
default options, saves a ton more when running twister with --all.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add test for cbprintf_package_convert function which checks if
it correctly handles array that holds string lengths. When convert
function is used twice, at first to calculate size of the output
package and then to actually convert the package, array of string
lengths can be used to optimize operation by not calculating
string lengths twice. However, array may not be able to hold all
string lengths that are needed for that package. In that case,
string lengths that did not fit into the array will be calculated
twice, in both conversions.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
If we receive poll() error during a request, it must
be forwarded to application.
If instead receive poll() error later, it should not be
forwarded as it might be result of application closing the
socket.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Refactor the CoAP retry handling into the handle_poll() function,
so that we only try to send retries if the socket reports POLLOUT.
Also move the receiving into same loop, so when poll() reports POLLIN
we recv() the message and handle it before proceeding to other sockets.
Also fix tests to handle POLLOUT flag and add support for testing
multiple clients.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Coverage for cmsis rtos APIS should is provided using simulation, we
should not build those on every platform we have. Avoid failures due to
incompatiblities in requirements coming from various boards and also
reduce churn and noise during testing and CI.
Fixes#80215
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The CAP tests used u_group->cig->index but the u_group->cig may
have been deleted when the stream is released, which meant
that u_group->cig == NULL when e.g. unicast_stop_complete_cb
was called and that could cause failing tests as the index
would just be a uninitialized value.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Change pins that are used for qdec nrf54h20dk to align with shield
(loopbacks) used in internal CI. This change is needed to start
qdec driver power management testing.
Signed-off-by: Piotr Krzyzanowski <piotr.krzyzanowski@nordicsemi.no>
sqrtf() is used for floats but the argument and resulting
variable are both doubles. LLVM would complain about
implicit conversion from float to double. So use sqrt()
instead as it is used with doubles.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The stream flash test has been written with SoC internal
storage in mind and its simplified structure does not take
into account possibility of existence of devices with
different erase characteristics, at run time.
The commit fixes the test failing with Nordic bords that
have CONFIG_SPI_NOR=y set by default, which made test
to behave like device with erase capability has been tested.
The commit sets CONFIG_SPI_NOR=n for nrf54l devices.
Fixes#79181
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Add log statements for each command, event and response
for debugging purposes.
Tests do not send enough of these to clutter the IUT logs
and it is useful for debugging to more easily determine
what command triggered a function call or when the
responses and events are sent to the AutoPTS client.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This commits defines the `#power-domain-cells` properties for fakedomain
nodes in the HiFive Unmatched devicetree overlay file.
Without this change, this tests fails to build for the `hifive_unmatched`
Zephyr target.
Fixes#80503.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
In 82d8f09de1
the bt_conn_foreach prototype was changed, but these unit tests
kept using the old prototype which leads to a build warning.
Let's fix the prototype in the tests.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This resolves some addressed comments in this PR
https://github.com/zephyrproject-rtos/zephyr/pull/77930
It adds as well a section in the documentation about some
recommendations to increase ZMS performance.
Signed-off-by: Riadh Ghaddab <rghaddab@baylibre.com>
Refactor the sample so that multiple advertising setup can
be reused in other sample if required. Bluetooth enable can
be in the sample that reuses the advertising setup.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit adds new tests for verifying the functionality of the board
and SoC extension feature.
It does so by defining:
- A new CPU cluster on an existing SoC
- Two new board variants on top of an existing board
The new board variants are defined on top of the existing `native_sim`
board, so that the following native_sim board targets are available for
the test.
Existing board targets:
- native_sim/native
- native_sim/native/64
Extended board targets:
- native_sim/native/one
- native_sim/native/64/two
The new CPU cluster is defined for the existing `an521` SoC.
Existing CPU Clusters on an521:
- cpu0
- cpu1
New CPU Cluster:
- cputest
For SoC tests the mps2 board is used.
This means that for testing, the following board targets using the an521
SoC are:
- mps2/an521/cpu0
- mps2/an521/cpu1
- mps2/an521/cputest
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The test implementation is based on a copy of the HFC multilink test.
The test verifies that the stack respects the reference counting of SDU
buffers when the L2CAP -EINPROGRESS feature is used.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
This is shorthand for random static addresses. It's similar to
`bt_addr_le_from_str`, but is a macro that results in an object literal,
making it more versatile and less verbose.
This macro only gives access to the first 255 random static addresses,
but this ought to be enough addresses for testing.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
The commit splits default FCB scenario into one with endmarker
enabled, the original one, and one with disabled.
This allows to test the FCB in cases when CONFIG_FCB_ALLOW_FIXED_ENDMARKER
is set and not set.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This commit fixes minor copyright issues and corrects the compatible of
gpio-stepper with the vendor name as zephyr
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
What is changed?
- Added a new mps3 board an552 for the soc corstone300.
The qualifier to build/run application with board mps3/an552 is
`mps3/corstone300/an552` for secure and
`mps3/corstone300/an552/ns` for non-secure.
- Added FVP variant to enable FVP testing with corstone300
and it uses the ARM FVP `FVP_Corstone_SSE-300_Ethos-U55`.
The qualifier to build/run application with FVP is
`mps3/corstone300/fvp` for secure and
`mps3/corstone300/fvp/ns` for non-secure.
- Note: the qualifier to build/run application with board mps3/an547
is now changed to
`mps3/corstone300/an547` for secure and
`mps3/corstone300/an547/ns` for non-secure.
How is it changed?
- Moved common code from mps3/an547 to corstone300.
- Renamed soc for an547 to corstone300 and added
a new soc corstone300/an552.
Why do we need this change?
- This enables FVP support and testing for corstone300.
- SOC/qualifier for mps3/an547 was renamed to reduce code redundancy
- A separate FVP variant was added for AN552 because, the TFM board
used for non-secure variant differs for FPGA and FVP.
TFM board `arm/mps3/corstone300/fvp` should be used when testing
AN552 with FVP and `arm/mps3/corstone300/an552` should be used when
testing with AN552 FPGA.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
Clock source is changed from RC_SLOW to RC_FAST_D256 in order
to improve clock precision and avoid tests failing due to
lower precision of RC clock (around 10%).
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
This ensures that enabling BT_CTLR_DTM does not break the compilation of
the Bluetooth shell.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Removed the LE Audio specific definition and instead
refer to the value defined by iso.h as it is ISO/Core
that defines this size, and not BAP/Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
There are issues with 64 bit compilation in hostap so disable
native_sim/native/64 board from the tests. The board will be
enabled again after updating the hostap from upstream and fixing
the issues.
Fixes#80437
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For tests that support both targeting unit_testing and
other targets, we check in the cmake code the BOARD variable.
Let's allow users to set this to either of unit_testing
or unit_testing/unit_testing so it behaves like for other
tests.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Fix filtering done in
22c3438f1b
Otherwise we end up with tests defined twice, as a .unit and .zerphyr
variant but both run in normal builds, and none for unit tests.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Use full board name in cmake file.
Akin to the fix done in
https://github.com/zephyrproject-rtos/zephyr/pull/80270/
following the changes from
https://github.com/zephyrproject-rtos/zephyr/pull/77250/
Note after the Zephyr cmake code has been run the BOARD
variable is split into BOARD BOARD_QUALIFIERS,
where BOARD does not contain the qualifiers anymore
(see cmake/modules/boards.cmake for more info).
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Removed the generation of broadcast id inside the stack. It is now up
to the application to generate this by itself. The CAP sample has
been modified to allow either a static broadcast, or a random one.
All of this is handled in the application.
Signed-off-by: Fredrik Danebjer <frdn@demant.com>
The 12-bit signed values for the results of PBR are a bit
cumbersome, so this adds a helper function to make it easier to work
with the HCI formatted steps.
Signed-off-by: Olivier Lesage <olivier.lesage@nordicsemi.no>
Add unit tests for bt_le_cs_step_data_parse.
Also exit early (without calling the function pointer) if the next
step would seem to read out of bounds.
Signed-off-by: Olivier Lesage <olivier.lesage@nordicsemi.no>
Adds a test to ensure that the LoRaWAN MCUmgr transport builds with
all options enabled and all options disabled
Signed-off-by: Jamie McCrae <spam@helper3000.net>
The peer remote device "source_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Instead of fixing csi2rx clock frequencies, set them according to the
pixel rate got from the camera sensor.
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "sensor_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
nrf54h20dk_nrf54h20_cpurad by default has less RAM dedicated for
DMA transfers and default 1k buffer cannot be used for
uart_async_long_buf case. Use custom value.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
One of the test case is performing long transfers using 1k buffers.
For some targets there may be not enough RAM to perform such
transfers. Make long buffer length configurable.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Adjust the testcase.yaml files to only allow running on native_sim.
These tests use mocking and are not meant to run on embedded platforms.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Fix the test for sending frames with the CAN_FRAME_ESI flag set. Sending
frames with this flag set in software is never allowed.
Fixes: 8023a58c2a
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Linter pass makes CI happy and keeps code compliant
with the stylistic guidelines of the project
Signed-off-by: Rafael Laya <rafael_laya97@hotmail.com.com>
This updates the documentation of all the NXP boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Added test to verify deferred ACL Tx transmission setup,
such that GATT discovery completes with least latency and
GATT notifications can be received earliest after connection
establishment.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The CONFIG_DUMMY_DISPLAY is now enabled in conjunction with devicetree,
So, no need to be explicitly enabled.
Remove the setting.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Replace OVERLAY_CONFIG with CONF_FILE since no-device-pm.conf
contains an alternative configuration to the one in prj.conf
Signed-off-by: Abderrahmane Jarmouni <git@jarmouni.me>
Rework overlays and add sysbuild/vpr_launcher folder to allow standard
test configuration for nrf54h20dk cpuppr.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Rework existing nrf54h20dk overlays to allow adding of
nrf54h20dk//cpuppr target.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
In order to allow fiting test in targets with smaller memory make
large buffer configurable through Kconfig.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
It will increase test coverage for adc driver, no test uses
ADC_GAIN_2_3 setting yet.
Signed-off-by: Bartlomiej Buczek <bartlomiej.buczek@nordicsemi.no>
Tests are checking error codes returned from adc_read() and
adc_channel_setup() used with invalid configurations.
Signed-off-by: Bartlomiej Buczek <bartlomiej.buczek@nordicsemi.no>
Try to compile test wifi with various configuration combinations.
This is trying to catch simple compilation issues in the PRs.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Added helper functions to set and get broadcast name
for codec capabilities and codec configs.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Implemented:
* Central sync to broadcaster, connects to peripheral and
transfers sync. Peripheral Syncs to PA
* Broadcaster acting Central connects to peripheral
and transfers sync. Peripheral sync to PA
* Moved previous bis tests to test_bis.c and
new PAST tests was added in test_past.c
Signed-off-by: Lucas Mathias Balling <lutb@demant.com>
If we get an error/rejection from the CAP acceptor when
performing the Unicast Audio Start or Stop procedure then
we need to abort the procedure and let the application determine
what the next step is.
This change triggered a corner case when connecting to multiple
CAP acceptors as the CAP initiatior. This was also fixed as part
of this.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Changed dependency of the BT_BAP_SCAN_DELEGATOR to GATT_DYNAMIC_DB
from 'select' to 'depends on' and solved all loop dependencies
caused by this change.
Fixes#79108
Signed-off-by: Babak Arisian <bbaa@demant.com>
The own_addr_type used for various HCI commands sometimes
had a BT_HCI_OWN_ADDR_* type value or a BT_ADDR_* type
value. Those are 2 different value spaces, and if the public
address types would ever change, it would start have incorrect
behavior.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The ILPS22QS is an ultra-compact piezoresistive absolute pressure sensor
which functions as a digital output barometer, supporting dual full-scale
up to user- selectable 4060 hPa. The device delivers ultra-low pressure
noise with very low power consumption and operates over an extended
temperature range from -40 °C to +105 °C.
(https://www.st.com/en/mems-and-sensors/ilps22qs.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Check error codes when sending invalid frames:
- too big data payload;
- wrong set of flags.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
There is negative test for too high data bitrate.
Add test that checks too low data bitrate.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
remove k_work related code and change
the argument of the callback to `struct net_socket_service_event`.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Use full board name in cmake file.
Akin to the fix done in zephyrproject-rtos#80270
zephyrproject-rtos#80270
following the changes from
zephyrproject-rtos#77250
In which twister now uses the full board name when calling cmake.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This commit does the following:
1. tests set_callback and user_data
2. fixes the api as well as the drivers by passing user_data
back to the set callback
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
This commit increases the test timeout for the wait queue benchmark tests
to 120 seconds because these tests frequently hit the default timeout of 60
seconds during execution.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
We now use hwmv2 to list boards instead of relying on twister specific
config files.
One yaml files (twister.yaml for now) will have all the data needed for
all possible targets and variations of a board reusing most of the data
where possible and variations can override the top level data.
Twister keeps track of 'aliases' of boards and identifies that for
example native_sim is the same as native_sim/native, so either names
will be possible in both test yaml files or on the command line,
however, the reporting will always use the full name, so no there is no
confusion about what is being tested/built.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Transactions should result in a single transfer call not multiple
transfer calls. Transceive isn't supported by i2c and so the TXRX op
isn't validated for success anymore.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add overlay for APARD32690 board and add a new test case to
test RTIO functionalities of SPI MAX32 driver.
Signed-off-by: Dimitrije Lilic <dimitrije.lilic@orioninc.com>
The Thrift module tests were under the "newlib" namespace, presumably
because newlib was the default at the time of their introduction.
Since newlib is no longer the default libc and Thrift is not being tested
against multiple C libraries, this removes the libc type from the Thrift
test identifiers.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Enable flash driver test for MAX32690 boards.
Signed-off-by: Mert Vatansever <mert.vatansever@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Add support for building and running the BT tester on the
nrf5340_audio_dk.
This is copying the configuration used for the nRF5340 DK.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Test was failing because after re-enabling QDEC there is an interrupt
REPORTRDY coming after some time. Test had k_msleep(100) added to
accomodate for that but it was added after sensor_sample_fetch and
should be added before so that sample with data from REPORTRDY event
is fetched so that next read is empty as expected.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
This patch adds tests for the wifi_credentials library.
Both the main functions and the backend implementations are tested.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Added the battery critical status char to bas service
as per bas_1.1 spec. Updated BSIM test for BAS service
to test the INDs of BAS critical characteristic.
Signed-off-by: Nithin Ramesh Myliattil <niym@demant.com>
This makes sure we always fit all configurations. Worst case is two
audio streams in 48_6 configuration in single ISO channel (2x155).
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
For now this seems to be required by PTS as there is not Upper Tester
action for this in Test Specification.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Add wsen_hids_2525020210002 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Add support for Bosch bmp390 sensor, the drop in replacement for the
bmp388 with same register but different chip-id. This patch make use
of "bosch_bmp390" or "bosch_bmp388" and set the specific chip-id in a
data->chip-id variable, which then used to check against the register
value.
Additional, manual shift operation had been replaced with ENDIAN safe
macros and calibration values with target variable of int16_t add a
cast for it.
bmp388_spi: read register implementation wrong, fixed it.
tx-buffer must be <addr><dummy><dummy> in order to receive the
register value. Read registers in burst mode and have rx and tx
buffer same spi_buf to avoid clock stop and delay with nrf5.
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
Add test suite which uses GPIO loopback to produce a "very low" and
"very high" voltage at the positive input of the comparator using the
output of a GPIO. The negative input is set to a voltage between the
high and low output voltages of the GPIO using whichever internal
reference is available to the comparator.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Add functionality to test the IGMP query handling. This test should
prevent the IGMP logic from sending IGMPv3 messages to IGMPv2 queriers.
The test does now also check backwards compatability when IGMPv3 queries
are received but only IGMPv2 is enabled.
Signed-off-by: Ibe Van de Veire <ibe.vandeveire@basalte.be>
In a uniprocessor system, _sched_spinlock may not need to be
held in all the same cases that it does in a multiprocessor
system. Removing those unnecessary usages can lead to better
performance on UP systems. In the case of uncontested taking
and giving of a semaphore, this can be as much as a +14%
performance gain.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
The production version of the nRF54L15 SoC is now available, so remove
the initial Engineering A (EngA) preview version.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A bunch of copy-paste mistakes when adding the nRF54L15 DK added stale
references to the Preview DK (PDK).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a test that checks behavior of
CONFIG_BT_CONN_CHECK_NULL_BEFORE_CREATE Kconfig option.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Some devices may belong to >1 power domain, so with the current design
this is something not possible to describe. It's worth to note that
Linux also uses the `power-domains` naming scheme, not `power-domain`.
This patch also introduces `power-domain-names` so that each entry in
`power-domains` can be given a name if needed. `#power-domain-cells`
is now required as well.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Change integration_platform -> platform_allow to not build the
shell test suite for all supported boards.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
retained_mem driver is now compatible with nrf54h20 cpuapp & cpurad.
Also add missing .conf for nrf54l15.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Tests for prometheus library support.
It contains integration and unit test
each metric types.
Signed-off-by: Mustafa Abdullah Kus <mustafa.kus@sparsetechnology.com>
Enable dma boards/test for S32Z270.
The non-cacheable memory used for DMA tests (chan_blen_transfer and
loop_transfer) is split from the system SRAM.
Signed-off-by: Ha Duong Quang <ha.duongquang@nxp.com>
Consistently use the nRF54L15 as the non-TF-M integration platform
in addition to `native_sim`, and the nRF9151 as the TF-M one.
In addition, add the `integration_platforms` specification to the
tests that were missing it.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Fix errors found in CI for missing clock_t and clockid_t types
when building the tests/posix/net testsuite against newlib.
Also use angle-brackets and prefixed path with
`<zephyr/posix/posix_types.h>` since it is not in the default
search path and is analagous to `<sys/types.h>`.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
It's more common (and more readable) convention to use lower-case
names for string-based device tree property values. Convert the HCI bus
and quirks to follow this convention. Also take advantage of the
recently added support for string-array enums to enforce that the
correct values are used.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
