Some ADCs (e.g. SAM0) can only convert one channel at a time
and therefore need to be reconfigured for every voltage
divider prior to startin the conversion
Signed-off-by: Patrick Günzel <patrick.guenzel@kinexon.com>
Move the Atmel SAM E70/V71 DMA PERIDs header file to
include/zephyr/dt-bindings/dma and unify it for use with the entire product
family (SAM E70/S70/V70/V71).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Synchronize the Atmel SAM E70/V71 DMA Peripheral Hardware Requests HW
Interface Numbers and adjust them to match those listed in the SAM
E70/S70/V70/V71 datasheet.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
JLink refuses new RTT telnet connections for a few moments after a socket
closes. This causes an issue when using `nc` as the telnet viewer, since
JLink would deny the connection. To resolve this, keep the "ping" socket
we use to determine if the RTT viewer is active connected, and use that
socket for RTT communication.
Signed-off-by: Daniel DeGrasse <ddegrasse@tenstorrent.com>
end frame is used to supply clock pulses so that data goes to last
LED in the chain. Thus, it depends on the number of LEDs in the chain.
Previously, the number of ones sent into the end frame was
hard-coded and limited the usage of the driver to 64 LEDs in the
strip.
Signed-off-by: Cyril Fougeray <cyril.fougeray@toolsforhumanity.com>
Move the SAM V71 register name fixup from the SoC code into the PWM driver
next to the other PWM driver fixup.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Sort the Atmel SAMx7x periheral devicetree nodes according to their address
in the memory map.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add the PWM LED to Nucleo-WB07CC board and mark as compatible with PWM.
Also mark counters as supported (but don't enable by default).
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add the PWM LED to Nucleo-WB05KZ board and mark as compatible with PWM.
Also mark counters as supported (but don't enable by default).
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add the PWM LED to Nucleo-WB09KE board and mark as compatible with PWM.
Also mark counters as supported (but don't enable by default).
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
This commit adds support for the STM32WB0 series to
the existing STM32 timer-based counters driver.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Update infineon assets
- abstraction-rtos to 1.8.1.41337
- core-lib to 1.4.2.41337
- mtb-hal-cat1 to 2.6.2.44607
- mtb-pdl-cat1 to 3.12.1.37059
- mtb-template-cat1 to 1.3.0.35366
- serial-flash to 1.4.2.35289
SHA: 468e955eb49b8a731474ff194ca17b6e6a08c2d9
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
The Atmel SAM0 SoC enable peripherals clocks in distinct places: PM and
MCLK. The old devices had defined the peripheral clock enable bit at PM.
On the newer devices this was extracted on a dedicated memory section
called Master Clock (MCLK). This change excludes the dedicated bindings
in favor of a generic approach that cover all cases.
Now the clocks properties is complemented by the atmel,assigned-clocks
property. It gives the liberty to user to customize the clock source
from a generic clock or configure the direct connections.
All peripherals drivers were reworked with the newer solution.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Some platforms require special clock selection options. This could be
made using the already defined assigned-clocks from Linux clocks.
See 93ee800895/dtschema/schemas/clock/clock.yaml (L24)
This introduces the vendor atmel,assigned-clocks and
atmel,assigned-clock-names properties to generalize those conditions
in Zephyr for Atmel sam0 SoC series.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add new SENSOR_CHAN_FREQUENCY constant to allow implement sensors that
output frequency values in Hertz.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
This commit adds two properties. One is used to set size of the low
flash device and the other is used to select the low flash device. Then,
the eSPI TAF request can access between two flash devices base on this
setting.
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
Add support for the I2C_MSG_RESTART flag to be able to use a
repeated start in between chained transactions.
The driver now uses the stop/restart flags set in the i2c_msg,
instead of starting and stopping for each transaction in the chain.
Signed-off-by: Lorenz Clijnen <github@lorc.be>
The number of mpu regions that can be configured is less than four cases.
Therefore, only remove this case on cm33 cores, failed log show below:
"num_parts of 4 exceeds maximum allowable partitions (3)"
samples: kernel: mem_protect: userspace: remove mimxrt700_evk cm33 cores
The maximum number of partitions is less than the number of partitions
currently required, causing case to be unable to apply for or delete
excess regions.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
update gpio driver to adapt rt7xx gpio model:
1. There is no PORT_Type on RT7xx,so set PORT_Type as void
2. Add port_no parameter in gpio_mcux_config to adapt IOPCTL driver
3. Add gpio-port-offest parameter in blinding, it will help map the
relation between index n and gpio port when some soc have domain
access attribution.
3. Splite gpio_mcux_configure function into two functions(
gpio_mcux_iopctl_configure and gpio_mcux_port_configure)
according to CONFIG_PINCTRL_NXP_IOCON macro
4. Add code to adapt RT700 GPIO attribute configuration
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
Define iocon array to store iocon base address
add index parameter support to support multi iocon instances
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
The LLEXT Extension Development Kit, mostly implemented in
'cmake/llext-edk.cmake', is already part of the 'llext' area of the
MAINTAINERS file, but its test is currently unowned.
Add the missing directory to the 'llext' area.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Recently, the "Generated zephyr.dts" message started being shown twice,
because of some now redundant code that was left behind by commit
fe3287a9ac.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Marked the irq-gpios property as "required: true" in the yaml file.
This ensures that the property is always defined in the device tree,
preventing the driver from crashing when irq-gpios is missing.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Currently the timer_behavior test uses fabs.
Since the C library functions being used in the kernel
is restricted in Rule A.4 in the Coding Standard
We should probably not use these functions in tests either.
Signed-off-by: Robin Kastberg <robin.kastberg@iar.com>
What is the change?
- Fixes#83660 allowing device to now enter suspend mode even if
CONFIG_DEBUG_THREAD_INFO is enabled.
Why is this needed?
- z_sys_post_kernel was cleared as part of #d778d5c
to "allow debuggers to display the correct thread state after
the first 3 instructions have run".
This is not required while resuming from suspend and
it prevents the device from entering suspend so,
move it out of resume path.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
The DMA-based path of the lpspi driver is basically
almost a driver of it's own, move it to it's own file.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
There is (almost) a whole separate driver for RTIO,
move this code to its own file and move shared code
and definitions to a common file.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Move this driver to its own subfolder to organize it
since there will be new files added for this hardware.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
