The reset pulse is currently fixed at 1 µs, the minimum required for
the chip. However, a long reset pin trace can increases rise time, making
1 µs potentially insufficient for reliable detection of a reset signal.
Increase the pulse duration to 2 µs
Signed-off-by: Igor Knippenberg <igor.knippenberg@gmail.com>
Refactor and merge the SoC support files for the Atmel SAM E70 and SAM V71
product series. These SoCs are part of a larger product family (SAM
E70/S70/V70/V71) and share a common set of peripherals.
Support for the two remaining product series (SAM S70/V70) is not part of
this refactoring as these will require further additions to the Atmel HAL.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
update gpio driver to adapt rt7xx gpio model:
1. There is no PORT_Type on RT7xx,so set PORT_Type as void
2. Add port_no parameter in gpio_mcux_config to adapt IOPCTL driver
3. Add gpio-port-offest parameter in blinding, it will help map the
relation between index n and gpio port when some soc have domain
access attribution.
3. Splite gpio_mcux_configure function into two functions(
gpio_mcux_iopctl_configure and gpio_mcux_port_configure)
according to CONFIG_PINCTRL_NXP_IOCON macro
4. Add code to adapt RT700 GPIO attribute configuration
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
Add a GPIO driver for the Microchip MEC5 HAL based chips.
Current devices are: MEC174x, MEC175x, and HAL version of
MEC172x named MECH172x.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Set up a named device MMIO memory mapping in the GPIO controller's
parent device, map the virtual memory in the init function of the
parent device.
Once the controller's register space has been successfully mapped,
propagate the mapped virtual address to all child (= GPIO bank)
devices. While it is possible to add a named mapping to every
single GPIO bank device and initialize it in the respective bank
device's init function, this would result in multiple virtual
address mappings all pointing to the same 4k of physical memory.
I assume that, although all those mappings having the same attri-
butes, such a setup is at least discouraged.
Signed-off-by: Immo Birnbaum <mail@birnbaum.immo>
First commit to add support for gpio interrupt on Renesas RA
- Add support for external interrupt driver
- Add support for gpio interrupt config
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
After a non-power reset (wdt) pins may remain in non-default state.
To ensure that a system initialization is the same after any reset,
it is necessary to initialize pins to the default state.
Signed-off-by: Mikhail Siomin <victorovich.01@mail.ru>
Map MMIO memory by using DEVICE_MMIO_NAMED_x() APIs.
And some platforms has no soc.h, so use __has_include to check it
firstly.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Add max22190 gpio driver with input functionality, since device
support only input without output.
Implemented diagnostic functionality for all 8 channels
which include various check to over/under voltage and wire break.
Filtering configuration is done from devicetree on per channel
bases and is configured on chip start.
In case some fault condition occure FAULT pin drive LOW which
prop to FAULT registers to be read. Data is stored in data structure
for furter analizes and ERR message is printed in console.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
These device driver APIs were merged after the DEVICE_API macro was
introduced.
Cleanup these leftover drivers.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Compilation will fail if multiple models are used at the same time.
Changing to define different unique names for the symbols
to avoid conflicts.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add support for GPIO controller feature of AW9523B.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Co-authored-by: Benjamin Cabé <kartben@gmail.com>
The `Kconfig.defconfig` is not good place for put `select PINCTRL`.
Drop `select PINCTL` from `Kconfig.defconfig` and add it at each
driver's Kconfig.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
To remove CONFIG_PINCTRL from board side for numaker boards.
The Drivers using Pinctrl should be turning Pinctrl on
instead of the responsibility of the board.
Fixes#78619
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Flags added allow keeping a pin as input/output by not disabling
the output buffer when configuring it as an input and by not
disabling input enable when configuring it as output. This can
be useful to implement signal diagnosis or for testing purposes.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
-Update formatting and contents of index.rst for cy8ckit_062s4
-Update formatting and contents of index.rst for cy8ckit_064s0s2_4343w
-Update formatting and contents of index.rst for cy8cproto_062_4343w
-Update formatting and contents of index.rst for cy8cproto_063_ble
-Update formatting and contents of index.rst for xmc45_relax_kit
-Update formatting and contents of index.rst for xmc47_relax_kit
-Change all instances of "PSoC" to "PSOC" for infineon platforms
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
This patch allows to _safely_ configure GPIO ports that have their pad
on FAST_ACTIVE1 domain.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
It's not possible to get pinconfig of specific pin
in ambiq_gpio_port_get_raw function, change to use
OR value of RD and WT registers for one group of gpio.
Signed-off-by: Hao Luo <hluo@ambiq.com>
The sys_write32 function expects a value as the first parameter and the
memory location where the value should be written as the second parameter.
Signed-off-by: Nils Bosbach <bosbach@ice.rwth-aachen.de>
Implement the parallel mode in the powertrain switch TLE9104.
This allows that OUT1 and OUT2 are controlled together, as well
as OUT3 and OUT4.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
The Drivers using Pinctrl should be turning Pinctrl on
this should not be the responsibility of the board. This
commit removes CONFIG_PINCTRL from the boards side for nxp boards.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Industrial 8 channel output with advanced diagnostics.
Allowing giagnostic configuration both on per channel or global bases
In SPI communication diagnostic status transmitted on every
READ/WRITE which includes generic status of chip.
Diagnostics includes :
* Oveload
* Open Wire
* Over current
* Short to VDD
* Thermal Shutdown
* VDD Warn
* Watch Dog Error
* Communication Error
* VDD under voltage
Add app.overlay for MAX14916 driver.
Tested with adopted basic/blinky example.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
MAX14906 in 4 channel I/O with advanced diagnostic.
In SPI communication diagnostic status transmitted on every
READ/WRITE which includes generic status of chip.
Configuration both on global level and on per channel bases.
Diagnostics includes :
* Thermal overload
* current limit
* open wire detection
* short to VDD
* Above VDD
* Safe DEmagnitization fault
* VDD warning
* VDD low
* SPI/CRC Error
* WDog Error
* Loss GND
Add app.overlay for MAX14906 driver.
Tested with adopted basic/button and basic/blinky sample.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
Since the log module entity is not defined anywhere,
LOG_MODULE_REGISTER should be used here instead of LOG_MODULE_DECLARE.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Update the GPIO driver to use PDL API instead of HAL API to fix the
issue with configuring interrupts on both edges
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
The driver enables the clock of a gpio-port if any of the
pins use the port. This is done by calling pm_device_runtime_get
when a pin is used and pm_device_runtime_put when the pin is not
used anymore.
These calls needs to be balanced. But if a single pin was configured
as GPIO_DISCONNECTED multiple times, every time pm_device_runtime_put
was called.
This caused the clock of the port to be stopped and therefore also
other pins on the same port stopped working.
This commit fixes this by keeping track of which pin on a port
has requested the clock and only call pm_device_runtime_get or
pm_device_runtime_put when the clock-request for the specific pin
changes.
Fixes#77698
Signed-off-by: Jeroen Broersen <jbroersen@interact.nl>
