Add missing braces to comply with MISRA C:2012 Rule 15.6 and
also following Zephyr's style guideline.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
After flashed EC image, we needed to manually press the reset button
on it8xxx2_evb. Now, without pressing the button, we can disable
debug mode and trigger a watchdog hard reset for running tests.
After flash EC, running below tests can pass (without pressing the button):
west build -p always -b it8xxx2_evb tests/drivers/watchdog/wdt_basic_api
west build -p always -b it8xxx2_evb tests/kernel/timer/timer_api
west build -p always -b it8xxx2_evb tests/kernel/fatal/exception
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
In the it8xxx2 chip, the interrupt for INT0 is reserved. However,in some
stress tests, the unhandled IRQ0 issue occurs. To prevent the system from
going directly into kernel panic, we implemented a workaround by
registering interrupt number 0 and doing nothing in the IRQ0 handler.
The side effect of this solution is that when IRQ0 is triggered, it will
take some time to execute the routine. There is no need to worry about
missing interrupts because each IRQ's ISR is write-clear, and if the
status is not cleared, it will continue to trigger.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Pull more function into ram code section to effectively improve
access speed and performance.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The AIVECT (All Interrupt Vector Register) register provides us a quick
way to determine SOC interrupt number. But sometimes we get interrupt
number 0 from the register and caused assertion of unhandled interrupt.
To avoid the assertion, we look for all ISRs (Interrupt Status Register)
and IERs (Interrupt Enable Register) to find the highest priority pending
interrupt and return it to caller.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
We put disabling SOC interrupt enable register (IER) sequence in
between disable and enable core's global interrupt to prevent race
condition.
After core interrupt enable instruction has been executed, the new
configuration of IER has not yet been fully processed due to
asynchronization between core and SOC's source clock.
If SOC interrupt is fired under the above condition, we will get
IRQ number 0 in ISR due to IER disabling taken effect.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Don't leave idle state if soc isn't waked-up by an interrupt.
(We change to check interrupt controller register)
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Implement the CPU idle task. The system should enter this task when
there is no any task to ensure power saving.
Tested on it8xxx2_evb board. It will reduce 12.5mA when system enters
the CPU idle task.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Code removed:
- IT8XXX2 doesn't support soc level software interrupt hence remove
them.
- To use common macro to access csr (control status register).
- To remove CONFIG_RISCV_HAS_PLIC related code. IT8XXX2 uses its own
interrupt controller code.
- To remove ite_write and ite_read. We don't use them anymore.
Code changed:
- Return true from arch_irq_is_enabled() when external interrupt-enable
bit, and SOC's IER are both true.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Interrupt polarity register don't support rising and
falling edge triggered at the same time, so I correct
logic operation to match this.
Signed-off-by: Ruibin Chang <ruibin.chang@ite.com.tw>
Because these two functions are called from threads and ISR.
And they run a bit-wise OR operation on the interrupt registers.
So protect them to prevent race condition between thread and ISR
context where causing an interrupt won't enable as expected.
eg.
- Pseudo code of thread enable IER1's bit1:
1. load word from IER1 (0x40) and write into CPU register S1
=> S1=0x40
2. Or S1's bit1
=> S1=0x42
(But if an interrupt is triggered here)
3. Store word to IER1 from S1
=> IER1=0x42
(IER1 will be 0x42 not 0x43, IER1's bit0 is disable again due to the
race condition above)
-Pseudo code of ISR enable IER1's bit0
1. load word from IER1 (0x40) write into CPU register S2
=> S2=0x40
2. Or S2's bit0
=> S2=0x41
3. Store word to IER1 from S2
=> IER1=0x41
4. Go back to thread.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
This change ensures the CPU won't get an interrupt number which is
being generated.
it8xxx2 has a limitation for interrupt vector register.
CPU may read incorrect interrupt number in ISR.
The following is an example that got incorrect interrupt number:
1. Register IVECT = 0x10. (no interrupt pending/IVECT_OFFSET_WITH_IRQ)
2. Chip INT6 interrupt occurs (IVECT = 0x16) and jump to ISR.
3. Read interrupt vector register to determine interrupt number.
4. Higher priority interrupt occurs (for example: INT158, IVECT = 0xAE)
while the CPU is reading the interrupt vector register for EC INT6,
CPU may end up with an incorrect interrupt number between 0x16 and 0xAE.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
We need to clear interrupt status, before we enable the interrupt.
So I let ite_intc_isr_clear() to be global function.
Signed-off-by: Ruibin Chang <ruibin.chang@ite.com.tw>
This change enables A, C, D, E, G, H, I, J, K, and L groups,
and fix gpio interrupt function.
This change also pull (and rename) dt-bindings/irq.h to
dt-bindings/interrupt-controller/ite-intc.h, because it is
chip-specific.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Change-Id: Ifee039981c2cc4cf5980e663702a9921e629fc1e
