In case connection fails, the driver should raise a connect result event
to notify the user.
Signed-off-by: Toon Stegen <toon@toostsolutions.be>
Signed-off-by: Bart De Vos <bart.devos@verhaert.com>
Support setting WPA3 enterprise security mode in scan result, i.e.,
Suite-B, Sute-B-192 and WPA3 enterprise only mode.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
Mostly a revert of commit b1def7145f ("arch: deprecate `_current`").
This commit was part of PR #80716 whose initial purpose was about providing
an architecture specific optimization for _current. The actual deprecation
was sneaked in later on without proper discussion.
The Zephyr core always used _current before and that was fine. It is quite
prevalent as well and the alternative is proving rather verbose.
Furthermore, as a concept, the "current thread" is not something that is
necessarily architecture specific. Therefore the primary abstraction
should not carry the arch_ prefix.
Hence this revert.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Move the cmake file of OSAL to it's own repo and build as a standalone
library, this is porting friendly.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The "nm_bsp_reset" is used to apply a hard reset to the WINC board by
setting CHIP_EN and RESET_N signals low,then after specific delay
the function will put CHIP_EN high then RESET_N high.
reset-gpio is however defined as active low , causing this function
to hold the wifi module in reset.
Signed-off-by: Andreas Ålgård <aal@ixys.no>
The osal apis spinlock - take, release and bus qspi sleep
are trying to use ops after deinit. So removing osal deinit
for temporary workaround.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Add variable network configuration control into the driver to optimize
RAM usage by default. The pool sizes are default, and tuning is left to
the applications or samples.
Signed-off-by: Triveni Danda <triveni.danda@nordicsemi.no>
Start and stop SAP, the IPv4 address is not removed, if then use STA
mode to connect to EXT-AP with same gateway address as the stopped
SAP, STA will not get the DHCP IPv4 address, as the DHCP offer packet
is dropped due to detect of IPv4 address conflict. Removing SAP IPv4
address when stopped SAP can fix this issue.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
Convert vendor specific **_WIFI_BUILD_ONLY_MODE symbol as global
in order to provide common build flag to enable CI with no blobs.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Mode 0 cannot establish a connection when used as a UDP server,
replace mode 0 with mode 2 to save the client's IP and port as
the communication address when a message is received.
Fixes#82898
Signed-off-by: Hongquan Li <hongquan.prog@gmail.com>
Default enable WIFI_NM for both supplicant and embedded supplicant
case, to distinguish STA and SAP interface when use L2 layer.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
This commit aims to improve the integration of `esp_wifi_drv` by
providing the link mode information to `wifi_mgmt` when a station device
is connected to the AP.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Use HEAP_MEM_POOL_ADD_SIZE_ to add heap for NXP Wi-Fi. For supplicant
case, define less heap, as CONFIG_HEAP_MEM_POOL_ADD_SIZE_HOSTAP and
CONFIG_HEAP_MEM_POOL_ADD_SIZE_SOCKETPAIR are also enabled.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
Set TWT response parameters to zero to avoid
uninitialized values and ensure correct behavior.
Signed-off-by: Triveni Danda <triveni.danda@nordicsemi.no>
No need for an extra step to enable feature in the driver as it clearly
depends on the supplicant feature.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Add cancel action wait ops to cancel remain on channel after TX on
specific channel, in case we need to remain on another channel later.
Signed-off-by: Fengming Ye <frank.ye@nxp.com>
Added support for SPI in 4-wire and 3-wire configurations to
the Infineon AIROC WiFi driver (drivers/wifi/infineon).
Review changes:
Move DT_DRV_COMPAT to common header file
Correct board-specific preprocessor lines
Removed AIROC_MAP_COUNTRY_CODE
Move Pico W configuration details to devicetree
Use pinctrl to manage shared data/interrupt GPIO
Clean up bus selection in Kconfig.airoc
Make SDIO and SPI bus struct independent
Replace LOG_DBG with LOG_ERR
Remove functionally duplicate operation
Remove spurious Kconfig option
Minor cleanup in CMakeLists.txt
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Latest hostap (through upmerge) has intdocued a separate data
structure for signal info, so, fix the build errors. Also, fix the
variable rename for current TX rate.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The nrf wifi drivers include code related to qspi/spi bus. This work
moves bus related files to a new nrf70 bus library which is now
independent of the core driver and facilitlates building applications
directly using the bus APIs, agnostic to enabling wifi configs.
Signed-off-by: Bansidhar P.M <bansidhar.mangalwedhekar@nordicsemi.no>
Remove NRF_WIFI_RPU_RECOVERY_PROPAGATION_DELAY_MS Kconfig
which was defined twice with different values.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
The blobs are now part of nrf_wifi module, and remove the manual check
and add verifying the blobs and their integrity using helper function.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
