Add TI OMAP interprocessor mailbox nodes for AM62X A53,
the user ID assignment is as per thec corresponding mailbox
interrupt assignment for the core. Also while at it update the
supported feature list in corresponding boards.
More details can be found in the device TRM Mailbox section:
https://www.ti.com/lit/ug/spruiv7a/spruiv7a.pdf
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Remove hard-coded clock values from device tree nodes,
instead read the clock values from the clock controller
during run time.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
Rename "nxp,kinetis-lpuart" compatible to "nxp,lpuart" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The HAL configuration binding can be done dynamically based on the
IP's address space. The `hal-cfg-index` property is more tied to
software rather than hardware so remove it as an attempt to clean
up the binding.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Added XGMAC0, XGMAC1, XGMAC2 device nodes in
intel_socfpga_agilex5 dts file with default
parameter values and default device node status
as 'disabled'.
Signed-off-by: Santosh Male <santosh.male@intel.com>
Enabled ENET ethernet port on Cortex-A Core for imx8mn EVK board.
Updated document for supported features.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Enabled ENET ethernet port on Cortex-A Core for imx8mm EVK board.
Updated suported featues in board document.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Currently imx8mm/n use pinctrl binding of nxp,imx8m-pinctrl.yaml which
is used for imx8mq series platforms, but imx8mm/n have different pinctrl
hardware module with imx8mq, so change imx8mm/n to use binding of
nxp,imx8mp-pinctrl.yaml as imx8mm, imx8mn and imx8mp have the same
pinctrl hardware module.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Add mfd_adp5585 and gpio_adp5585 driver. This driver enables ADP5585
as an GPIO expander.
This chip is used as an GPIO expander on i.MX93 EVK. GPIO pinctrl,
read/write and interrupt is supported.
Note that ADP5585 has 2 GPIO banks with 5 pins each. The driver combines
two group into a 16-bit port. Index 0~4 correspond to R0~R4 lines, index
8~12 correspond to C0~C4 lines. Index 5~7 is reserved unavailable.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Add basic functionality of Renesas SD/MMC driver. It can be used
for both gen3 and gen4 R-car boards, but tested only with H3ULCB,
Salvator XS M3 and Spider boards. This driver working with SDHC
subsystem.
The driver supports regularal reading/writing throught SD/MMC
controller buffer, DMA mode w/o interrupts and timing tuning.
Add gpio5 and sd0 nodes to h3ulcb and salvator xs which are needed
for working with SD cards. The GPIO node is needed for switching
voltage on SD card through gpio regulator driver.
Notes:
* the driver doesn't support SPI mode;
* SCC tuning and DMA mode based on IRQs are enabled by default;
* an address of a data buffer has to be aligned to 128 bytes if it
is not, driver will use non-DMA mode automatically;
* Renesas MMC DMAC doesn't support 64-bit DMA addresses, so for
case when we have 64-bit xref data address we use non-DMA mode;
* SD/MMC controller supports block size between 512 and 1 with
a lot of restrictions, more details you can find in code;
* support of HS400 mode isn't implemented inside driver.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
Enable serial communication through UART port between HDMI ports.
Signed-off-by: Myeonghyeon Park <myeonghyeon@tsnlab.com>
Signed-off-by: Junho Lee <junho@tsnlab.com>
Squash the two copies of this file found in `dts/arm` and `dts/arm64`.
Their contents were identical up to devicetree property ordering.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
add dts support for watchdog to accomodate watchdog driver bringup on
aglex and agilex5
Signed-off-by: Balsundar Ponnusamy <balsundar.ponnusamy@intel.com>
i.MX93 share similiar register layout with i.MX RT11xx. Change ccm driver
to align with i.MX RT11xx, and make it easier to enable other drivers.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
