Add support for the `--erase` option on `west flash`, for boards that
specify at least one `--cmd-erase` option.
Signed-off-by: Jordan Yates <jordan@embeint.com>
JLink refuses new RTT telnet connections for a few moments after a socket
closes. This causes an issue when using `nc` as the telnet viewer, since
JLink would deny the connection. To resolve this, keep the "ping" socket
we use to determine if the RTT viewer is active connected, and use that
socket for RTT communication.
Signed-off-by: Daniel DeGrasse <ddegrasse@tenstorrent.com>
Add an argument `--esp-encrypt` to flash an ESP32 series chip with
encrypted flash.
The content of the binary is encrypted on the fly by the chip. It is
not required to know the encryption key. However, the fuses that
disable encrypted flash download must be kept enabled for this to work.
Signed-off-by: Martin Jäger <martin@libre.solar>
The Espressif branch of OpenOCD uses the version string "v0.12.0" instead
of "0.12.0" causing the version regex match to fail.
Add an optional 'v' prefix to avoid the failure.
Fixes: #83373
Signed-off-by: Eric Holmberg <eric.holmberg@northriversystems.co.nz>
Since "JLink.exe" is also an executable distributed with JDK's, do an
explicit search on the standard SEGGER install directories for a JTAG
"JLink.exe" before falling back to whatever is first on PATH.
Fixes#51825.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The cleanup pass (336c7da) to address long lines accidentally
removed a needed comma in the jlink runner.
Fixes#83605
Signed-off-by: David Leach <david.leach@nxp.com>
Instead of unconditionally erasing the whole target, add
support for using the common --erase flag.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
The ecpprog command is an utility written by Greg Davill for flashing
FPGAs such as ECP5 or CrossLink-NX series. Devkits typically have an
FTDI interface chip to access the external flash. FPGA image is
typically at flash offset 0x00000000 flash offset, and the Zephyr
image offset can be set via CONFIG_FLASH_LOAD_OFFSET.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Add new '--start-address' argument to the STM32CubeProgrammer west runner.
This argument can be used to specify an address from which the MCU should
start executing, instead of relying on the default value in CubeProgrammer.
Also update STM32CubeProgrammer runner tests to support new argument.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
This commit adds a runner wrapper for the 'minichlink' program which
offers a free, open mechanism to use the CH-LinkE programming dongle for
the CH32V003.
https://github.com/cnlohr/ch32v003fun/tree/master/minichlink
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
Commit e2a32d8b0ca596afeae48739c43817f693720a88 introduced an unbound
cmd issue for jlink flashing.
Fixed by moving cmd assignment outside of condition.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
These ignores were added with an older version of pylint and are
either removed or ignored by default.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Previously, rtt start would always fail because the target
(i.e. firmware) had not been started.
```
Info : rtt: Searching for control block 'SEGGER RTT'
Info : rtt: No control block found
```
When the command is 'rtt', run the binary via gdb before calling
'rtt start'. Firmware calls `SEGGER_RTT_Init()` shortly after
init which allows OpenOCD to find the RTT control block.
Similarly, only start the 'rtt server' after calling
'rtt start' to avoid any potential race conditions
internally within OpenOCD.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Previously, there was a warning that the to_num() method can
(and probably should) be unbound from OpenOcdBinaryRunner.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Similar to how print_gdbserver_message() prints GDB server info
when "west debug" is run, print RTT server info when "west rtt"
is run.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Netcat (nc) does not handle SIGINT. It silently ignores it.
We cannot use run_client(), given that the pydoc for
run_client() specifically contains "Run a client that
handles SIGINT".
Instead, use check_call(), which correctly handles Ctrl+C.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
