This commit adds support for ANY_MOTION and DATA_READY interrupts for
the BMI270. To implement this, a different config blob than the
"max_fifo" blob has to be used.
Signed-off-by: Benjamin Lindqvist <benjamin@eub.se>
This adds the i2c driver for the Renesas SmartBond(tm) MCU family.
It supports blocking transfers and callback transfers.
Currently only supports controller mode.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Under disk bindings. NVMe is a purely PCIe based technology, thus the
relevant includes.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Removed extra #includes at top of files. Missed closing } of
mec172xnlj.dtsi. Lower-cased 'reg' field of PWMs.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
This adds a driver for the DS2482-800 1-wire multi channel bus driver.
The driver uses a split architecture in order to share a common lock
among all configured channels of a single IC.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Add test for the experimental feature GPIO_ENABLE_DISABLE_INTERRUPT,
which covers APIs gpio_pin_interrupt_enable() and
gpio_pin_interrupt_disable().
Signed-off-by: Sung-Chi Li <lschyi@google.com>
Use the LTDC in combination with the DSI HOST makes the pinctrl obsolete.
DSI HOST has dedicated pins.
Signed-off-by: Rico Ganahl <rico.ganahl@bytesatwork.ch>
The driver has been recently moved under the input subsystem but the
corresponding driver was left over. Move it from kscan to input.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Give precision to the description of the dma phandle in the
quadspi node.
When a DMAMUX is present and enabled, the channel is the dma one
(not dmamux channel) and the request is given by the DMAMUX.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The emulated RTC device driver is used to emulate a real
RTC device. Note that it is not a replacement for the
native_rtc module, which is used to control simulated time,
get time from the host system, etc.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
This test suite adds tests for the following:
- Setting and getting time
- Validating time is incrementing correctly
- Validating behavior of alarms with callback disabled
- Validating behavior of alarms with callback enabled
- Validating update callback
The test suite uses the devicetree alias rtc to find
the device to test.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
Add optional filter value properties. The filter is disabled by default
but can be enabled by setting the filter-sample-period > 0 in the dts
file. A latency is introduced if the filter is enabled. The latency can
be printed by setting sensor log level to debug.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
This commit implements the temperature sensor interface for
the Maxim MAX31865 SPI Temperature Sensor.
Signed-off-by: Fin Maaß <fin.maass@haw-hamburg.de>
Co-authored-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Sort SoC nodes by address to make it easier to find them. As part
of this also move the intel-sha node under SoC where it belongs.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
In ACE 2.0 platform (LNL) ssp got new shim registers.
SSP driver need to program them to configure the interface.
This patch adds new shims to device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
As the power domain nodes don't represent something accessible via
a MMIO register move those under the lps node to address warnings
generated when building the DTS.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
LNL platform is ACE 2.0 series with changes in shim registers and HW
features. Initial definition replicates MTL as much as possible, however
it will vary after enabling LNL platform.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds definition of ACE 2.0 Lunar Lake board.board.
Signed-off-by: Krzysztof Frydryk <Krzysztofx.Frydryk@intel.com>
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adds the nodes for the GPDMA 1 & 2 peripherals
to the stm32h5 serie.
Each instance has 8 channels and 140 DMA requests.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Adds tmd2620 driver and devicetree bindings to work in
trigger and polling mode supporting Power management.
Signed-off-by: Peter Fecher <p.fecher@phytec.de>
Add LEDC device for esp32s3
Update PWM LED binding
Remove invalid comment from driver source file
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Added UART instances and changes to enabled
support for PCIe UART instances.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Enabled simultaneous support by adding a DTS variable named “io-mapped”.
There are 3 possibilities through instance in dtsi file.
Under PCIe, PCIe ns16550.
Under soc and has a variable io-mapped, legacy(IO mapped).
Under soc and don’t have a variable io-mapped, MMIO mapped.
Simultaneous access can be enabled by a Kconfig.
For PCIe instances UART initialization should be done post-kernel as it
depends on PCIe initialization.
Co-authored-by: Najumon BA <najumon.ba@intel.com>
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
