.. zephyr:board:: rzg3s_smarc Overview ******** The Renesas RZ/G3S SMARC Evaluation Board Kit (RZ/G3S-EVKIT) consists of a SMARC v2.1 module board and a carrier board. * Device: RZ/G3S R9A08G045S33GBG * Cortex-A55 Single, Cortex-M33 x 2 * BGA 359-pin, 14mmSq body, 0.5mm pitch * SMARC v2.1 Module Board Functions * LPDDR4 SDRAM: 1GB x 1pc * QSPI flash memory: 128Mb x 1pc * eMMC memory: 64GB x 1pc * PMIC power supply RAA215300A2GNP#HA3 implemented * microSD card x2 * I3C connector * JTAG connector * ADC x8 channels * Current monitor (USB Micro B) * Carrier Board Functions * Gigabit Ethernet x2 * USB2.0 x2ch (OTG x1ch, Host x1ch) * CAN-FD x2 * microSD card x1 * Mono speaker, Stereo headphone, Mic., and Aux.. * PMOD x2 * USB-Type C for power input * PCIe Gen2 4-lane slot (G3S supports only 1-lane) * M.2 Key E * M.2 Key B and SIM card * Coin cell battery holder (3.0V support) Hardware ******** The Renesas RZ/G3S MPU documentation can be found at `RZ/G3S Group Website`_ .. figure:: rzg3s_block_diagram.webp :width: 600px :align: center :alt: RZ/G3S group feature RZ/G3S block diagram (Credit: Renesas Electronics Corporation) Supported Features ================== The ``rzg3s_smarc/r9a08g045s33gbg/cm33`` board target supports the ARM Cortex-M33 System Core without FPU and the following hardware features: +-----------+------------+-------------------------------------+ | Interface | Controller | Driver/Component | +===========+============+=====================================+ | NVIC | on-chip | arch/arm | +-----------+------------+-------------------------------------+ | SYSTICK | on-chip | arch/arm | +-----------+------------+-------------------------------------+ | PINCTRL | on-chip | pinctrl | +-----------+------------+-------------------------------------+ | GPIO | on-chip | gpio | +-----------+------------+-------------------------------------+ | UART | on-chip | serial | +-----------+------------+-------------------------------------+ Other hardware features are currently not supported by the port. Programming and Debugging ************************* RZ/G3S-EVKIT is designed to start different systems on different cores. It uses Yocto as the build system to build Linux system and boot loaders to run BL2 TF-A on Cortex-A55 System Core before starting Zephyr. The minimal steps are described below. 1. Follow ''2.2 Building Images'' of `SMARC EVK of RZ/G3S Linux Start-up Guide`_ to prepare the build environment. 2. Before build, add ``PLAT_M33_BOOT_SUPPORT=1`` to meta-renesas/meta-rzg3s/recipes-bsp/trusted-firmware-a/trusted-firmware-a.bbappend. .. code-block:: bash :emphasize-lines: 6 require trusted-firmware-a.inc COMPATIBLE_MACHINE_rzg3s = "(rzg3s-dev|smarc-rzg3s)" PLATFORM_rzg3s-dev = "g3s" EXTRA_FLAGS_rzg3s-dev = "BOARD=dev14_1_lpddr PLAT_SYSTEM_SUSPEND=vbat" PLATFORM_smarc-rzg3s = "g3s" EXTRA_FLAGS_smarc-rzg3s = "BOARD=smarc PLAT_SYSTEM_SUSPEND=vbat PLAT_M33_BOOT_SUPPORT=1" 3. Start the build: .. code-block:: bash MACHINE=smarc-rzg3s bitbake core-image-minimal The below necessary artifacts will be located in the build/tmp/deploy/images +---------------+-----------------------------+ | Artifacts | File name | +===============+=============================+ | Boot loader | bl2_bp_spi-smarc-rzg3s.srec | | | | | | fip-smarc-rzg3s.srec | +---------------+-----------------------------+ | Flash Writer | FlashWriter-smarc-rzg3s.mot | +---------------+-----------------------------+ 4. Follow ''4.2 Startup Procedure'' of `SMARC EVK of RZ/G3S Linux Start-up Guide`_ for power supply and board setting at SCIF download (SW_MODE[1:4] = OFF, ON, OFF, ON) and Cortex-A55 cold boot (SW_CONFIG[1:6] = OFF, OFF, ON, OFF, OFF, OFF) 5. Follow ''4.3 Download Flash Writer to RAM'' of `SMARC EVK of RZ/G3S Linux Start-up Guide`_ to download Flash Writer to RAM 6. Follow ''4.4 Write the Bootloader'' of `SMARC EVK of RZ/G3S Linux Start-up Guide`_ to write the boot loader to the target board by using Flash Writer. Applications for the ``rzg3s_smarc`` board can be built in the usual way as documented in :ref:`build_an_application`. Console ======= The UART port for Cortex-M33 System Core can be accessed by connecting `Pmod USBUART `_ to the upper side of ``PMOD1_3A``. Debugging ========= It is possible to load and execute a Zephyr application binary on this board on the Cortex-M33 System Core from the internal SRAM, using ``JLink`` debugger (:ref:`jlink-debug-host-tools`). .. note:: Currently it's required Renesas BL2 TF-A to be started on Cortex-A55 System Core before starting Zephyr as it configures clocks and the Cortex-M33 System Core before starting it. Here is an example for building and debugging with the :zephyr:code-sample:`hello_world` application. .. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: rzg3s_smarc/r9a08g045s33gbg/cm33 :goals: build debug Flashing ======== Zephyr application can be flashed to QSPI storage and then loaded by Renesas BL2 TF-A running on the Cortex-A55 System Core and starting binary on the Cortex-M33 System Core. The Zephyr application binary has to be converted to Motorolla S-record `SREC`_ format which is generated automatically in Zephyr application build directory with the extension ``s19``. .. _SREC: https://en.wikipedia.org/wiki/SREC_(file_format) .. _Flashing on QSPI: Flashing on QSPI using Flash Writer --------------------------------------- Zephyr binary has to be converted to **srec** format. * Download and start **Flash Writer** as described in ''4.3 Download Flash Writer to RAM'' of `SMARC EVK of RZ/G3S Linux Start-up Guide`_ * Use **XLS2** command to flash Zephyr binary * Input when asked: .. code-block:: console ===== Please Input Program Top Address ============ Please Input : H'23000 ===== Please Input Qspi Save Address === Please Input : H'200000 * Then send Zephyr **s19** file from terminal (use ''ascii'' mode) * Reboot the board in the **QSPI Boot Mode** .. code-block:: console -- Load Program to SRAM --------------- Flash writer for RZ/G3S Series V0.60 Jan.26,2023 Product Code : RZ/G3S >XLS2 ===== Qspi writing of RZ/G2 Board Command ============= Load Program to Spiflash Writes to any of SPI address. Program size & Qspi Save Address ===== Please Input Program Top Address ============ Please Input : H'23000 ===== Please Input Qspi Save Address === Please Input : H'200000 please send ! ('.' & CR stop load) I Flash memory... Erase Completed Write to SPI Flash memory. ======= Qspi Save Information ================= SpiFlashMemory Stat Address : H'00200000 SpiFlashMemory End Address : H'002098E6 =========================================================== Flashing on QSPI using west --------------------------- Before using ``flash`` command, the board must be set to Cortex-M33 cold boot (SW_CONFIG[1:6] = OFF, OFF, ON, OFF, OFF, ON). After flashing, it must be set back to Cortex-A55 cold boot to run. The minimal version of SEGGER JLink SW which can perform flashing of QSPI memory is v7.96. **Note:** It's verified that we can perform flashing successfully with SEGGER JLink SW v7.98g so please use this or later version. .. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: rzg3s_smarc/r9a08g045s33gbg/cm33 :goals: build flash :compact: Troubleshooting =============== Linux and Zephyr application should not share SoC HW resources otherwise it will cause HW corruption and unpredictable behavior. Therefore, HW resources assigned to Zephyr application must be disabled in Linux. The below patch shows how to prevent Linux from configuring SCIF1 which is used by Zephyr. .. code-block:: diff diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi index f01801b18e8a..d9f9a0a2bb08 100644 --- a/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi +++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi @@ -347,7 +347,7 @@ &scif1 { pinctrl-0 = <&scif1_pins>; pinctrl-names = "default"; uart-has-rtscts; - status = "okay"; + status = "disabled"; }; #elif SPDIF_SEL == SW_ON &spdif { References ********** .. target-notes:: .. _RZ/G3S Group Website: https://www.renesas.com/us/en/products/microcontrollers-microprocessors/rz-mpus/rzg3s-general-purpose-microprocessors-single-core-arm-cortex-a55-11-ghz-cpu-and-dual-core-cortex-m33-250 .. _RZG3S-EVKIT Website: https://www.renesas.com/us/en/products/microcontrollers-microprocessors/rz-mpus/rzg3s-evkit-evaluation-board-kit-rzg3s-mpu .. _SMARC EVK of RZ/G3S Linux Start-up Guide: https://www.renesas.com/us/en/document/gde/smarc-evk-rzg3s-linux-start-guide-rev104