remove bad-whitespace pylint directive

README.rst

@@ -6,7 +6,7 @@ Introduction
     :alt: Documentation Status
 
 .. image:: https://img.shields.io/discord/327254708534116352.svg
-    :target: https://adafru.it/discord
+    :target: https://discord.gg/nBQh6qu
     :alt: Discord
 
 .. image:: https://github.com/adafruit/Adafruit_CircuitPython_DPS310/workflows/Build%20CI/badge.svg
@@ -73,16 +73,6 @@ Usage Example
         print("")
         time.sleep(1.0)
 
-Caveat: by default the library initializes the IC with constant temperature and pressure measurements at 64Hz with 64 samples. It is not possible to change the IC's mode, temperature_oversample_count or pressure_oversample_count on-the-fly so resetting the IC and operation parameteres is required. For instance, to set the mode to continuous pressure measurement at 1Hz with 2 samples:
-
-.. code-block:: python3
-
-    dps310.reset()
-    dps310.pressure_oversample_count = adafruit_dps310.SampleCount.COUNT_2
-    dps310.pressure_rate = adafruit_dps310.Rate.RATE_1_HZ
-    dps310.mode = adafruit_dps310.Mode.CONT_PRESSURE
-    dps310.wait_pressure_ready()
-
 
 Contributing
 ============

adafruit_dps310.py

@@ -64,7 +64,6 @@ _DPS310_RESET = 0x0C  # Soft reset
 _DPS310_PRODREVID = 0x0D  # Register that contains the part ID
 _DPS310_TMPCOEFSRCE = 0x28  # Temperature calibration src
 
-# pylint: enable=bad-whitespace
 # pylint: disable=no-member,unnecessary-pass
 
 
@@ -203,10 +202,6 @@ class DPS310:
 
     _calib_coeff_temp_src_bit = ROBit(_DPS310_TMPCOEFSRCE, 7)
 
-    _reg0e = RWBits(8, 0x0E, 0)
-    _reg0f = RWBits(8, 0x0F, 0)
-    _reg62 = RWBits(8, 0x62, 0)
-
     def __init__(self, i2c_bus, address=_DPS310_DEFAULT_ADDRESS):
         self.i2c_device = i2c_device.I2CDevice(i2c_bus, address)
 
@@ -238,9 +233,13 @@ class DPS310:
         self.initialize()
 
     def initialize(self):
-        """Initialize the sensor to continuous measurement"""
+        """Reset the sensor to the default state"""
 
-        self.reset()
+        self._reset()
+        self._read_calibration()
+
+        # make sure we're using the temperature source used for calibration
+        self._temp_measurement_src_bit = self._calib_coeff_temp_src_bit
 
         self.pressure_rate = Rate.RATE_64_HZ
         self.pressure_oversample_count = SampleCount.COUNT_64
@@ -249,35 +248,17 @@ class DPS310:
         self.mode = Mode.CONT_PRESTEMP
 
         # wait until we have at least one good measurement
-        self.wait_temperature_ready()
-        self.wait_pressure_ready()
 
-    # (https://github.com/Infineon/DPS310-Pressure-Sensor#temperature-measurement-issue)
+        while (self._temp_ready is False) or (self._pressure_ready is False):
-    # similar to DpsClass::correctTemp(void) from infineon's c++ library
+            sleep(0.001)
-    def _correct_temp(self):
-        """Correct temperature readings on ICs with a fuse bit problem"""
-        self._reg0e = 0xA5
-        self._reg0f = 0x96
-        self._reg62 = 0x02
-        self._reg0e = 0
-        self._reg0f = 0
 
-        # perform a temperature measurement
+    def _reset(self):
-        # the most recent temperature will be saved internally
+        """Perform a soft-reset on the sensor"""
-        # and used for compensation when calculating pressure
-        _unused = self._raw_temperature
-
-    def reset(self):
-        """Reset the sensor"""
         self._reset_register = 0x89
         # wait for hardware reset to finish
         sleep(0.010)
         while not self._sensor_ready:
             sleep(0.001)
-        self._correct_temp()
-        self._read_calibration()
-        # make sure we're using the temperature source used for calibration
-        self._temp_measurement_src_bit = self._calib_coeff_temp_src_bit
 
     @property
     def pressure(self):
@@ -314,51 +295,11 @@ class DPS310:
         """Returns true if there is a temperature reading ready"""
         return self._temp_ready
 
-    def wait_temperature_ready(self):
-        """Wait until a temperature measurement is available.
-
-        To avoid waiting indefinitely this function raises an
-        error if the sensor isn't configured for temperate measurements,
-        ie. ``Mode.ONE_TEMPERATURE``, ``Mode.CONT_TEMP`` or ``Mode.CONT_PRESTEMP``.
-        See the `Mode` documentation for details.
-        """
-        if (
-            self._mode_bits == Mode.IDLE
-            or self._mode_bits == Mode.ONE_PRESSURE
-            or self._mode_bits == Mode.CONT_PRESSURE
-        ):
-            raise RuntimeError(
-                "Sensor mode is set to idle or pressure measurement,\
-                    can't wait for a temperature measurement"
-            )
-        while self._temp_ready is False:
-            sleep(0.001)
-
     @property
     def pressure_ready(self):
         """Returns true if pressure readings are ready"""
         return self._pressure_ready
 
-    def wait_pressure_ready(self):
-        """Wait until a pressure measurement is available
-
-        To avoid waiting indefinitely this function raises an
-        error if the sensor isn't configured for pressure measurements,
-        ie.  ``Mode.ONE_PRESSURE``, ``Mode.CONT_PRESSURE`` or ``Mode.CONT_PRESTEMP``
-        See the `Mode` documentation for details.
-        """
-        if (
-            self._mode_bits == Mode.IDLE
-            or self._mode_bits == Mode.ONE_TEMPERATURE
-            or self._mode_bits == Mode.CONT_TEMP
-        ):
-            raise RuntimeError(
-                "Sensor mode is set to idle or temperature measurement,\
-                    can't wait for a pressure measurement"
-            )
-        while self._pressure_ready is False:
-            sleep(0.001)
-
     @property
     def mode(self):
         """The measurement mode. Must be a `Mode`. See the `Mode` documentation for details"""

examples/dps310_low_power_weather_station.py

@@ -1,34 +0,0 @@
-"""
-Configure the sensor for continuous measurement with rates,
-sampling counts and mode optmized for low power, as recommended
-in Infineon's datasheet:
-https://www.infineon.com/dgdl/Infineon-DPS310-DS-v01_00-EN.pdf
-"""
-
-# (disable pylint warnings for adafruit_dps310.{SampleCount,Rate,Mode}.*
-# as they are generated dynamically)
-# pylint: disable=no-member
-
-import time
-import board
-import busio
-import adafruit_dps310
-
-i2c = busio.I2C(board.SCL, board.SDA)
-
-dps310 = adafruit_dps310.DPS310(i2c)
-
-dps310.reset()
-dps310.pressure_oversample_count = adafruit_dps310.SampleCount.COUNT_2
-dps310.pressure_rate = adafruit_dps310.Rate.RATE_1_HZ
-dps310.temperature_oversample_count = adafruit_dps310.SampleCount.COUNT_16
-dps310.temperature_rate = adafruit_dps310.Rate.RATE_1_HZ
-dps310.mode = adafruit_dps310.Mode.CONT_PRESTEMP
-dps310.wait_temperature_ready()
-dps310.wait_pressure_ready()
-
-while True:
-    print("Temperature = %.2f *C" % dps310.temperature)
-    print("Pressure = %.2f hPa" % dps310.pressure)
-    print("")
-    time.sleep(10.0)