/**
 * \file
 *
 * \brief SAM Direct Memory Access Controller Driver
 *
 * Copyright (C) 2014-2015 Atmel Corporation. All rights reserved.
 *
 * \asf_license_start
 *
 * \page License
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 *
 * 3. The name of Atmel may not be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * 4. This software may only be redistributed and used in connection with an
 *    Atmel microcontroller product.
 *
 * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 * \asf_license_stop
 *
 */
/*
 * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
 */
#ifndef DMA_H_INCLUDED
#define DMA_H_INCLUDED

// THIS IS A PARED-DOWN VERSION OF DMA.H FROM ATMEL ASFCORE 3.
// Please keep original copyright and license intact!

#ifdef __cplusplus
extern "C" {
#endif

extern DmacDescriptor // 128 bit alignment
  _descriptor[DMAC_CH_NUM],
  _writeback[DMAC_CH_NUM];

#if (SAML21) || (SAML22) || (SAMC20) || (SAMC21) || defined(__DOXYGEN__) || defined(__SAMD51__)
#define FEATURE_DMA_CHANNEL_STANDBY
#endif

enum dma_transfer_trigger_action{
#ifdef __SAMD51__
	// SAMD51 has a 'burst' transfer which can be set to one
	// beat to accomplish same idea as SAMD21's 'beat' transfer.
	// Trigger name is ACTON_BEAT for backward compatibility.
	DMA_TRIGGER_ACTON_BLOCK       = DMAC_CHCTRLA_TRIGACT_BLOCK_Val,
	DMA_TRIGGER_ACTON_BEAT        = DMAC_CHCTRLA_TRIGACT_BURST_Val,
	DMA_TRIGGER_ACTON_TRANSACTION = DMAC_CHCTRLA_TRIGACT_TRANSACTION_Val,
#else
	DMA_TRIGGER_ACTON_BLOCK       = DMAC_CHCTRLB_TRIGACT_BLOCK_Val,
	DMA_TRIGGER_ACTON_BEAT        = DMAC_CHCTRLB_TRIGACT_BEAT_Val,
	DMA_TRIGGER_ACTON_TRANSACTION = DMAC_CHCTRLB_TRIGACT_TRANSACTION_Val,
#endif
};

enum dma_callback_type {
	// First item here is for any transfer errors. A transfer error is
	// flagged if a bus error is detected during an AHB access or when
	// the DMAC fetches an invalid descriptor
	DMA_CALLBACK_TRANSFER_ERROR,
	DMA_CALLBACK_TRANSFER_DONE,
	DMA_CALLBACK_CHANNEL_SUSPEND,
	DMA_CALLBACK_N, // Number of available callbacks
};

enum dma_beat_size {
	DMA_BEAT_SIZE_BYTE = 0, // 8-bit
	DMA_BEAT_SIZE_HWORD,    // 16-bit
	DMA_BEAT_SIZE_WORD,     // 32-bit
};

enum dma_event_output_selection {
	DMA_EVENT_OUTPUT_DISABLE = 0, // Disable event generation
	DMA_EVENT_OUTPUT_BLOCK,       // Event strobe when block xfer complete
	DMA_EVENT_OUTPUT_RESERVED,
	DMA_EVENT_OUTPUT_BEAT,        // Event strobe when beat xfer complete
};

enum dma_block_action {
	DMA_BLOCK_ACTION_NOACT = 0,
	// Channel in normal operation and sets transfer complete interrupt
	// flag after block transfer
	DMA_BLOCK_ACTION_INT,
	// Trigger channel suspend after block transfer and sets channel
	// suspend interrupt flag once the channel is suspended
	DMA_BLOCK_ACTION_SUSPEND,
	// Sets transfer complete interrupt flag after a block transfer and
	// trigger channel suspend. The channel suspend interrupt flag will
	// be set once the channel is suspended.
	DMA_BLOCK_ACTION_BOTH,
};

// DMA step selection. This bit determines whether the step size setting
// is applied to source or destination address.
enum dma_step_selection {
	DMA_STEPSEL_DST = 0,
	DMA_STEPSEL_SRC,
};

// Address increment step size. These bits select the address increment step
// size. The setting apply to source or destination address, depending on
// STEPSEL setting.
enum dma_address_increment_stepsize {
	DMA_ADDRESS_INCREMENT_STEP_SIZE_1 = 0, // beat size * 1
	DMA_ADDRESS_INCREMENT_STEP_SIZE_2,     // beat size * 2
	DMA_ADDRESS_INCREMENT_STEP_SIZE_4,     // beat size * 4
	DMA_ADDRESS_INCREMENT_STEP_SIZE_8,     // etc...
	DMA_ADDRESS_INCREMENT_STEP_SIZE_16,
	DMA_ADDRESS_INCREMENT_STEP_SIZE_32,
	DMA_ADDRESS_INCREMENT_STEP_SIZE_64,
	DMA_ADDRESS_INCREMENT_STEP_SIZE_128,
};

#ifdef __cplusplus
}
#endif

#endif // DMA_H_INCLUDED