Although the rpi_pico can already build and run with the zephyr port, this
configuration improves it in a number of ways:
- Use the USB CDC ACM as the REPL, rather than just a UART.
- Enable I2C and SPI, and add I2C1.
- Enable a filesystem, which matches exactly the rp2 port's RPI_PICO
configuration. So switching between zephyr and rp2 is possible and will
retain the filesystem.
- Make the MicroPython GC heap make the most use of the available RAM.
Signed-off-by: Damien George <damien@micropython.org>
Bluetooth works well now on this board, so enable all supported features.
Also increase the MicroPython GC heap size to make use of the available
RAM.
Unfortunately the filesystem does not match the stm32 port's NUCLEO_WB55
configuration. That's not possible to do because stm32 uses a 512 byte
flash erase size, while zephyr uses 4096 bytes. But at least here in
zephyr there's now a sizable and usable filesystem.
Signed-off-by: Damien George <damien@micropython.org>
Most boards enable the UART console because it's needed for USB (where USB
CDC creates a virtual UART), and for ctrl-C to work.
The `prj_minimal.conf` settings still use CONSOLE_SUBSYS.
Fixes issue #17608.
Signed-off-by: Damien George <damien@micropython.org>
Since MicroPython supports Zephyr v4.0.0, no need for overlay to enable
PWM. It is enabled by default for a while now.
Signed-off-by: Ayush Singh <ayush@beagleboard.org>
This commit adds the required functionality for a peripheral to create
services at runtime, using `BLE.register_services()`.
The feature is enabled on the nrf52840dk_nrf52840 board.
Note that the `CONFIG_BT_GATT_ENFORCE_SUBSCRIPTION=n` option must be used
so that BLE notifications/indications can be sent even if not subscribed.
Signed-off-by: danicampora <danicampora@gmail.com>
Add support for the nrf5340dk. This DK has a MX25R64 8mb external QSPI
flash chip.
Compile using:
$ west build -b nrf5340dk/nrf5340/cpuapp
Signed-off-by: Patrick Joy <patrick@thinktransit.com.au>
Enables the ability to use frozen modules in the zephyr port.
Enabled by adding `CONFIG_MICROPY_FROZEN_MODULES` to the board
configuration file. Manually set manifest path with
`CONFIG_MICROPY_FROZEN_MANIFEST`.
Signed-off-by: Vdragon <mail@massdriver.space>
This commit implements the `_thread` module on the zephyr port.
Due to the fact that we are still using a rather old version of Zephyr,
`CONFIG_DYNAMIC_THREAD` is not available and therefore the stack for
threads cannot be allocated dynamically, only at compile time. So for the
time being and for the purpose of this commit, a maximum of 4 Zephyr
threads (besides the main thread) can be created. Once we manage to update
to the latest version of Zephyr this won't be a problem anymore.
Configuration for the nrf52840dk is added as part of this change, because
this board was used to test the threading support.
The Zephyr option `CONFIG_THREAD_CUSTOM_DATA` is used to enable threading
on a per board basis. The `thread.conf` file is added as a convenient way
to enable threading.
Signed-off-by: danicampora <danicampora@gmail.com>
CONFIG_USB was removed in Zephyr v2.7.0 after some Kconfig rework that
made it sufficient to use CONFIG_USB_DEVICE_STACK only.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Adds support for hardware SPI to the zephyr port. Consistent with other
ports, such as rp2 and stm32, we only implement the SPI protocol functions
(init and transfer). Explicit sck/mosi/miso selection is not supported
and new SPI instances are initialized with default values.
Zephyr's Kconfig symbols and defaults for SDHC/SDMMC disk drivers and
the disk access subsystem were reworked between Zephyr v2.5.0 and
v2.6.0. Update MicroPython accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This board does not work with CONFIG_NETWORKING enabled. And
CONFIG_CONSOLE_SUBSYS is enabled so that ctrl-C works.
Signed-off-by: Damien George <damien@micropython.org>
The zephyr build system supports merging application-level board
configurations, so there is no need to reproduce this functionality in
MicroPython.
If CONF_FILE is not explicitly set, then the zephyr build system looks for
prj.conf in the application directory. Therefore we rename the MicroPython
prj_base.conf to prj.conf.
Furthermore, if the zephyr build system finds boards/$(BOARD).conf in the
application directory, it merges that configuration with prj.conf.
Therefore we rename all the MicroPython board .conf files and move them
into a boards/ directory.
The minimal configuration, prj_minimal.conf, is left in the application
directory because it is used as an explicitly set CONF_FILE in
make-minimal.
