Following the commit f98fde07b3, DT_REG_ADDR now expands with a 'U'
suffix as an unsigned value. However, for compatibility with IS_EQ,
a raw value without any suffix is required. Therefore, this update is
necessary.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
This commit deals with fixing various issues that prevents
the device from being built. In specific:
1. Fix default timing macro definitions to build with
an MSPI controller, other than AMBIG.
Add macro definition for MSPI_PORT.
2. Timing settings should be applied only when MSPI_TIMING
is defined. Otherwise, the APS6404 initialization routine
will fail with -EIO.
3. Similarly, use MSPI_XIP and MSPI_SCRAMBLE to apply XIP
and SCRAMBLE device settings, respectively (optimization).
4. MEMC_INIT_PRIORITY is assigned higher priority than
MSPI_INIT_PRIORITY which results in compiler error as
APS6404 device initialization depends on its underlying
MSPI bus controller.
5. The 'acquire' subroutine should be compiled when PM_DEVICE
is used (suppress compiler warning).
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
This Kconfig has wrongly been added to defconfig files. It is not the
right place for it. It has never been the right place for it. Drivers
that need it should select the symbol in their Kconfig entries. Drop
PINCTL from Kconfig.defconfig and add proper select at Kconfig.sam*.
Fixes#78619
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Some instances of the FLEXSPI IP permit limiting AHB bus access so that
no memory access requests will straddle a page boundary. Add a property
to manage this setting.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
is66wvq8m4 PSRAM always requires the address to be left shifted by
5 bits, regardless of which FLEXSPI port it is on. Fix the addressShift
assignment to be unconditional
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The ADDRSHIFT bit simply left shifts the address written to IPCR0[SFAR],
(or the address used for AHB access), by 5 bits before sending it to the
attached memory. This bit does not have an effect on the base address
used to access the flash/psram device.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Select PINCTRL subsystem by drivers which require it.
Prevent the need from enabling this symbol at board or soc level.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Some flash/memc drivers like flexspi will want to default the
value of the log level to off to avoid RWW hazard while XIP,
to do this, the logging template must be sourced after the driver
kconfig files so that the default value from the driver is able
to be checked, since logging template introduces an unconditional
default otherwise.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add missing braces to comply with MISRA C:2012 Rule 15.6 and
also following Zephyr's style guideline.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
REG_X_BASEADDR will be removed from all hal files.
This forces the use of the peripheral base address
Define MSPI_PORT macro for chip drivers
Signed-off-by: Richard Wheatley <richard.wheatley@ambiq.com>
This commit fixes a bug with the declaration of the Kconfig option
MEMC_STM32.
The option is defined in two files:
- `drivers/memc/Kconfig.stm32`, wich depends on
- `MEMC`
- `DT_HAS_ST_STM32_FMC_ENABLED`
-`soc/st/stm32/Kconfig.defconfig`, wich depends on
- `MEMC`
- `SOC_FAMILY_STM32`
So, if you have `CONFIG_MEMC=y` in your Kconfig options and you are on a
STM32 SoC, `CONFIG_MEMC_STM32` will be enabled, even if there is no
STM32 FMC enabled.
This Kconfig option causes the driver for the STM32 FMC to be compiled,
regardless of the presence of an enabled node for the FMC.
However, the driver fails to compile if there is no FMC node in the
devicetree. So, if you compile a project with `CONFIG_MEMC=y` on a board
with an STM32 SoC and no enabled FMC, the build will fail.
This commit deletes the Kconfig declaration in the `Kconfig.defconfig`,
as it isn't useful and is the one provoking the bug.
It also add in the `Kconfig.stm32` the compatible `st,stm32h7-fmc`, wich
use the same driver and so need to be enabled by the same Kconfig
option.
Signed-off-by: Miguel Gazquez <miguel.gazquez@bootlin.com>
Removed PM device runtime support from drivers in PD_SYS domain.
Update the rest device drivers to call pm_device_runtime_get/put()
functions when CONFIG_PM_DEVICE_RUNTIME is enabled.
Signed-off-by: Ioannis Damigos <ioannis.damigos.uj@renesas.com>
The APS6404L psram is a quad SDR SPI device that runs up to 100MHz.
It can provide 8MB of external RAM for SoCs that supports XIP feature.
The device driver uses MSPI bus API and could be used across
different controllers that implement the MSPI bus API.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
Add support for the memory controller by utilizing QSPIC2. The latter is
capable to drive both NOR and PSRAM memory devices. For this to work,
the RAM driving mode is enabled.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Do not reset the FLEXSPI during init, as this will crash the chip if we
are running the MEMC driver in XIP mode.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for initializing the FLEXSPI when using a flash attached to
the FLEXSPI for XIP. This option is guarded behind a Kconfig, as
enabling it is dangerous and requires special care be taken by the user
to ensure that the configuration of pins and FLEXSPI settings will not
break support for reading the attached flash, as this will break XIP
support.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use custom initialization priority for FLEXSPI MEMC driver. This may be
needed when the MEMC driver must initialize before a flash driver, and
before another MEMC driver (for an attached device, like PSRAM)
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
When multiple devices are used, the FLEXSPI will place their address
spaces sequentially (based on the chip select port used). Additionally,
each device must use different sections of the FLEXSPI LUT table.
Fix the following calculation issues with multi-device usage:
- correct calculation of LUT sequence indices for AHB commands
- correctly add address and sequence offset when submitting FLEXSPI IP
transfer
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update documentation for flash_config memc function, to correctly
reflect usage of the "lut_count" parameter
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add driver for IS66WVQ8M4 PSRAM, using the MCUX FlexSPI interface to
write data to the PSRAM device.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Some instances of the FlexSPI IP support a different clock source being
used for port B of the FlexSPI instance. Add a devicetree property and
driver support to enable configuring this property of the hardware.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
From IMXRT1170RM.pdf, iomuxc_gpr->GPR17 is
used to configure FlexRAM bank 0~7.
iomuxc_gpr->GPR18 is used to configure
FlexRAM bank 8~15.
Set low 2 bytes to iomuxc_gpr->GPR17.
Set high 2 bytes to iomuxc_gpr->GPR18.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Support SFDP probe in flexspi nor driver. This probe will allow the
flash driver to dynamically configure quad spi flashes for 1-4-4 mode,
expanding the flash chips supported with this driver.
The following data is read from the SFDP header:
- quad enable method
- fast read command (1-4-4 is maximum supported)
Fixes#55379
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for reclocking the FlexSPI on NXP iMX RT10XX. This
functionality requires an SOC specific clock function to set
the clock rate, since the FlexSPI must be reset directly
before applying the new clock frequency.
Note that all clock constants are defined in this commit, since the
memc flexspi driver now depends on a clock node being present.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Get GPR base address using nodelabel as this will align for all the
current in tree platforms. Currently inst 0 of the compat gets wrong
node and base address on RT11xx.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
GPR17 calculation for configuration of RAM banks is incorrect,
bit shift should be 2 per idx, not 1, this is major bug that needs
correcting, currently all RT boards are affected with wrong
configuration.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
One of the ARM architure files, defined since long ago
CONCAT having the exact same purpose as Zephyr's _CONCAT.
Unfortunately this header is included almost always
and the macro defined in all ARM based platforms,
which seems to have lead to many uses of this macro
instead of _CONCAT.
Fix it by using _CONCAT instead.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Update interface of memc flexspi driver to better handle multiple
devices. Previously, using multiple devices on one FlexSPI bus would
require the user to configure each device to install its command table
(referred to as a LUT table by the driver) at an offset, so that it did
not overlap with other devices on the bus.
This commit changes the interface of the memc flexspi driver to instead
configure the LUT and flash device in one call. This allows the memc
driver to record the port each LUT sequence is used with, so that
future FlexSPI transfer requests can have their LUT offsets adjusted
based on the target port (which will correspond to a target device)
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Check XIP state based on the value of CONFIG_FLASH_BASE_ADDRESS. This
check should be more reliable than the SOC based method currently
used.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The NXP S32 QSPI controller acts as an interface to up to two serial
flash memory devices, each with up to eight bidirectional data lines,
depending on the platform. It is based on a LUT enginee to interface
through commands with different memory types including flash NOR and
Hyperram.
This patch adds support for the QSPI in S32K344 which supports a single
memory device (side A) with up to four bidirectional data lines and SDR
only. Nevertheless, the memory controller is implemented flexible enough
to be extended to support more feature-rich QSPI blocks.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add a function to update the flexspi bus clock. This is
needed when write operations are done to the hyperflash.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
The MCUX platform always uses pinctrl, there's no need to keep extra
macrology around pinctrl. Also updated driver's Kconfig options to
`select PINCTRL` (note that some already did).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
HAL API changes in ethernet and pwm
SoC RT595 power management code change
west.yml update
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update flexspi driver init priority to be the
memc driver init priority. This fixes a bug where
the flexspi flash drivers on i.MX RT platforms were
being initialized before the flexspi memc driver.
Since those flash drivers depend on the flexspi
spi bus controller being initialized, the flash drivers
would fail to initialize and cause runtime failures.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Allow configuration of AHB RX buffer allocation. This allows sections
of the AHB RX buffer to be reserved for specific masters, which can
enhance performance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update usage of zephyr_code_relocate to follow new API. The old method
of relocating a file was the following directive:
zephyr_code_relocate(file location)
The new API for zephyr_code_relocate uses the following directive:
zephyr_code_relocate(FILES file LOCATION location)
update in tree usage to follow this model. Also, update the NXP HAL SHA,
as NXP's HAL uses this macro as well.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
