Change the property names in the bindings and overlay
to use hyphens(-) for separation instead of underscores(_).
Signed-off-by: James Roy <rruuaanng@outlook.com>
The TMP435 is a remote temperature sensor monitor
with a built-in local temperature sensor.
Signed-off-by: Jaakko Rautiainen <jaakko.rautiainen@bittium.com>
The MAX22017 is a two-channel industrial-grade software-configurable
analog output device that can be used in either voltage or current output
mode.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
- Remove PLCA paramaters from lan865x SPI device description.
- Add MDIO and internal PHY device description along with PLCA
parameters in the PHY node.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Add wsen_pdus_25131308XXXXX driver with
the corrected name and compatibility with
the hal update as well as added new features..
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Use a string for the xfr-min-bits property over an integer value, as this
significantly improves the readability of the MIPI DBI SPI device binding.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Fixes issue introduced in #76460
The previous code attempted to detect whether TMAG5273 or TMAG3001 was
connected based on DEVICE ID register. This doesn't work as the bits that
denote the version on one part are undefined on the other part, and cannot
be relied on to be zero.
This commit adds a TMAG3001 compatible which (for now) is just derived from
the TMAG5273 compatible. This allows TMAG3001 to be specified directly in
the DT. The driver code is updated to support both compatibles.
Signed-off-by: Yiding Jia <yiding.jia@gmail.com>
The it8801 template is helpful but in the current state it does not
allow changing the device address as that is in the template itself. Fix
that by moving the template content down a level in the hierarchy, so
that it extends the mfd device itself rather than than instantiate it,
then the base instance can have any address, now the only limitation is
that only one instance is possible, but that is probably alright for
now.
Alternatives would be to use a define for the address, or even a
template per address, but this feels like a better compromise for now.
This may also use
https://github.com/zephyrproject-rtos/zephyr/pull/82825 in the future if
that ever becomes a thing.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Adds the counter property to the tmc2209 node to ensure counter dependant
step-dir code is build by CI.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
The LIS2DUXS12 is a smart, digital, 3-axis linear accelerometer whose
MEMS and ASIC have been expressly designed to combine the lowest current
consumption possible with features such as always-on antialiasing
filtering, a finite state machine (FSM) and machine learning core (MLC)
with adaptive self-configuration (ASC), and an analog hub / Qvar sensing
channel.
(https://www.st.com/en/mems-and-sensors/lis2duxs12.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
- rename enable-gpios to en-gpios in adi,tmc2209
- place en-gpios in common stepper-controller.yaml
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Modify the board file when using gpio, input and pwm drivers dts
configuration example for it8801.
test: west build -p always -b it82xx2_evb tests/drivers/build_all/gpio
west build -p always -b it82xx2_evb tests/drivers/build_all/input
west build -p always -b it82xx2_evb tests/drivers/build_all/pwm
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Adds the drv8424 stepper driver to the build_all/stepper test and the
stepper_api test. The later test is also modified to ensure compatibility.
Signed-off-by: Jan Behrens <jan.behrens@navimatix.de>
ADS131M02 is Texas Instruments 2-channel, 24-Bit differential
input ADC which support wide range datarate.
Driver add support for adc read, channel configure, adc sampling
mode configuration and power management.
[1]. https://www.ti.com/lit/ds/symlink/ads131m02.pdf
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
Add max22190 gpio driver with input functionality, since device
support only input without output.
Implemented diagnostic functionality for all 8 channels
which include various check to over/under voltage and wire break.
Filtering configuration is done from devicetree on per channel
bases and is configured on chip start.
In case some fault condition occure FAULT pin drive LOW which
prop to FAULT registers to be read. Data is stored in data structure
for furter analizes and ERR message is printed in console.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
Add device definitions in dt to test drivers that handle
multiple "compatible"s by a single driver.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add device definitions in dt to test drivers that handle
multiple "compatible"s by a single driver.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Adds driver support for the charge enable (ce) gpio. This GPIO is
optional and if no GPIO is allocated the pin is assumed to be asserted.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Add a driver for the Nintendo Nunchuk, accessed through the I2C bus.
This driver only supports the joystick and the buttons, not the
accelerometer.
Signed-off-by: Miguel Gazquez <miguel.gazquez@bootlin.com>
Add device definitions in dt to test drivers that handle
multiple "compatible"s by a single driver.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
for the brevity renaming direction_gpios to dir_gpios since STEP/DIR
interface is quite an established term in context of stepper controllers.
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Add configuration with 16-bit transfer to C4 by the new `xfr-min-bits`
property. Such a setup generally only allows `write-only` access.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Add a new implementation of a test pattern generator, with the same
architecture as real drivers: split receiver core and
I2C-controlled sub-device, with changes of video format in
"zephyr,emul-imager" leads to different data produced by
"zephyr,emul-rx".
Signed-off-by: Josuah Demangeon <me@josuah.net>
Add watchdog driver for npm2100 pmic.
This pmic has one timer that can be used for multiple functions,
including a watchdog that can reset or power-cycle connected devices.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add sensor driver for npm2100 pmic.
This pmic performs measurements of battery voltage, regulator voltage
and die temperature.
Configurable pmic attributes are also organized under this driver.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add regulator driver for npm2100 pmic.
This pmic has one boost and one ldo regulator.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Convert them to native YAML lists. Support for space-separated
lists was deprecated in Twister a long time ago.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add support for setting the sample frequency via `attr_set` and the
output data rate from device tree source.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add build tests for the IT8801 MFD drivers, including GPIO,
Input and PWM functionalities.
GPIO, Input test: west build -p always -b native_sim
PWM test: west build -p always -b it82xx2_evb
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
