The DHT[11/22] sensor driver fails to read data due to an extra
"gpio_pin_set_dt" that is occurs prior to waiting for the sensor active
response. This leads to consistent failed reads on esp32 (devkitc,
wrover). After removing this line reads are consistently successful.
Signed-off-by: Omar Naffaa <omarnaffaa.on@gmail.com>
When all sectors have non-zero data, NVS would fail to init.
Add recovery path option to erase the all sectors and reinitialize.
This could occur due to non-empty sectors, or corrupted data.
Signed-off-by: Cory Andrew Mayer <corymayer@meta.com>
add test for reconfigure, release, suspend, abort and disconnect.
app_config_req and app_reconfig_req always accept the req,
so don't need to handle reject case.
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Implement the bt_a2dp_stream_reconfig: Modify reconfig_req callback to
pass codec_cfg to application. Remove reconfig_rsp callback,
config_rsp is used. Remove reconfigured callback,
configured callback is used.
move the status to common struct bt_avdtp_req,
use same bt_avdtp_ctrl_params to process control-like avdtp
cmds (start, open etc), use the same a2dp_ctrl_ind to process
control-like cmds (start, open etc), use the same
bt_a2dp_ctrl_cb to process control-like cmds (start, open etc),
use the same bt_avdtp_ctrl to process control-like cmds
(start, open etc), optimize getting a2dp conn by index,
use sem to replace mutex and optimze the lock codes to be
based on context/instance.
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
We should also trigger this workflow on changes to the
module integration files.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This results in a smaller binary with CONFIG_XIP=n as these NOLOAD
sections can be excluded.
bss/noinit have been included in CONFIG_XIP=n binaries by default since
c107827bb7. This also occurs if using
iterable sections or adding code/data to ITCM/DTCM sections.
Moving bss/noinit to the end of the linker file should ensure they are
always excluded
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
Instead of unconditionally erasing the whole target, add
support for using the common --erase flag.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Revert to my old username on west and drop my long-inactive LED strip
involvement.
(I'm intentionally not adding myself back to the devicetree
collaborators list -- I'm not able to help out there at this time.)
Signed-off-by: Martí Bolívar <marti.bolivar@oss.qualcomm.com>
This reverts commit b33b3b17f7, turns out
it's causing issues in CI all over the place, the condition needs more
thinking.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The commit adds Kconfig option CONFIG_STREAM_FLASH_POST_WRITE_CALLBACK
that allows to turn off support for callback invoked after data
is written to storage device.
If the feature is not used disabling it allows to save some storage.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Make sure CI can properly run on bootloader module by pulling
the mcuboot version that has correct names for the mimxrt1050/60
platforms.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Fast SPIM instances (SPIM120 and SPIM121) for correct operation require
the highest frequency from the global HSFLL. This commit adds needed
clock controller requests to the driver. When the runtime device power
management is enabled, the frequency is requested as long as the SPIM
is resumed, otherwise it is requested for the duration of transfers.
This commit also adds a missing call to `pm_device_runtime_put()` when
SPIM reconfiguration fails.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fast SPIM instances in nRF54H20 (SPIM120 and SPIM121) are driven by
the global HSFLL (HSFLL120). Add `clocks` property in these nodes
to reflect this.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is a follow-up to commit fe0e2dbc60.
If `nrf_clock_control_request_sync()` ends up with a timeout, before
returning it must cancel the request that was not fulfilled on time.
Otherwise, the request may actually finish successfully a bit later,
but the caller will not be aware that the clock needs to be released
(since the call resulted in an error). And actually even more serious
problem is that because the `req` structure is placed on stack, after
the function returns, the contents of this structure will be probably
overwritten with some other data, so if the request finishes at that
point, an attempt to execute the callback function pointed by this
structure will most likely cause a crash.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
coverity complains of a missing break statement in SENSOR_CHAN_ALL case
this is fixed by adding __attribute__((fallthrough))
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Calling `net_buf_reserve` removed any previous reservation, which
includes the reservation by hci_ipc to hold the H4 type byte. This
resulted in a out-of-bounds net_buf_push in hci_ipc.
This commit also enables asserts in hci_ipc in the audio bsim test,
which reveal the out-of-bounds write.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
The LoRa driver does not allow to pass void* user_data to callback in
lora_recv_async function. This leads to complex way of using the API. This
commit fixes the issue and adds the field to the function and to the
callback.
Signed-off-by: Aleksander Dejewski <aleksander.dejewski@gmail.com>
Info in the release notes about changes to the board
identifier of the mimxrt1060_evk and mimxrt1050_evk.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Convert qspi and hyperflash to variants instead of revisions by popular
demand.
And convert evkb into a revision instead of a different board.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Update hal_renesas rev to add support for these features:
- SDRAM support on EK-RA8D1
- LCD controller
- MIPI DSI
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
NXP FlexTimer Module is a configurable timer peripheral hence it should
be located under bindings/timer.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Rename "nxp,kinetis-ftm-pwm" compatible to "nxp,ftm-pwm" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
