This commit adds the clock driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the pinctrl driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the dtsi and bindings for the WCH CH32V003 which is a
32-bit general-purpose RISC-V MCU.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
- Add SPI driver support for RA
- RA2A1 not support slave select keeping level so disable it
in Kconfig
Signed-off-by: Tri Nguyen <tri.nguyen.wj@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Use a string for the mipi-mode property over an integer value, as this
significantly improves the readability of the MIPI DBI device binding.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The NXP LCDIC peripheral contains two internal timers, with configurable
periods. These times are used to determine delays within the peripheral,
such as the reset and tearing enable signal delays. Allow these periods
to be set within the devicetree for the peripheral.
Raise the period where required for display drivers that need a value
other than the reset setting
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Extend tca954x (tca9546a, tca9548a) driver to support tca9544a i2c MUX.
(different bitmask and flag for enable bit in register)
Signed-off-by: Florian Weber <Florian.Weber@live.de>
The NXP PORT pinmuxing peripheral is reused across the MCX, S32, and
Kinetis lines. Rename the compatible from the family-specific
nxp,kinetis-pinctrl to a more generic nxp,port-pinctrl to reflect the
actual name for the IP block used within reference manuals.
Update the NXP HAL revision to include a change to use the new Kconfig
name for the PORT pinctrl driver
Update the MAINTAINERS.yml path, as there are no longer any NXP drivers
matching the string "drivers/*/*kinetis*
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
* Replace copies of fixed-partitions nodes in related boards by
referencing the apropriate partition table from the available list.
* For better reference the `partitions_*.dtsi` file has boot offset,
purpose and the flash size encoded in the file name. Default flash size
is considered to be 4MB.
* Added the flash size node for the boards which are not based on the
module.
* Removed flash size registry from the esp32.*common.dtsi
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Split and fix the total SRAM size for STM32L4Px/L4Qx/L4Rx/L4Sx
device. Those MCUs with up to 640 Kbytes SRAM:
This is 640KB for the STM32L4Rxxx and STM32L4Sxxx devices :
• 192 Kbytes SRAM1 + 64 Kbytes SRAM2 + 384 Kbytes SRAM3
This is 320KB for the STM32L4P5xx and STM32L4Q5xx devices :
• 128 Kbytes SRAM1 + 64 Kbytes SRAM2 + 128 Kbytes SRAM3
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Split and fix the total SRAM size for STM32L47x/L48x/L49x/L4Ax
device. Those MCUs with up to 320 Kbytes SRAM:
• 96 Kbytes SRAM1 and 32 Kbyte SRAM2 on STM32L47x/L48x.
• 256 Kbyte SRAM1 and 64 Kbyte SRAM2 on STM32L49x/L4Ax
The sram0 node at address 0x20000000 and sram1 at address 0x10000000
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace the DT_INST_PROP_OR statements with defaults
in the devicetree binding of the iCE40.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
These two new ICs are variants of the nRF54L15 with different memory
sizes:
- nRF54L05: 500KB RRAM, 96KB RAM
- nRF54L10: 1022KB RRAM, 192KB RAM
- nRF54L15: 1524KB RRAM, 256KB RAM
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Removing direct #define usage in the DTSI file and converting these
definitions to use a dt-bindings header instead.
Relocates the RPI_PICO_DEFAULT_IRQ_PRIORITY definition to a DTSI file and
introduces an override.dtsi file. The override file is used when no other
override file is present, allowing for better flexibility and compliance
with Zephyr’s DTS structure.
Fixes: #79719
Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io>
Add `hifive_unmatched//s7` (earlier selected by default, using
`hifive_unmatched`) and `hifive_unmatched//u74` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Add `hifive_unleashed//e51` (earlier selected by default, using
`hifive_unleashed`) and `hifive_unleashed//u54` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Remove the renesas,ra-clock-generation-circuit driver, which is no longer
needed after migrating to the FSP-based implementation.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Remove the renesas,ra-pinctrl driver, which is no longer
needed after migrating to the FSP-based implementation.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add a common part for AMD board ACP_6_0_ADSP.
Add support for ACP_6_0_ADSP BOARD,
which represents ACP_6_0 soc.
This has a 1 Xtensa HiFi5 core, with 200-800MHz
1.75 MB HP SRAM / 512 KB IRAM/DRAM,
1 x SP (I2S, PCM), 1 x BT (I2S, PCM), 1 x HS(I2S, PCM), DMIC as
audio interfaces.
Signed-off-by: DineshKumar Kalva <DineshKumar.Kalva@amd.com>
A few bindings in the timer directory (for kernel timing sources) were
being used for counters (which can have alarms set, and have a distinct
API). Move these bindings to the counters directory.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added a binding description for the PPIB peripheral and added the device
tree nodes of the PPIB instances to the nRF54L15 and nRF54L20.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Convert the numerous revision compatibles to a DT property for the
revision called nxp,version (inspired from a linux DT property from
st called st,version on their DMA).
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This moves the SRAM definitions for STM32H56/7x chips up to the top
level since they are common to all of them.
Signed-off-by: Djordje Nedic <nedic.djordje2@gmail.com>
- stm32cO11/31 share the same spi peripheral
- include stm32_dma header to be able to configure
spi with dma config macros (STM32_DMA_PERIPH_TX,...)
in dts
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
The Xilinx AXI DMA Controller is commonly used in FPGA designs.
For example, it is a part of the 1G/2.5G AXI Ethernet subsystem.
This patch adds a driver for the Xilinx AXI DMA that supports
single MM2S and S2MM channels as well as the control and status
streams used by the AXI Ethernet subsystem.
Signed-off-by: Eric Ackermann <eric.ackermann@cispa.de>
This commit changes the way some x86 devicetree set the unit-address values
of memory nodes. Before the change, they were always set to `0`. After the
change, they are derived from the `DT_DRAM_BASE` macro to match the first
address specified by the reg property.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
some flashes support special opcodes
for 4-byte addressing, that can be used
without switching to 4-byte mode.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Alder Lake have at least 2 cores. Both boards using this SoC
(up_squared_pro_7000 and adl) are configured with
MP_MAX_NUM_CPUS=2, so dts should contain at least one more core.
Signed-off-by: Franciszek Pindel <fpindel@antmicro.com>
Implement a new stable-poll-period-ms property to specify a new (slower)
polling rate for when the matrix is stable.
The keyboard thread can eat up a surprisingly high amount of cpu cycles in
busy waiting if the specific hardware implementation happen to have a
particularly slow settle time, but high frequency polling is really only
needed when debouncing.
The new property allow slowing down the polling rate when the matrix is
stable (either key pressed but none to be debounced or idle in the case
of the gpio implementation with no interrupts), this allows reducing the
overall cpu time taken by the keyboard scanning thread when keys are
persistently pressed.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The it8xxx2_kbd KSO pins can be used as both keyboard scan and GPIO. By
default the keyboard scanning driver controls the output level of all
the KSO signals from 0 to (col-size - 1), meaning that any line in
between used as GPIO is going to have its output value overridden.
Add a kso-ignore-mask property to the keyboard scan driver to allow
specifiying extra pins that should not be controlled by the driver.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
