This reverts commit 184c0f9e9d.
Reducing system heap memory to 1024 caused runtime failures on some
platforms. This commit revert that change and return to the previous
size.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Moving from TinyCrypt to PSA Crypto API caused failures in the cpu_net
build due to RAM being overflowed. It turned out that 8192 bytes were
allocated for system heap memory, but Mbed TLS is the only user
of that memory (I found this though puncover) for AES purposes.
We reduce that to 1024 bytes because this should be enough for
this purpose.
Note: albeit this is also a standalone example, it's used extensively
in other samples/tests and babblesim, so a failure in building it
propagates in a lot of other failures.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Moving from TinyCrypt to PSA Crypto API caused an entropy source
to be always required, so this commit adds it in tests where
necessary.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
As part of the work of deprecating TinyCrypt in favor of
PSA crypto API, this commit fixes some kconfigs in order to
reduce the RAM footprint. In all involved samples RAM usage
was extremely high even with TinyCrypt (usually > 98%) and
of course it got overflowed once TinyCrypt got replaced by
Mbed TLS's PSA Crypto API.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This commit sets PSA Crypto API as the default library to perform
ECC-DH in HCI, replacing TinyCrypt (which is being deprecated).
Therefore the symbol BT_TINYCRYPT_ECC is renamed as BT_SEND_ECC_EMULATION.
References in samples/tests are also fixed.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
CONFIG_BT_USE_PSA_API was used in BT crypto/host modules to select
PSA crypto API over TinyCrypt (which was the default until now).
Since TinyCrypt is being deprecated and PSA crypto API is the new
standard library for crypto operations, CONFIG_BT_USE_PSA_API is
no more needed.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This uses Linux V4L2 controls as a reference to give names to the
CIDs. Apply the renaming down to the drivers that use them.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Unless the PHY is managed by LE power control, the CS procedure phy
needs to match the ACL phy.
Disabling the auto phy updates keeps the ACL on 1M.
The alternative would be to read the current phy by enabling
BT_USER_PHY_UPDATE but this still doesn't work if the phy is changed
after being read.
Signed-off-by: Olivier Lesage <olivier.lesage@nordicsemi.no>
Handling the security changed callback was missing, so it could happen
that the sample would try to read remote capabilities before the link
was encrypted, which is not allowed.
Signed-off-by: Olivier Lesage <olivier.lesage@nordicsemi.no>
Because the number of ACL RX buffers must be at least the number of
maximum connections plus one, increasing `CONFIG_BT_MAX_CONN` could
inadvertently lead to a build failure if the number of ACL RX buffers is
not also increased. This dependency may not be obvious to users.
To address this issue, this commit deprecates the
`CONFIG_BT_BUF_RX_COUNT` Kconfig symbol and computes the value in
`buf.h` using the new `BT_BUF_RX_COUNT` define. Note that the default
value and the minimum range value have been changed to 0 to "disable"
the option.
Additionally, to allow users to increase the number of ACL RX buffers,
this commit introduces the new `CONFIG_BT_BUF_RX_COUNT_EXTRA` Kconfig
symbol. The value of this symbol will be added to the computed value of
`BT_BUF_RX_COUNT`.
The configurations of tests and samples have been updated to reflect
these changes.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
The README files of these samples already indicate that they use the
Zephyr-specific HCI vendor extensions, but this may still not be clear
enough to some users, as evidenced in #81779. Add build asserts to make
sure the samples only build when Zephyr VS extensions have been enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
This sample requires Zephyr HCI vendor extension support by the used
Bluetooth controller. In the case of qemu this needs to be explicitly
indicated by enabling the corresponding devicetree property.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
add display type for fixtures to avoid conflcts
in NXP platform
1. add required regex for console harness.
2. add message after processing, ensure the flow is OK
3. reduce the test time in TEST mode
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Add collector parameter to metric creation macros so that it
is possible to bind the metric to collector already at built
time.
Also add optional user_data to metric macro calls so that user
can add optional data there. This will be used by network statistics
Prometheus support in subsequent commits.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Embed "struct prometheus_metric" to individual metric like
counter, gauge, histogram and summary. This way we avoid having
a separate base pointer in specific metrict struct. We also do
not need to search the specific metric from base metric as
we can simply use CONTAINER_OF() macro to get the base metric.
This embedding means that the counter, gauge, histogram and summary
metric define macros are changed as user does not need to create a
separate "struct prometheus_metric".
Convert the tests and sample to use the new macros.
Remove also the static from metric creation macros so that user
can decide whether it needs collector to be static or not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add a simple demonstration of the led_write_channels api on the lp5569
driver sample.
The demonstration simply turns on all of the channels with a single call to
led_write_channels. Then the same is done for turning off the channels.
Thus, it doesn't add much visually, but it shows the usage of the api.
Signed-off-by: Emil Dahl Juhl <emdj@bang-olufsen.dk>
Reducing the heap requirement for the hci_ipc sample from
8KiB to 4KiB. It has been tested in various configurations to
work with 2300, but 4KiB was used to provide some leeway for
future updates.
The heap requirement is not documented, and it is unclear why
values lower than 2300 (not exact number) won't boot, and should
be investigated further.
Memory has become a very scarce resource for especially the ISO
builds for the nRF5340, which is why this is getting reduced.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This PR adds arduino giga r1 overlay in the dac sample.
Arduino Giga R1 has a 3.5mm audio jack connected to the
dac.
Signed-off-by: Mario Paja <mariopaja@hotmail.com>
This is a follow-up to 21475774fc,
extending the number of tests and samples that use the new L05 and L10.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update the connection and advertising intervals of the
broadcast and connected ISO samples (including benchmark
samples) to work better with the selected SDU intervals
and the resulting ISO intervals.
For the ISO connected benchmark the order of CIG and ACl
has changed, so that we create the CIG before connecting
the ACL for the purpose of providing as much information
as possible to the controller.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add EAP-TLS, EAP-PEAP-MSCHAPv2, EAP-PEAP-GTC, EAP-TTLS-MSCHAPv2,
EAP-PEAP-TLS, EAP-TLS-SHA256 enterprise wpa2 and wpa3 suiteb
support for sap.
Signed-off-by: Rex Chen <rex.chen_1@nxp.com>
The required ISO Tx buffers have to match the Read Buffer
Size values, otherwise the difference in the value cause a
similar amount of buffers to be stalled in the IPC driver.
Use reduced HEAP size to make room for increase in RAM
usage.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add implementation for Extended Advertising Auxiliary PDUs
to use ticks slot window feature.
This will allow the periodic scheduling of AUX_ADV_IND PDUs
to drift upto 10 ms advertising delay minus the ticks_slot
time reservation of the AUX_ADV_IND PDU when overlapping
with other states/roles that cannot be moved around, to
avoid skipping them.
Having an active Extended Advertising simultaneously with
an ISO Synchronized Receiver or Connected ISO connection
will now have less ISO SDU loss when using 10 ms ISO
intervals.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Exclude stm32 platforms with accel0 or magn0
for running the samples/sensor for trigger
as their sensor driver does not have trigger set.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This addresses the following warning building with `CONFIG_64BIT=y`:
error: field precision specifier '.*' expects argument of type 'int',
but argument X has type 'size_t' {aka 'long unsigned int'}
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Move "bluetooth" tag and harness from the common section
of the smp_svr sample.yaml file to "bluetooth" specific test cases.
Signed-off-by: Andrej Butok <Andrey.Butok@nxp.com>
The nRF54L05 and nRF54L10 are identical to the nRF54L15 except for their
memory sizes. Add support for emulating those ICs on the nRF54L15DK.
This commit only adds support for the main application core. Support for
the FLPR core may be added later.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Change the select to a depends on for the Kconfig options
for HAS and HAS_CLIENT.
This is an effort to reduce the number of selects used by
LE Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Change the select of BT_PER_ADV_SYNC and BT_EXT_ADV to
depends on. This is an effort to reduce the use of
select for Kconfig options.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Modify ASCS and BAP Broadcast sink to depend on the PAC options
instead of selecting them.
Since Kconfig does not support "depends on X if Y",
a select for PAC_{SRC,SNK} is used depending on
ASCS_ASE_{SRC,SNK}.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The BAP Kconfigs option now depends on
BT_ISO_BROADCASTER instead of selecting it.
This is an effort to reduce the use of select in LE Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The BAP_BROADCAST_SOURCE Kconfig option now depends on
BT_ISO_BROADCASTER instead of selecting it.
This is an effort to reduce the use of select in LE Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Modify the Kconfig options to depend on the GATT
features rather than selecting them.
This is part of an effort to reduce the amount of
selects we use in LE Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
A valid device tree configuration is provided for the ADCs of the 8 input
channels and the sample adc_dt works out of the box. Obviously this is
not the only possible configuration but it provides a good template for
further customization without the need to lookup the ADC GPIOs and
connections in the schematics.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
This set of changes enables the RS485 hardware connected to usart3 and
provides some overlays that allow for easily running the modbus
rtu_client and rtu_server samples on Opta.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
This set of changes reorganize the ethernet configuration by removing the
use a regulator to enable the PHY: the correct GPIO pin is set in code
only if the network has been configured via CONFIG_NET_L2_ETHERNET.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
As long as MBEDTLS_ENTROPY_C is enabled, Mbed TLS needs to
poll some entropy source to gather data that will then be
processed by CTR/HMAC-DRBG modules. This means that in most
of the cases, once MBEDTLS_ENTROPY_C is enabled then also
MBEDTLS_ENTROPY_POLL_ZEPHYR needs to be enabled. This was
done manually until now, as the long list of samples/tests
demonstrate.
This commit solves this dependency by defaulting
MBEDTLS_ENTROPY_POLL_ZEPHYR to on as soon as
MBEDTLS_ENTROPY_C is set. As a consequence, all manual
enablement of MBEDTLS_ENTROPY_POLL_ZEPHYR in samples/tests
are removed.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
The main problem of MBEDTLS_PSA_CRYPTO_LEGACY_RNG is that it
brings in some legacy modules (entropy + ctr_drbg/hmac_drbg)
which means extra ROM/RAM footprint.
MBEDTLS_PSA_CRYPTO_EXTERNAL_RNG instead simply calls to the
CSPRNG which makes it definitely smaller.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Add `hifive_unmatched//s7` (earlier selected by default, using
`hifive_unmatched`) and `hifive_unmatched//u74` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Add `hifive_unleashed//e51` (earlier selected by default, using
`hifive_unleashed`) and `hifive_unleashed//u54` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Add possibility to retrieve VBUS status of the nPM1300 charger through
its sensor APIs. Updated shields/npm1300_ek sample to use the new API.
Signed-off-by: Sergei Ovchinnikov <sergei.ovchinnikov@nordicsemi.no>
Add a function similar to sample_usbd_init_device(), but one that does
not initialize the device. It allows the application to set additional
features, such as additional descriptors.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The nrfx_gppi module is an abstraction over nrfx_ppi and nrfx_dppi
drivers. It now has a Kconfig option that is separate from nrfx_dppi and
by default it enables all PPI/DPPI instances, if available.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
ARGB8888 values all had alpha '0x00' (=transparent).
Changed them to '0xFF' and added a transparency test patch in the middle
of the screen.
Signed-off-by: Martin Stumpf <finomnis@gmail.com>
`lv_task_handler()` returns a `uint32_t`, but `k_msleep` takes a
`int32_t`.
If no timer exists, `lv_task_handler()` returns `UINT32_MAX` to indicate
that we should wait forever. However, this gets auto-cast to `-1`,
indicating to `k_msleep` to not wait at all, creating a busy loop.
Hence, a clamping to `[0, INT32_MAX]` is required.
Signed-off-by: Martin Stumpf <finomnis@gmail.com>
Adds a sample that renders the simple `hello world` LVGL demo
with a transparent background, to demonstrate ARGB8888 framebuffer
capabilities.
Signed-off-by: Martin Stumpf <finomnis@gmail.com>
CONFIG_ENTROPY_DEVICE_RANDOM_GENERATOR is on
by default, if the device supports that, so there is no need
to enable it explicit.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
use auto init for networking, dhcp and sntp.
This simplifys the code of this sample by using the
auto init feature of the networking stack.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Obviously, everyone knows that there are 8 bits per byte, so
there isn't a lot of magic happening, per se, but it's also
helpful to clearly denote where the magic number 8 is referring
to the number of bits in a byte.
Occasionally, 8 will refer to a field size or offset in a
structure, MMR, or word. Occasionally, the number 8 will refer
to the number of bytes in a 64-bit value (which should probably
be replaced with `sizeof(uint64_t)`).
For converting bits to bytes, or vice-versa, let's use
`BITS_PER_BYTE` for clarity (or other appropriate `BITS_PER_*`
macros).
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
rpi_pico.conf only adds CONFIG_ADC=y which already exists in the
prj.conf so it's redundant and can be removed.
Signed-off-by: Yishai Jaffe <yishai1999@gmail.com>
Fixes: #78010
This commit adds the "Gateway Advertisement and Discovery" process
to the MQTT-SN Publisher Sample application.
Signed-off-by: Kenneth Witham <kennywitham4@gmail.com>
These samples demonstrate how to use the bluetooth 6.0 channel
sounding APIs. A basic distance estimation algorithm is included.
Signed-off-by: Olivier Lesage <olivier.lesage@nordicsemi.no>
Gives an example where the timeout value is 15seconds,
the prescaler of 8 can let the LPTIM count from 0 to 16 seconds
with LSE
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The sample had a few off-by-ones in the code, which caused access
to invalid data.
Fixed by setting the right buffer sizes and the right AD length
fields.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add conversion macros from milliseconds to various units.
The purpose of these macros is to make it more clear/easier
for users to set and read values using milliseconds rather
than the various BT units which may be in 0.625, 1.25 or 10ms
units.
This is especially useful when comparing related values using
different units, such as advertising interval (0.625ms units)
and periodic advertising interval units (1.25ms units).
Users will have to be aware that these macros can provide slightly
different values than what is provided, if the provided values
do not match the units.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Change downlink callback to transport data using flags.
Related to Issue #55072
Co-authored-by: Jan Kowalewski <jkowalewski@cthings.co>
Signed-off-by: romain pelletant <romainp@kickmaker.net>
Signed-off-by: Jan Kowalewski <jkowalewski@cthings.co>
Use minimized PIO code for 3-wire operation.
Input and output buffers are conventionally stored in bus byte order.
For 16 and 32 bit transfers, this is effectively big-endian, so
txbuf and rxbuf need to be read as such. Those pointers also need
to be declared uint8_t * instead of void *.
In addition, tx_count and rx_count are based on dts, and refer to
whole transfers (8, 16, or 32 bits), not bytes.
Added rpi_pico.overlay to samples/sensor/magn_polling to demonstrate
32-bit word size, and updated the README.rst to make it independent
of the specific sensor.
Clean up compliance check failures.
Fix typos.
Synchronize 3-wire TX and RX cycles.
Simplify state machine synchronization
Minimize SPI bus delay time in 3-wire mode
Move clock delay to PIO code and remove k_sleep
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Links and the manufacturer name are updated from maxim to analog.
After the acquisition of Maxim Integrated the documentation
of these devices has been moved to the analog.com website.
Redirects exist, so they are not broken yet,
but we should not rely on that.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
'nrf52840dk/nrf52840' is already listed under "generic" 'sample.dap.bulk',
so keeping 'sample.dap.bulk.nrf' has no value. The only difference is
dependency on 'gpio' instead of 'arduino_gpio', but
'nrf52840dk_nrf52840.overlay' references arduino header gpios only.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
The newly introduced `frame_incomplete` flag of
`display_buffer_descriptor` needed to be added at several places to
avoid uninitialized memory.
Signed-off-by: Martin Stumpf <finomnis@gmail.com>
Updates and fixes to support IPM sample on ESP32:
- fix IPM sample code for APPCPU and PROCPU
- align with memory layout, add flash awarenes
- shell commands to stop/start APPCPU
- reorganize overlays
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Twister's extra arguments feature only works correctly if the fully
qualified platform name is given, which was not the case. Make all
platform names for the shield testcase fully qualified to resolve this.
Fixes#80876
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
LPC54114 does not define arduino_header nodelabel, so it cannot be
supported by the shield test within the display sample. Replace with
mimxrt1010_evk, which is supported.
Fixes#80876
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Led blinking period was made configurable and time unit changed
from sec to msec recently in the source code of the sample.
Console harness regex was not changed accordingly in sample.yaml.
Device testing fails when run with twister.
Change the regex to accept any period and change the units to msec.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Remove CONFIG_MMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the mmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
mmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_SDMMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the sdmmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
sdmmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The AT / STA wifi sample is generic so it does not need to be
located under espressif board directory. Following commit
will do additional changes to make the sample more generic.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Move samples/net/wifi application to samples/net/wifi/shell
as it has been used as a shell application before.
Following commits will add new wifi samples to this directory.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
- fixes overlay-udp.conf build for platforms without TRNG.
- adds TEST_RANDOM_GENERATOR, as for most network samples.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Coverage for cmsis rtos APIS should is provided using simulation, we
should not build those on every platform we have. Avoid failures due to
incompatiblities in requirements coming from various boards and also
reduce churn and noise during testing and CI.
Fixes#80215
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change pins that are used for qdec nrf54h20dk to align with shield
(loopbacks) used in internal CI. This change is needed to start
qdec driver power management testing.
Signed-off-by: Piotr Krzyzanowski <piotr.krzyzanowski@nordicsemi.no>
The default frame rate is printed as a floating point number. Without
enabling CONFIG_REQUIRES_FLOAT_PRINTF, it is not printed at all. Fix it.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
In preparation of adding a check for dead references, this commit fixes
currently broken zehpyr_file: links.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Without this, check_compliance.py suggests to run clang-format on the
changed code lines.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This change extends what e1e19732bc
(samples: drivers: crypto: Aligned AES key) has started: For certain
architectures (i.e. Si32), the alignment of the used buffers is
important as the AES HW engine uses DMA and inherits its restrictions.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Commit e1e19732bc (samples: drivers:
crypto: Aligned AES key) introduced the alignment for the key. According
to the commit message, the intention was to align the variable at 32 bit
boundaries. For this reason, passing 32 to __aligned seems like an
error, as its argument is denoted in byte and not bits.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Remove wifi sample config files for esp32c2/esp8684, as device
isn't able to run it after memory layout update.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
- Modify the macro in source code AGT to get the right data from
device tree
- Modify name of agt node
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
This resolves some addressed comments in this PR
https://github.com/zephyrproject-rtos/zephyr/pull/77930
It adds as well a section in the documentation about some
recommendations to increase ZMS performance.
Signed-off-by: Riadh Ghaddab <rghaddab@baylibre.com>
Updates to project configuration extras to build with
Zephyr Controller.
Configure for 2 broadcast audio sources in 2 groups,
2 unicast audio source in 1 group and, 2 audio sinks
for 1 group for both broadcast and unicast usecases.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Enabled Periodic Advertising Sync Transfer feature in the
Bluetooth Low Energy HCI Controller samples.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Align Kconfig values used with bt-ll-sw-split Controller as
same used in hci_uart sample.
Relates to commit 2c6306d099 ("Bluetooth: Controller:
BT_CTLR_ISO_TX_BUFFER_SIZE from BT_ISO_TX_MTU")'.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor the sample so that multiple advertising setup can
be reused in other sample if required. Bluetooth enable can
be in the sample that reuses the advertising setup.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix buf alloc timeout to 20 millisecond as the sent callback
can have a latency that is upto twice the ISO interval.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Restrict possible maximum stream synchronization to
implementation defined 2 stream, as structure declarations
in the implementation is limited to 2.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
What is changed?
- Added a new mps3 board an552 for the soc corstone300.
The qualifier to build/run application with board mps3/an552 is
`mps3/corstone300/an552` for secure and
`mps3/corstone300/an552/ns` for non-secure.
- Added FVP variant to enable FVP testing with corstone300
and it uses the ARM FVP `FVP_Corstone_SSE-300_Ethos-U55`.
The qualifier to build/run application with FVP is
`mps3/corstone300/fvp` for secure and
`mps3/corstone300/fvp/ns` for non-secure.
- Note: the qualifier to build/run application with board mps3/an547
is now changed to
`mps3/corstone300/an547` for secure and
`mps3/corstone300/an547/ns` for non-secure.
How is it changed?
- Moved common code from mps3/an547 to corstone300.
- Renamed soc for an547 to corstone300 and added
a new soc corstone300/an552.
Why do we need this change?
- This enables FVP support and testing for corstone300.
- SOC/qualifier for mps3/an547 was renamed to reduce code redundancy
- A separate FVP variant was added for AN552 because, the TFM board
used for non-secure variant differs for FPGA and FVP.
TFM board `arm/mps3/corstone300/fvp` should be used when testing
AN552 with FVP and `arm/mps3/corstone300/an552` should be used when
testing with AN552 FPGA.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
Adds adxl362 streaming and trigger configurations to accelerometer
samples for profiling the performance impact of adding rtio support to
max32 spi and adxl362 accelerometer drivers.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Zephyr 3.7.0 has been released and it is time to remove the migration
code added in 9cf07bbdb5 (bluetooth:
Rename rpmsg HCI driver and sample to ipc).
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Removed the LE Audio specific definition and instead
refer to the value defined by iso.h as it is ISO/Core
that defines this size, and not BAP/Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The truncation is not possible in practice but add suitable cast to
avoid the warning.
samples/net/sockets/echo_server/src/tcp.c:297:54: warning:
‘%d’ directive output may be truncated writing between 1 and 10 bytes
into a region of size 5 [-Wformat-truncation=]
297 | snprintk(name, sizeof(name), "tcp4[%d]", slot);
| ^~~~~~~~~~
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Removed the generation of broadcast id inside the stack. It is now up
to the application to generate this by itself. The CAP sample has
been modified to allow either a static broadcast, or a random one.
All of this is handled in the application.
Signed-off-by: Fredrik Danebjer <frdn@demant.com>
To improve broadcast sink sample robostness the max codec meta data
size configuration is increased to reflect the meta codec data sizes
seen for sources in market.
Signed-off-by: Jens Rehhoff Thomsen <jthm@demant.com>
Originally, the net_mgmt task priority is very low. Based on roaming
implementation, roaming is triggered in net_mgmt task. When running UDP
test while doing roaming, the net_mgmt task won't have much chance to
run and roaming can't be triggered.
Increase it to 3, which is same value of supplicant task.
Signed-off-by: Hui Bai <hui.bai@nxp.com>
Added new ops and events in glue layer to support roaming.
Added new flag WIFI_NM_WPA_SUPPLICANT_ROAMING to control roaming
feature.
Signed-off-by: Hui Bai <hui.bai@nxp.com>
Add the Kconfig menu to the sample configuration.
Update sample.yaml by adding the shield configuration.
Signed-off-by: Charles Dias <charlesdias.cd@outlook.com>
This adds a user application that shows the usage of ZMS
The sample app shows three main functions of ZMS:
- read/write/delete key/value pairs
- fill all storage and delete it
- calculate free remaining space
Signed-off-by: Riadh Ghaddab <rghaddab@baylibre.com>
This sample executes some mathematical functions
that can be used for audio processing like
filtering (Fast Fourier Transform (FFT)) or
echo cancellation (Least Mean Square (LMS) filter algorithm).
This is an example that demonstrates how to include a proprietary
static library into the Zephyr build system.
The library is in an out of tree location.
To use this sample, with an out of tree library, one needs to define
an environment variable LIB_LOCATION.
If that is not defined, a default Zephyr API is used instead.
By default it uses CMSIS-DSP backend for math operations.
In README one can find more information.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
When ever `unack_queue_len` changed, should raise signal
`tx_queue_change` to let's tx_thread known queue changed.
Fixed the situation where the TX thread may no longer be sent out
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
This updates the documentation of all the Qemu boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the WeAct boards
to use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Rasperry Pi boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Segger boards to
use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Texas Instruments boards to
use the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Longan boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Atmel boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the WaveShare boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the UDOO boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the STM32 boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Quicklogic boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the NXP boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Nuvoton boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Google boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the GigaDevice boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Ezurio boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Espressif boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the BBC boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Adafruit boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This updates the documentation of all the Actinius boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
The CONFIG_DUMMY_DISPLAY is now enabled in conjunction with devicetree,
So, no need to be explicitly enabled.
Remove the setting.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Replace OVERLAY_CONFIG with CONF_FILE since the file in question
contains an alternative configuration to the one in prj.conf
as clearly stated in the sample doc
'If you use poll you should also use `prj_poll.conf` instead of
`prj.conf`.'
Signed-off-by: Abderrahmane Jarmouni <git@jarmouni.me>
Move stm32_blk.conf ouside of 'boards' as this folder is meant to
contain only board-specific devicetree overlays and Kconfig fragments.
Signed-off-by: Abderrahmane Jarmouni <git@jarmouni.me>
Die temperature polling sample is not enabled for frdm_mcxc242 board.
Add devicetree overlay and Kconfig configuration for the sample to
enable it.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Add support for building NXP WiFi. Since the driver typically requires
binary blobs, enable CONFIG_NXP_WIFI_BUILD_ONLY_MODE for this testcase.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_MBEDTLS_HAVE_TIME_DATE, which will cause that mbedtls
include Zephyr time.h and leads to 'DIV_ROUND_UP' redefined warning.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
There's no need to add conditions to CONFIG_PWM_NRF_SW, because it is
already conditioned to DT status. Right now, if any system uses both
normal PWM and "SW PWM", it needs to manually enable the driver
Kconfig.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The nRF54 and nRF92 chips has data cache, which means
the ICMsg and ICBMsg must be configured to follow required
cache alignment of the shared memory.
The `dcache-alignement` needs to be defined for that.
Signed-off-by: Dominik Kilian <Dominik.Kilian@nordicsemi.no>
For the "References" section to be useful, it needs to include a call to
the target-notes directive, which is the one that actually generates the
list of references made in the current document.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Changed dependency of the BT_BAP_SCAN_DELEGATOR to GATT_DYNAMIC_DB
from 'select' to 'depends on' and solved all loop dependencies
caused by this change.
Fixes#79108
Signed-off-by: Babak Arisian <bbaa@demant.com>
This commit fixes the following issues for adp_xc7k/ae350
1. Incorrect copyright due to copy-paste error
2. Separate RAM region for the host and remote clusters
3. Allocate hart 0 for host and hart 1 for remote cluster
4. Use mbox channel 9, 10 for the sample, leaving channel/irq source
1 ~ 8 for ae350 8-core IPI
Signed-off-by: Jimmy Zheng <jimmyzhe@andestech.com>
Add call to Z_SPIN_DELAY() to avoid issue in bsim where
time does not progress in loop causing other threads to
starve.
Signed-off-by: Johan Stridkvist <johan.stridkvist@nordicsemi.no>
remove k_work related code and change
the argument of the callback to `struct net_socket_service_event`.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Enable support for FRDM_RW612 with memc driver sample, using attached
aps6404l PSRAM.
Signed-off-by: David Missael Maciel <davidmissael.maciel@nxp.com>
Output the timestamp of the PPS timepulse when printing the fix
information, if the driver support the timepulse and it has started
toggling.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Consolidate the testcase.yaml definition for the display sample where
possible to use a single testcase for all shields. This won't work for
all testcases, but helps avoid the pattern where a new testcase using
"platform-allow" is added for every shield/board combination that needs
to be run with this sample.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Upstream NCS's library for storing Wi-Fi credentials.
This library allows storage of Wi-Fi credentials
using different backends.
Either the Zephyr settings subsystem
or the PSA secure backend can be used.
For testing purposes, credentials can be defined statically.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Signed-off-by: Gregers Gram Rygg <gregers.gram.rygg@nordicsemi.no>
Signed-off-by: Kaja Koren <kaja.koren@nordicsemi.no>
Signed-off-by: Simen S. Røstad <simen.rostad@nordicsemi.no>
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
This updates the documentation of all the Seeed Studio boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Change regex for no_multithreading test version for nRF54L15 platform.
This needs to be changed because LOG is running in MINIMAL mode.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
The buffer pointer provided to the dynamic handler should be verified
after checking the transaction status. In case upload was aborted and
underlying connection closed, the callback will get
HTTP_SERVER_DATA_ABORTED status w/o a pointer to any data.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
- boards: renesas: Add support for agt.
- drivers: counter: Add support for counter driver use agt
- dts: arm: Add support for agt.
- dts: bindings: Add support for agt counter driver.
- soc: renesas: Add support for agt counter driver.
- samples: drivers: counter: alarm: Add support for RA8
This is initial support with only basic functionality for counter
operation on Zephyr using AGT hardware, current support for
count source is limited to LOCO and PCLKB, other count source
like underflow signal external pin or AGTIO from another AGT
channel will be added in later support
Signed-off-by: Ha Nguyen <ha.nguyen.fz@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Use EXTRA_CONF_FILE in documentation .rst/.md files,
that replaced deprecated OVERLAY_CONFIG since the Zephyr v3.4 release.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
.conf files added to enable INPUT_ESP32_TOUCH_SENSOR during sample build.
The absence of these files incorrectly prevented the input_dump sample
build from failing due to missing required hal files.
Signed-off-by: Marcio Ribeiro <marcio.ribeiro@espressif.com>
Currently, the camera fixture test can only tell whether data are dumped
onto memory. This is to check further if the image content is correct.
The algorithm is rather simple: compare the average color of each bar
of a generated pattern with a predefined target in CIELAB76 color
space (which is nearly perceptually uniform).
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The logs that the fixture test are based on are not printed anymore due
to recent changes from "printk" to "LOG_DBG". Change the log level so
that it can work again.
Remove "Capture started" as it is not a relevant test regex. Logs are
sometimes not correctly printed in the console, for example, we can see:
DEBUG - DEVICE: muart:~$ [mapture started
As "Capture started" is a one-time log, fixture test will then fail due
to timeout.
Also, consolidate other regex.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The sample uses the Zephyr HTTP server library
and demonstrates the Prometheus metric
server node. Prometheus client library
runs as a pull method. The sample contains
the HTTP request counter and increases
when refresh path of '/metrics' from the browser.
Signed-off-by: Mustafa Abdullah Kus <mustafa.kus@sparsetechnology.com>
Add usage example for sys_trace_user_event, to demonstrate how users
could add tracing functionality to their application.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add EAP-TLS, EAP-PEAP-MSCHAPv2, EAP-PEAP-GTC, EAP-TTLS-MSCHAPv2,
EAP-PEAP-TLS, EAP-TLS-SHA256 enterprise wpa2 and wpa3 suiteb
support for station.
Signed-off-by: Rex Chen <rex.chen_1@nxp.com>
Use EXTRA_CONF_FILE in sample yaml files,
that replaced deprecated OVERLAY_CONFIG
since the Zephyr v3.4 release.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
This is a follow-up to commit 7a2ce2882a.
Do not enable clock control by default on nRF54H Series SoCs when
the system timer is present, because clock control is not needed
for this purpose there.
Add missing `default y` in the CLOCK_CONTROL_NRF2 Kconfig option that
enables compilation of clock control drivers for nRF54H Series.
This way modules that actually require clock control (like drivers
that use radio) will be able to enable it using the generic option
(CLOCK_CONTROL), not the above one that is specific for nRF54H.
Update accordingly applications that referenced the CLOCK_CONTROL_NRF2
option.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
SAADC peripheral for nRF54L Series allows to choose internal
voltages as positive inputs and samples shall showcase that.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Currently, Zephyr is always sending back notifications to
AP (e.g Linux in our case) on channel 0.
But this currently doesn't work if Linux uses other channel
id for communication. So, add option to use predefined
vring ID that can accomodate Linux used ID.
Signed-off-by: Alexandru Lastur <alexandru.lastur@nxp.com>
This overlay has all necessary configuration needed for Enterprise mode.
Two variants are given, once with fixed size network buffers and other
with variable size network buffers (still experimental).
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
- Fixes bug where the sample would only look at the first name type
and skip the rest.
Signed-off-by: Alexander Svensen <alexander.svensen@nordicsemi.no>
Do not apply format setting unless needed. Also, correct the check for
the RGB565 format setting- the zephyr display API treats RGB565 and
BGR565 as big endian, so the format needed here is BGR565.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for using the SMARTDMA engine on the FRDM-MCXN947 board with
the video capture sample.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Handle line_offset field within video capture sample. Other samples do
not support partial framebuffers and therefore can ignore this field.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
TI tmp1075 driver implemented based on tmp108 driver.
The driver initializes the sensor based on the DTS.
Added tmp1075 example overlay file to thermometer sample.
All you need to do to use the sensor is to connect the I2C and
optionally interrupt line.
To see default DTS configuration option inspect `ti,tmp1075.yaml`
bindings file and sensor spec.
Signed-off-by: Paweł Czaplewski <pawel.czaplewski@arrow.com>
If the Broadcast ID is initially set to 0x000000,
which is valid, comparison logic on add of an
actual Broadcast ID of 0x000000 fails.
Likewise for SID.
Moving INVALID_BROADCAST_ID define to bap.h
Signed-off-by: Lars Knudsen <LAKD@demant.com>
CONFIG_ZVFS_POLL_MAX is now used to control the maximum number of poll()
entires. Thereby, CONFIG_NET_SOCKETS_POLL_MAX is redundant and shall
be deprecated.
Modify the defaults for NET_SOCKETS_POLL_MAX and ZVS_POLL_MAX so that
the deprecation actually makes sense instead of symbol removal. In case
the application still sets the old config, it will modify the
ZVS_POLL_MAX default.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Remove the unnecessary video-controls header included in video.h.
Drivers, applications should explicitly include it when needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The mcux_acmp will get support by the comparator subsystem. To avoid
namespace clashes, namespace the driver, kconfigs and use the
MCUX_ACMP config solely to select the MCUX SDK driver.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
ZBus currently does not have a `HEAP_MEM_POOL_ADD_SIZE_ZBUS` when using
message subscribers or runtime observers, forcing the developer to set that
manually. Adding the configuration option to zbus would improve its
usability and make zbus easier to use. With this feature, zbus aligns with
the other Zephyr subsystems' heap memory allocation approach.
Signed-off-by: Rodrigo Peixoto <rodrigopex@gmail.com>
Make the blinking and fading parameters adjustable so that samples
can be run on devices that support only short periods.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Introduce BT_CTLR_PERIPHERAL_ISO_RESERVE_MAX Kconfig option
so that disabling this option will use minimum time
reservation and exercise the peripheral ISO connection event
continuation using is_abort_cb mechanism.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Introduce BT_CTLR_PERIPHERAL_RESERVE_MAX Kconfig option so
that disabling this option will use minimum time reservation
and exercise the peripheral connection event continuation
using is_abort_cb mechanism.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The sample is supposed to help examine the issues with touchscreen.
It draws a plus in last touched position.
Signed-off-by: Dominik Lau <dlau@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Remove the `work_q` parameter from `NET_SOCKET_SERVICE_SYNC_DEFINE` and
`NET_SOCKET_SERVICE_SYNC_DEFINE_STATIC` as this feature was dropped
during review but the removal was not 100% complete.
Signed-off-by: Jordan Yates <jordan@embeint.com>
IPv6 MLD API was so far defined in an internal header. This does not
seem correct though, as application code should be able to join/leave
multicast groups, hence the API should be exposed in a public header,
just as it is done for its IPv4 countepart - IGMP.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The sample uses net_config library, so there's no need for the sample to
configure unicast IP addresses manually.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Refactor the code to comply with:
Violation to rule 5.7 (Tag name should be unique) tag: data
Rename the structure to avoid excessive refactoring.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Building the sample with IPv4 only gives the following warning:
tcp.c:99:37: warning: array subscript 'struct sockaddr[0]' is partly
outside array bounds of 'struct sockaddr_in[1]' [-Warray-bounds]
data->tcp.sock = socket(addr->sa_family, SOCK_STREAM, IPPROTO_TCP);
This doesn't really seem like a valid one, but to get rid of it
workaround by specifying address family explicitly.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The host-based adv auto-resume function has both a problematic
implementation and disagreement in the community around how it should
behave. See the issue linked resolved below for details.
This patch makes the deprecation visible to the user. The user will be
better served by a auto-resume tailored their applications use case,
based on more primitive host API like `conn_cb.recycled`, which has
obvious behavior that is unlikely to change.
Resolves: https://github.com/zephyrproject-rtos/zephyr/issues/72567
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Disable CDC ACM logging in the configuration overlays used to select the
CDC ACM UART as the shell backend.
The build warning was introduced by the commit e8c4867806
("usb: cdc_acm: disable logging if used for shell with logging")
to prevent recursive logging when using the CDC ACM UART as shell or
logging backend
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
