- insert various additional information content
- use tabs to distinguish board versions
- west flash is now usable for flashing
- show steps for using USB-console
- move images to img subfolder
Signed-off-by: Bernhard Krämer <bdkrae@gmail.com>
The on-board S26HS512T 512M-bit HyperFlash memory is connected to
the QSPI controller port A1.
This board configuration selects it as the default flash controller.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Add support HyperFlash memory devices on a NXP S32 QSPI bus.
This driver uses a fixed LUT configuration that defined in HAL RTD
HyperFlash driver.
Driver allows to read, write and erase HyperFlash devices.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Create common source code to use for supporting HyperFlash.
Rename 'FLASH_NXP_S32_QSPI_NOR_SFDP_RUNTIME' to
'FLASH_NXP_S32_QSPI_SFDP_RUNTIME' as a common kconfig.
Add the 'max-program-buffer-size' property to use for
setting memory pageSize, instead of using
'CONFIG_FLASH_NXP_S32_QSPI_LAYOUT_PAGE_SIZE' for setting.
Add the 'write-block-size' propertyto use for setting
the number of bytes used in write operations, it also
uses to instead of the 'memory-alignment' property.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Following the commit f98fde07b3, DT_REG_ADDR now expands with a 'U'
suffix as an unsigned value. However, for compatibility with IS_EQ,
a raw value without any suffix is required. Therefore, this update is
necessary.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
The TMP435 is a remote temperature sensor monitor
with a built-in local temperature sensor.
Signed-off-by: Jaakko Rautiainen <jaakko.rautiainen@bittium.com>
Set ctrl9_xl.device_conf bit to 1 in ism330dhcx_init_chip()
prior to start device configuration, as stated in paragraph
9.20 of the datasheet.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
cmake: Added "-" support to EXTRAVERSION.
Added to the regex and update the documentation.
Also updated the examples in the documentation.
Signed-off-by: Nick Brook <nrbrook@gmail.com>
cmake: Allow semver style EXTRAVERSION
Semver versions are commonly in the form X.X.X-a.1, X.X.X-beta.2, etc.
However, currently EXTRAVERSION cannot include ".". This change allows it.
Signed-off-by: Nick Brook <nrbrook@gmail.com>
The connection event at the connection update instant was
skipped due to previous ticker node in use that is being
stopped was registering a relative occupied time that
overlapped with the new ticker node being started for
scheduling the connection with new interval.
Added mock interface for ticker_stop_abs() hence needed by
the Controller unit testing.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add a test validating that Zephyr can compile with the 3 underlying
filesystems enabled with only `CONFIG_FILE_SYSTEM_LIB_LINK` enabled.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Update the Kconfig configuration to allow enabling the underlying
filesystems (e.g. exFAT), with only `FILE_SYSTEM_LIB_LINK` enabled.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The compiler is unaware of the `block_size > 0` precondition, so it
outputs warnings of uninitialized `reclen`. Explicitly initialize the
variable to suppress this.
Signed-off-by: Jordan Yates <jordan@embeint.com>
SMI bus error check mechanism is preventing the host SMI bus to be
interferred by noise on board level. Current implementation is checking
if data which is writing to/reading from the PHY has correct CRC sum.
If not, then writing/rading process is repeated by the number of
attempts defined in the KConfig. If repeating transmission will fail
by the numbers of ettemps defined in KConfing, drivers returns an
error.
Signed-off-by: Robert Slawinski <robert.slawinski1@gmail.com>
For GIC multiple views feature support, all GIC Re-distributor's
GICR_TYPER.last will be set. Because configuration view-0 can
assign non-contiguous CPUs to views other than 0, in this case
the GIC Redistributors' registers won't seem contiguous.
So the GIC driver should cope with multiple sets of redistributors
like multi-chip scenarios. In this patch we add multiple GIC
redistributor regions support in GIC redistributor iteration.
For more information, refer to the Multi view subsection
in the GIC Technical Reference Manual.
For example:
https://developer.arm.com/documentation/101516/0400/Operation-of-GIC-700/Multi-view
Signed-off-by: Ziad Elhanafy <ziad.elhanafy@arm.com>
Certain HCI events, like advertising reports, are of less importance than
others. This takes the discardable buffer pool into use for such events.
When the system is flooded with advertising reports, discarding some of
them ensures that the system can still handle other events.
Signed-off-by: Kalle Kietäväinen <kalle.kietavainen@silabs.com>
The BT Link Layer needs to get runtime in a timely manner to keep
connections alive and handle other time-critical tasks. This is achieved by
adding a separate thread for it with a meta-IRQ priority, which means it
can preempt other threads. The driver also has an RX thread that passes HCI
messages from the controller to the host stack. This can be a lower
priority cooperative thread, as it doesn't have strict timing requirements.
Signed-off-by: Kalle Kietäväinen <kalle.kietavainen@silabs.com>
Only reserve L2 header for TX case when allocating net buffer,
as for RX case, all the received headers are already in linear
buffer when the driver receives the data, and reserve extra L2
header for RX case may exceed the default buffer size.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
bt_gatt_find_by_uuid used bt_gatt_attr_value_handle but that
function only works to get the value handle of a characteristic
declaration, i.e. if the UUID is not BT_UUID_GATT_CHRC then it
would always return handle = 0. This meant that
bt_gatt_find_by_uuid would always use handle = 0 as the starting
handle for non-BT_UUID_GATT_CHRC attributes, instead of the handle
of the provided attr.
This was not an issue for any UUIDs that may only exist once on a
GATT server, which is most UUIDs, but for UUIDs like the
BT_UUID_TBS_* UUIDs that may be multiple instances of, it would
always return the first attribute rather than the one starting
from the provided start attr.
This commit also ensures that we do not overflow the `end_handle`
when adding 2 uint16_t values.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Changes the priority of imgtool so that the preferred version is
the one inside of the MCUboot directory
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
When using asynchronous API, transfer will fail if the source buffer is
located in a region that cannot be accessed by DMA. This could happen
when a buffer is declared const, and placed in flash memory, for
example.
Workaround this problem by loading the data into a set of temporary
caches before passing them to DMA.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
This commit adds asynchronous mode support to MAX32 UART driver. Each
direction uses a single DMA channel that is assigned in devicetree
configuration.
Asynchronous mode also depends on interrupts to refresh receive
timeouts.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
Application won't wakeup without external trigger in
the analog comparator wakeup configuration.
Therefore removing post-wakeup lines from sample regex as they are not
expected to occur in default testing scenario (without external triggers).
Signed-off-by: Bartlomiej Buczek <bartlomiej.buczek@nordicsemi.no>
In the application, after the sysjump, the RX interrupt might remain
enabled. During initialization, once the IRQ is enabled, the RX
interrupt could be triggered if there is any traffic on the RX line,
potentially causing an interrupt storm.
This change disables the UART RX interrupt at the driver initialization
to prevent this issue from occurring.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
The MAX22017 is a two-channel industrial-grade software-configurable
analog output device that can be used in either voltage or current output
mode.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Add comment to DTS file about SRAM partitions similar to the RTXXX
series has comments.
Add also a doc section to the frdm_rw612 about this.
Also fix the section hierarchy of the frdm_rw612 doc, the header levels
were wrong since the wifi and bluetooth, and reference sections were
under the debugging section.
Group all the wireless connectivity info together.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The broadcast assistant will now validate the content of the
received receive states.
Some modifications were done to the tests to properly
pass these new validations.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Main changes since v2.4:
* libRandv2: New API to fill buffers & Wextra warning fixes
* libCryptov1: Add new AES-ECB API
Note: Like before, bsim remains fully backwards compatible
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Write-back cache after copying VPR's code and data to the destination
memory. It allows VPRs to run from RAM regions cacheable by its host.
It allows to use FLPR in nRF54H20.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
This is a follow up to commit 770482a45a.
Add initialization of the `ok` variable to prevent the "may be
uninitialized" warning when `CONFIG_BOOTLOADER_MCUBOOT` is not
defined.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Have the application enable this feature explicitcly, so that
simple applications do not need to disable this to get the
expected behavior.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
