This commit adds asynchronous mode support to MAX32 UART driver. Each
direction uses a single DMA channel that is assigned in devicetree
configuration.
Asynchronous mode also depends on interrupts to refresh receive
timeouts.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
The MAX22017 is a two-channel industrial-grade software-configurable
analog output device that can be used in either voltage or current output
mode.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Add comment to DTS file about SRAM partitions similar to the RTXXX
series has comments.
Add also a doc section to the frdm_rw612 about this.
Also fix the section hierarchy of the frdm_rw612 doc, the header levels
were wrong since the wifi and bluetooth, and reference sections were
under the debugging section.
Group all the wireless connectivity info together.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add support for the Antmicro's Myra SiP Baseboard. The board uses
Antmicro's Myra SiP which integrates STM32G491XX MCU and its SoC
configuration.
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Add `smb-wui` property to support wake-up from sleep mode by START
condition when i2c is configured to target mode.
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Support OSPI flash driver on EK-RA8M1 and EK-RA8D1 with ospi_b
and S28HL512T flash.
Signed-off-by: Tri Nguyen <tri.nguyen.wj@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Add inverted flag to bindings, as pwms field is supposed
to be used by application only.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
This adds support PWM EMIOS for NXP S32Z SoC, both PWM pulse
generate and pulse capture are supported
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Removing period, duty and polarity configuration from
channel devicetree. At boot time, only minimal setup like
pinctrl, prescaler, etc should be initialized. PWM signal
is produced by using pwm_set* API
Also after this change, PWM period, duty are changed at the
next counter period boundary
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Fixes the CMake Warning on build/zephyr/zephyr.dts:
Warning (spi_bus_bridge): /soc/xspi@47001400: node name
for SPI buses should be 'spi'
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fixes the CMake Warning on build/zephyr/zephyr.dts:
Warning (spi_bus_bridge): /soc/octospi@52005000: node name
for SPI buses should be 'spi'
<stdout>: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fixes the CMake Warning on build/zephyr/zephyr.dts:
Warning (spi_bus_bridge): /soc/octospi@52005000: node name
for SPI buses should be 'spi'
<stdout>: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add clock source to timers which indicates maximum frequency of
the timer instance.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
i2s driver have not suooprt frdm_mcxn947 pll clk set.
so add macro CONFIG_I2S_HAS_PLL_SETTING to control pll init.
Signed-off-by: Qiang Zhang <qiang.zhang_6@nxp.com>
Implement lan865x mdio driver to provide interface between lan865x MAC
driver and internal PHY driver phy_microchip_t1s.c. This driver is needed
to support the driver architecture followed.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Remove internal PHY initialization part as the phy_microchip_t1s.c
driver will do the internal PHY initialization.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Add support for LAN8650/1 Rev.B1. As per the latest configuration note
AN1760 released (Revision F (DS60001760G - June 2024)) for Rev.B0 is also
applicable for Rev.B1. Refer hardware revisions list in the latest AN1760
Revision F (DS60001760G - June 2024).
https://www.microchip.com/en-us/application-notes/an1760
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Add a DTS binding for the MediaTek Audio Front End device, and
definitions for the in-tree devices.
These .dts files were auto-generated from pre-existing SOF code (that
defined the devices as C structs) using a tool currently being
submitted in the SOF tree, thus are included here as separate files.
The expectation is that future variants will be authored in this
format directly. Longer term we can move them directly into the core
board DTS.
Signed-off-by: Andy Ross <andyross@google.com>
Add zephyr,bt-hci-uart binding to the CYW43xxx device tree example to
properly implement Zephyr's HCI UART abstraction layer.
Signed-off-by: Benjamin Geiger <BenjaminGeiger1@gmail.com>
Add initial SoC support for the TI J722s SoC series MCU-domain
Cortex-R5 core.
TRM for J722s: https://www.ti.com/lit/zip/sprujb3
Signed-off-by: Andrew Davis <afd@ti.com>
Add initial SoC support for the TI J722s SoC series MAIN-domain
Cortex-R5 core.
TRM for J722s: https://www.ti.com/lit/zip/sprujb3
Signed-off-by: Andrew Davis <afd@ti.com>
Add wsen_pdus_25131308XXXXX driver with
the corrected name and compatibility with
the hal update as well as added new features..
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Change the property names in the bindings and DTS
to use hyphens(-) for separation instead of underscores(_).
Signed-off-by: James Roy <rruuaanng@outlook.com>
Defined default values for baudrate, parity, stop bits, and data bits.
This removes complexity and obfuscation from the code.
Signed-off-by: Yishai Jaffe <yishai1999@gmail.com>
This commit adds MBOX device tree entry for MCXN947.
Adds support for MCXN in NXP ipm and mbox drivers.
Signed-off-by: Tomas Galbicka <tomas.galbicka@nxp.com>
