drivers/input/input_gpio_keys.c requires property "zephyr,code" must
be provides for gpio-keys, so add code property for imx93_evk A55
and M33 boards.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Enable i2c and configure it to read accelerometer sensor on the board.
Test it using sample.sensor.accel_polling.
Signed-off-by: Neil Chen <cheng.chen_1@nxp.com>
mcxc444 also has pit and rtc counters, add the counters to
board documentation, and enable it explicitly in board dts.
Set rtc clock to 32 kHz oscillator.
Signed-off-by: Neil Chen <cheng.chen_1@nxp.com>
For Zephyr Cortex-A Core supports on NXP boards imx8mm, imx8mn, imx8mp,
imx93 and imx95, currently use DDR DRAM memory as Zephyr memory, so
change RAM dts nodes name to be "dram" in order to reduce confusion.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
- Adds 'supported: flash' to all NXP board .yaml
with enabled flash controller support.
- Sorts supported features alphabetically.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Change running baudrate from `115200` from `3000000`.
Implement the function `bt_h4_vnd_setup` to update the HCI bandrate.
Add Kconfig `BT_H4_NXP_CTLR_WAIT_TIME_AFTER_BAUDRATE_UPDATE` to set
the waiting time after the controller bandrate HCI vendor specific
command sent. It is used to ensure the controller is ready to update
HCI bandrate.
Select `BT_HCI_SETUP` if `BT_H4_NXP_CTLR` is enabled.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
- Fixes MCUBoot build error when enabled Serial Recovery via USB CDC ACM.
- Increases MCUBoot partition size.
Signed-off-by: Andrej Butok <Andrey.Butok@nxp.com>
- Trace32 runner: no need to configure TE bit in CFG_CORE
register in the cmm start-up script, it can be configured
at Zephyr start-up code when required (via SCTRL register)
- MPU static regions also needs to be updated for XIP and
non-XIP
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Add devicetree node for code RAM, code RAM can be accessed
over AIXM bus or AXIF bus. Code access via AXIF interface
provides the best optimal performance
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
The NXP LCDIC peripheral contains two internal timers, with configurable
periods. These times are used to determine delays within the peripheral,
such as the reset and tearing enable signal delays. Allow these periods
to be set within the devicetree for the peripheral.
Raise the period where required for display drivers that need a value
other than the reset setting
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add note about compatible change for NXP PORT IP. Also, update
references to the DT compatible within board docs.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
USE_HYPERRAM macro defined shouldn't be placed under
CONFIG_BOOT_FLEXSPI_NOR.
Add flexspi1 pinmux pinctrl and flash partitions
Add flash partitions and correct flash parameter.
This commit was tested with samples: flash_shell on cm33/cm7 cores
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
The prior image was of poor quality, making it difficult to interpret.
Updated the image with a higher-quality version.
Signed-off-by: Dhruv Menon <dhruvmenon1104@gmail.com>
Add UART configuration and pin control. Set state to disabled,
as it serves as alternative to default LPUART0 or as second
uart only.
Signed-off-by: Neil Chen <cheng.chen_1@nxp.com>
- Refactoring of the cmake code so LinkServer can be invoked with the
correct switches.
- Documentation update
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
- Sets s26ks512s0 flash write-block-size to correct 256KB.
- Optimizes MCUboot partitions to fit the correct write-block-size.
Fixes#80284
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Flash support for RT1170 EVKB was fixed with cfb7322107 (drivers: flash:
flash_mcux_flexspi: add support for W25Q512NW-IQ/IN). Document this
support in the board page.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
mdio_enet_nxp driver accesses the registers of its parent node Ethernet MAC
This commit enables this node in mimxrt1062_fmurt6 board's device tree.
This also fixes Issue #80881
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Remove CONFIG_MMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the mmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
mmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_SDMMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the sdmmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
sdmmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
SOCs using ECC require the SEGGER RTT control block address to be
provided to the tooling, as the SEGGER tools will not scan the memory
range of ECC ram. Add documentation making this clear to boards with
these SOCs.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
WS25Q512JV can only run at 104MHz at 3.3V, unless the read parameter
bits are changed. Since we don't reprogram these currently, reduce max
frequency to safe value
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The LPC55S36 board has an integrated MCU-Link debug probe, not an
LPC-Link2. Also, it is now possible to directly use the stock CMSIS-DAP
mode with the `linkserver` runner.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
mcxc242 has usb device capability. Add usb to board documentation and
to the yaml file. Enable and configure it in board dts.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
This updates the documentation of all the NXP boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
For the "References" section to be useful, it needs to include a call to
the target-notes directive, which is the one that actually generates the
list of references made in the current document.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Updated imx8mm/n/p and imx93 Cortex-A Core supported features in board
yaml file, and also fixed ram size for the board.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
IS25WP flash chips support 133MHz only when P[6:3] is programmed, which
will not occur during the SFDP probe sequence used in the FlexSPI nor
driver. With the default P[6:3] value, the best frequency supported for
read instruction 0xEB is 104MHz, so set this for all boards using this
flash chip with the FlexSPI nor driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
- add ITCM definitions (for LinkServer) in board.cmake
- update of soc.c to support RAM images (stack pointer)
- doc update
Change applies to both versions of the MIMXRT1170 EVK
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Apply this overlay to test RFU_BTN1 and RFU_BTN2 on PCAL6524.
The user buttons RFU_BTN1 and RFU_BTN2 is connected to i.MX 93 GPIO by
default, but can be changed to connect to onboard GPIO expander
PCAL6524. To do this, switch SW1006 to 0000, then switch SW1005 to 0101.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Current code does no longer support
the non monolithic feature.
Hence, removing unnecessary code.
Signed-off-by: Yassine El Aissaoui <yassine.elaissaoui@nxp.com>
Enabled the MRT at the board level for
mcxn947. Enabled the clocking for the MRT
in the clock control.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Enable the irqstr interrupt controller for the adsp-based
imx8mp.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Enable dma boards/test for S32Z270.
The non-cacheable memory used for DMA tests (chan_blen_transfer and
loop_transfer) is split from the system SRAM.
Signed-off-by: Ha Duong Quang <ha.duongquang@nxp.com>
The Drivers using Pinctrl should be turning Pinctrl on
this should not be the responsibility of the board. This
commit removes CONFIG_PINCTRL from the boards side for nxp boards.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Use SW2 instead of SW3 for entering MCUboot serial recovery/USB DFU
mode. Holding SW3 during reset results in a NMI, causing the boot process
to halt.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for SMARTDMA camera engine, and a OV7670 parallel camera
definition for the frdm_mcnx947 board. This support has been tested with
the video capture sample.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for LPI2C7. This peripheral is used for interfacing with
cameras connected to the J9 header.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable LPI2C1 on the frdm_mcxw71 board which is connected to a
FXLS8964AF sensor (no driver for the sensor yet).
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Board frdm_mcxc242 does not have UART IP configured.
Add UART configuration and pin control. Set state to disabled,
as it serves as alternative to default LPUART0 or as second
uart only. Add uart to supported features in yaml.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Full name was set based on the information available either in board
documentation or in Twister files.
Whenever applicable, vendor name was dropped from the full name so that
all boards have a consistent naming scheme.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
mcxc242 has lptmr, pit and rtc counters, but it is not documented and
not listed in frdm_mcxc242.yaml.
Add the counters to board documentation, to the yaml file, and enable
it explicitly in board dts. Set rtc clock to 32 kHz oscillator.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
