Add a GPIO driver for the Microchip MEC5 HAL based chips.
Current devices are: MEC174x, MEC175x, and HAL version of
MEC172x named MECH172x.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add max22190 gpio driver with input functionality, since device
support only input without output.
Implemented diagnostic functionality for all 8 channels
which include various check to over/under voltage and wire break.
Filtering configuration is done from devicetree on per channel
bases and is configured on chip start.
In case some fault condition occure FAULT pin drive LOW which
prop to FAULT registers to be read. Data is stored in data structure
for furter analizes and ERR message is printed in console.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
Add support for GPIO controller feature of AW9523B.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Co-authored-by: Benjamin Cabé <kartben@gmail.com>
Industrial 8 channel output with advanced diagnostics.
Allowing giagnostic configuration both on per channel or global bases
In SPI communication diagnostic status transmitted on every
READ/WRITE which includes generic status of chip.
Diagnostics includes :
* Oveload
* Open Wire
* Over current
* Short to VDD
* Thermal Shutdown
* VDD Warn
* Watch Dog Error
* Communication Error
* VDD under voltage
Add app.overlay for MAX14916 driver.
Tested with adopted basic/blinky example.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
MAX14906 in 4 channel I/O with advanced diagnostic.
In SPI communication diagnostic status transmitted on every
READ/WRITE which includes generic status of chip.
Configuration both on global level and on per channel bases.
Diagnostics includes :
* Thermal overload
* current limit
* open wire detection
* short to VDD
* Above VDD
* Safe DEmagnitization fault
* VDD warning
* VDD low
* SPI/CRC Error
* WDog Error
* Loss GND
Add app.overlay for MAX14906 driver.
Tested with adopted basic/button and basic/blinky sample.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
There are numbers of drivers for different PCA(L) series chip. They
share similiar register layout and control logic. This driver intends
to unify these drivers for PCA(L)xxxx series i2c gpio expanders.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
This is just the driver for banks 0 to 3. Bank 4 will come via a
separate commit since it needs a different driver.
Signed-off-by: Michael Zimmermann <michael.zimmermann@grandcentrix.net>
Background of this modification is to make gpio driver code
provided by Renesas vendor to be an official support for Renesas
MCU on Zephyr
Signed-off-by: Quy Tran <quy.tran.pz@renesas.com>
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
This chip is handled by the more generic mcp23xxx driver, which will get a
microchip,mcp23s17 compatible binding in the next commit.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
This is the initial commit to support for gpio driver
for RA8M1 MCU, the coding is base on renesas fsp hal
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Add mfd_adp5585 and gpio_adp5585 driver. This driver enables ADP5585
as an GPIO expander.
This chip is used as an GPIO expander on i.MX93 EVK. GPIO pinctrl,
read/write and interrupt is supported.
Note that ADP5585 has 2 GPIO banks with 5 pins each. The driver combines
two group into a 16-bit port. Index 0~4 correspond to R0~R4 lines, index
8~12 correspond to C0~C4 lines. Index 5~7 is reserved unavailable.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Rename ad5592 files in dts, driver and include to ad559x and add support
for I2C bus which is required for AD5593.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add RGPIO gpio driver. This driver is used for i.MX93 and i.MX8ULP.
GPIO pinctrl, read/write and interrupt is supported. Runtime mmio
configuration is enabled, so no need for region definition in
mimx9/mmu_region.c
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Add Renesas rzt2m gpio driver with basic functionality.
It supports pin mode configuration and writing/reading to/from gpio ports.
Includes dts changes to build blinky sample.
Signed-off-by: Jakub Michalski <jmichalski@internships.antmicro.com>
Add initial support for Renesas RA GPIO.
To avoid complicating the initial code for supporting the SoC,
I have implemented only the bare minimum for now.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
The BCM2711 SoC exposes 58 GPIOs. The first 28 (bank 0) are accessible
to users via the 40-pin header, while the others (bank 1) are used for
controlling on-board peripherals.
This also update doc of `rpi_4b` board.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Davinci gpio controller support to add various soc gpio
support (J721E, AM654).
TRM for J721e https://www.ti.com/lit/zip/spruil1
File: spruil1c.pdf
GPIO: section 12.1.2
BeagleBone AI_64 https://beagleboard.org/ai-64
Signed-off-by: Prashanth S <slpp95prashanth@yahoo.com>
AXP192 is a small power management IC, that also
features 5 GPIOS.
Besides GPIO driver this commit also includes needed modifications
in axp192 regulator and mfd driver as LDOIO0 functioanlity
is multiplexed with GPIO0 pin.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
Split the SDL GPIO emulator driver in a top and bottom
to enable using it with embedded libCs.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This adds a few line use zephyr_syscall_header() to include
headers containing syscall function prototypes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Port the gpio_keys_zephyr driver from the gpio subsystem with a
dedicated API to the input subsystem reporting input events.
Move the test as well, simplify the cases a bit since the API is simpler
now.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Added initial version of Infineon CAT1 GPIO driver.
Added initial version of binding file for Infineon CAT1 GPIO driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
