The west packages extension can be used to install module dependencies.
Upstream nanopb has added the pip package dependencies to the
zephyr/module.yml file. Remove in-tree pip package dependencies.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
This commit enables I2C2 on nucleo_u083rc board
for i2c_target_api test.
Signed-off-by: Mohammad Badawi <zephyr@exalt.ps>
Signed-off-by: Sara Touqan <zephyr@exalt.ps>
Since DMA is supported by the nucleo_u083rc board, it should be enabled
in the board overlay for the ADC adc_api test, similar to the board
nucleo_h743zi.
Signed-off-by: Mohammad Badawi <zephyr@exalt.ps>
Signed-off-by: Sara Touqan <zephyr@exalt.ps>
This commit Modifies the DMA STM32 Kconfig to enable shared IRQ
support for the STM32U0 series.
This change ensures DMA channels with shared IRQs are properly
configured for stm32u0 devices.
Signed-off-by: Mohammad Badawi <zephyr@exalt.ps>
Signed-off-by: Sara Touqan <zephyr@exalt.ps>
This commit enables support for DMA,
SPI, RNG, Crypto, USB and RTC.
Signed-off-by: Mohammad Badawi <zephyr@exalt.ps>
Signed-off-by: Sara Touqan <zephyr@exalt.ps>
This commit Introduces DTS configurations for DMA,
SPI, RNG, Crypto, USB and RTC modules to enable
support in STM32U0.
Signed-off-by: Mohammad Badawi <zephyr@exalt.ps>
Signed-off-by: Sara Touqan <zephyr@exalt.ps>
Now expected vs read size will be logged in case of error
to make it easier to understand problem or correct test
settings.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The clock_stm32_ll_common.c function set_up_plls calls
LL_RCC_PLL_Disable();and it was not waiting for the
disable to complete before trying to configure
the pll sysclock which creates a race condition for
pll configuration.The wait for re-enabling the RCC pll
is already there, it was just missing the wait for
the disable before configuration. Also added the wait for PLL2.
Signed-off-by: Benjamin Curtis Byers <ben.byers@ubcobikes.com>
Wrap `sigaction()` declaration with `TOOLCHAIN_IGNORE_WSHADOW_BEGIN`
and `TOOLCHAIN_IGNORE_WSHADOW_END` to ignore Wshadow warning
which occurs because `struct sigaction` already exists.
fixes: #83111
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
Use the net_icmp_send_echo_request_no_wait() when sending
ICMP Echo-Req so that we can avoid the warning message from
system workqueue handler.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Create a net_icmp_send_echo_request_no_wait() variant that will
not wait when allocating net_buf to be sent. This variant will avoid
a warning to be printed when sending Echo-Req from a system workqueue
because the work cannot sleep in this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The CONFIG_ZEPHYR_HAL_TDK_MODULE is always set if the module is on disk,
introduce an implied symbol to prevent a cmake warning if no TDK drivers
are needed.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Once proxy gatt is enabled, due to the nature of gatt advertisements
being continuous, the controller will reject starting the scanner after
enabling proxy gatt. As such we should start the scanner first.
Currently the order works as we are using k_work to postpone the proxy
gatt service registration, because services can't be registered between
initializing BT and loading the settings.
Once we start using the new settings priority feature, we are sure to
envoke enabling proxy gatt after loading the settings, so the delayed
enabling can and should be removed.
This preventetive fix has been tested by running relevant bsim tests
after rearranging in which order the settings of the subsystems are
loaded via `h_commit`.
Signed-off-by: Kyra Lengfeld <kyra.lengfeld@nordicsemi.no>
Adapt the stm32 flash driver for the stm32h7rs serie where some
bit of the FLASH registers are named differently from stm32h7 serie.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch will save configured link clock and ensure
ssp starts with xtal clock if ssp ver >= 2.0
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
As per BHC-750 in TCAT case for now only allowed devices
are the ones that have either dual radio or multiplexed
radio capabilities. So the 'M' bit in BLE advertisement
should be always set to 1. In future specifications
devices without multiradio capabilities will be allowed
this is the reason why new Kconfig was introduced.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Add an integration platform to the LoRa samples so that changes to these
applications are checked in the PR CI.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Create a special Ethernet interface that supports link layer
embedding. Add a test that uses this special Ethernet interface
to verify that the L2 header is embedded to the first net_buf.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If Ethernet based network device driver is advertizing
ETHERNET_EMBEDDED_LL_HEADER, then the L2 driver will can
return the proper L2 header size for the network interface.
This info is then used in TX to determine whether to have a
separate net_buf for the link level header, or to embed the
header to the same net_buf as the L2 payload.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Allow network device driver to configure the system so that
when a network packet is sent to it, the link layer header
is stored just before the L2 payload in the same packet.
Currently the link layer header is stored in a separate
net_buf that is linked in front of the L2 payload.
This option can typically save one net_buf when sending
a network packet. Note that if you are using variable data
size buffers (CONFIG_NET_BUF_VARIABLE_DATA_SIZE) then this
embedding is not needed because one can allocate just the
right size network buffers and not waste any memory.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Make sure we send IGMP report when re-joining the multicast group
when interface goes up after operative down event.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If network interface goes operative down, then re-join user defined
IPv4 multicast groups that where joined earlier when the interface comes
up again. If user takes the network interface down manually (admin down),
then the user specific groups are not re-joined. This works now the same
way as IPv6 re-joining.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add dts node to support for gpio interrupt on Renesas RA SoC
- Add external interrupt node
- Add gpio interrupt pins
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
First commit to add support for gpio interrupt on Renesas RA
- Add support for external interrupt driver
- Add support for gpio interrupt config
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Move ioport6, ioport7, ioport8 to r7fa6m4ax due to it is common
part of RA6M4
Impacted file:
- dts/arm/renesas/ra/ra6/r7fa6m4ax.dtsi
- dts/arm/renesas/ra/ra6/r7fa6m4af3cfb.dtsi
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
The ecpprog command is an utility written by Greg Davill for flashing
FPGAs such as ECP5 or CrossLink-NX series. Devkits typically have an
FTDI interface chip to access the external flash. FPGA image is
typically at flash offset 0x00000000 flash offset, and the Zephyr
image offset can be set via CONFIG_FLASH_LOAD_OFFSET.
Signed-off-by: Josuah Demangeon <me@josuah.net>
The `_resv0` field is no longer needed after increasing the size of
`iodev_flags` from `uint16_t` to `uint32_t` by this PR #80177.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
There is an unused variable, which may result in a compiler warning.
Since we can not guarantee the value of this variable
we can not test for it, so it is removed.
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
