Add hwinfo driver for Silicon Labs Series 2 devices. The driver
is separate from the Series 0/1 Gecko driver because the available
reset causes are completely different.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
This PR fixes the issue that building the driver with either
CONFIG_RTC_CALIBRATION=y or CONFIG_RTC_ALARM=y and without
'int-gpios' used will cause
'undefined reference to `rv8803_write_reg8'' error.
Signed-off-by: Marcin Lyda <elektromarcin@gmail.com>
Some time ago a new shim for nRF UARTE was added (uart_nrfx_uarte2.c)
which used nrfx_uarte.c driver underneath. It was supposed to support
nrf54x platforms. However, later on legacy driver (uart_nrfx_uarte.c)
was extended to support nrf54x platforms and it takes less code size,
has better performance and more features. Shim uart_nrfx_uarte2 will
no longer be supported. As new shim is the default and there is a
Kconfig to pick the legacy shim (CONFIG_UART_NRFX_UARTE_LEGACY_SHIM=y)
it cannot be deprecated in the normal way. Additional Kconfig option
is created (DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM) which is enabled
if CONFIG_UART_NRFX_UARTE_LEGACY_SHIM=n and it selects DEPRECATED.
A warning was also added to the CMakeLists.txt.
Patch removes use CONFIG_UART_NRFX_UARTE_LEGACY_SHIM in tests.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
In order to ensure that watchdog channels are freed in proper
driver state, synchronization in form of simple loop needs
to be added after stopping. In no irq variant, it is already done
on nrfx level. NRFY function can be replaced by NRFX one in
the future.
Signed-off-by: Michał Stasiak <michal.stasiak@nordicsemi.no>
Simplifies GPIO reset logic in `phy_mc_ksz8081_reset()` by introducing
a dedicated function, `phy_ksz8081_reset_gpio`. If this function returns
`-ENODEV`, it will fall back to using a command-based reset instead.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Simplifies error handling in `phy_mc_ksz8081_get_link()` by
centralizing mutex unlocking with a `done` label.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Link layer needs some fixing before hci driver can be minimally configured
and hence must revert conditional inclusion of core functionalities untill
new link layer is available.
Signed-off-by: Petri Pitkanen <petri.pitkanen@silabs.com>
Several driver setting were as defines in driver file which made hard to
change by application programmers. Fixed by adding
silicon labs specific Kconfig file for bluetooth driver configurations.
Also some cleaning for handling Kconfig conditional to conform
preferred style.
Signed-off-by: Petri Pitkanen <petri.pitkanen@silabs.com>
RTIO correctly declares tx buffers as const, however, the
existing I2C API and NRFX (SDK) drivers don't. Therefor cast the
const buf to non-const when passing the tx buf to the twim driver
from the RTIO call to avoid the const warning.
The tx buffer is being treated as const data naturally in the
NRFX driver, its just not declared as such since we reuse the
buffer for both RX and TX data.
Alternatively the SDK and "shim" drivers built on top of it need
to be updated, which is quite a bit of work :)
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Multi channels share one IRQ, add channels-shared-irq-mask on RT1180
attribution to describe the channel shared status, and add code
implementation to register the handler function for each channel
in different interrupts.
Fix legacy building warning issue
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
add support SCE9 to entropy driver for Renesas RA
Signed-off-by: Minh Hoang <minh.hoang.wm@bp.renesas.com>
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Enables the fractional-N (FRACN) setting for PLL1 in the STM32H5XX
clock driver.
This feature allows achieving a system clock frequency of 250 MHz from
an 8 MHz `clk_hse`.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Exit the init earlier when XSPI is in memory map mode. Avoid
unnecessary checks and prevent pin reconfiguration that might
cause line spikes. Clock check beforehand is preserved.
Remove '\n' from the LOG_DBG string.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Exit the init earlier when OSPI is in memory map mode. Avoid
unnecessary checks and prevent pin reconfiguration that might
cause line spikes. Clock check beforehand is preserved.
Remove '\n' from the LOG_DBG string.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
We add a serial UART driver for Microchip MEC5 HAL based chips.
The driver supports polling, interrupts, and runtime configuration
features. Power management will be implemented in a future PR.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This macro is defined in a few places which leads to macro redefinition
error e.g. when compiling prometheus network sample for NPCX boards.
Provide one definition of IS_BIT_SET() in util_macro.h to fix the
problem.
Signed-off-by: Patryk Duda <patrykd@google.com>
Move the instance pointer, which is a constant value, into a dedicated
config structure. At the same time, remove the type casting macros as
this pattern has been removed from the tree for some years now.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The STM32 IWDG is a single channel watchdog, and therefore should be
returning `-ENOMEM` when a user attempt to install additional timeouts,
instead of overwriting previous values.
Signed-off-by: Jordan Yates <jordan@embeint.com>
the following implementations are added:
- set cyclic variable to handle circular/normal mode :
enable dest/source_reload_en variable to set CIRC bit to 1 for RX or TX.
- DMA_STATUS_COMPLETE(0), DMA_STATUS_BLOCK(1) macros to handle half
and full irq
- add ASYNC_UART_STATUS_TIMEOUT(3) macro to work with default mode
- add status input in uart_stm32_dma_rx_flush function to handle
async events depending on the mode we are in.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
co-authored-by: Cyril Fougeray <cyril.fougeray@worldcoin.org>
Mostly a revert of commit b1def7145f ("arch: deprecate `_current`").
This commit was part of PR #80716 whose initial purpose was about providing
an architecture specific optimization for _current. The actual deprecation
was sneaked in later on without proper discussion.
The Zephyr core always used _current before and that was fine. It is quite
prevalent as well and the alternative is proving rather verbose.
Furthermore, as a concept, the "current thread" is not something that is
necessarily architecture specific. Therefore the primary abstraction
should not carry the arch_ prefix.
Hence this revert.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The bus recovery feature utilizing bit-bang operations, which sends
SCL clock pulses to recover the bus and checks if the line is down.
Upon recovery, it disables the system test register before resuming
the transactions.
Signed-off-by: Dhruv Menon <dhruvmenon1104@gmail.com>
The OMAP I2C provides support for I2C serial interface on TI K3 series.
It is compatible with Philips I2C physical layer.
The commit includes:
Zephyr i2c api implementation
Polling Mode
Signed-off-by: Dhruv Menon <dhruvmenon1104@gmail.com>
The dma callback functions were written in a very confusing way, clean
them up, and this change also saves some bytes of ROM.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
move copy pasted code into common spot for when there is an invalid
configuration passed to the config function
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
There's no need to put an if before i2s_purge_stream_buffers,
because this is handled already by the boolean values entered to the
function
Also remove the inline of the function, which allowed the compiler to
make optimizations and save some bytes.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Put DT_DRV_COMPAT at top of file by custom
Consolidate logging macros
Clean up checks and use build assert
Remove header file which was not necessary
Remove unnecessary forward declarations
Fix the type of the stream state to be more precise, it is used as the
enum i2s_state type. This requires handling all the enum cases in switch
statements
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Move the cmake file of OSAL to it's own repo and build as a standalone
library, this is porting friendly.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The "nm_bsp_reset" is used to apply a hard reset to the WINC board by
setting CHIP_EN and RESET_N signals low,then after specific delay
the function will put CHIP_EN high then RESET_N high.
reset-gpio is however defined as active low , causing this function
to hold the wifi module in reset.
Signed-off-by: Andreas Ålgård <aal@ixys.no>
When CAN is used, HSFLL frequency must >= AUXPLL frequency. Make sure to
send a request to the HSFLL clock instance.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
