* Disable handwritten check so we can override from board defs
* Shrink HEAP for netcpu so it fits.
* Disable netcpu logging so it doesn't conflict with appcpu.
Add comment to DTS file about SRAM partitions similar to the RTXXX
series has comments.
Add also a doc section to the frdm_rw612 about this.
Also fix the section hierarchy of the frdm_rw612 doc, the header levels
were wrong since the wifi and bluetooth, and reference sections were
under the debugging section.
Group all the wireless connectivity info together.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add support for the Antmicro's Myra SiP Baseboard. The board uses
Antmicro's Myra SiP which integrates STM32G491XX MCU and its SoC
configuration.
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
P1.7 used for led 0 was not passing gpio_api_1pin test (probably
shortened with another pin in the test setup. Use different pin
that passes the gpio_api_1pin test. At current stage this PDK is
'virtual' so this pin is not attached to any LED and it can be
changed.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Added a support for new mps2 board an386 to enable testing with ARM FVP.
Qualifier to build/run application with board is mps2/an386.
Signed-off-by: Samuel Chee <samche01@arm.com>
Add support PWM eMIOS for s32z2xxdc2 board. There is no LED
on-board dedicated for PWM, so no sample is supported. Only
enabling some pwm tests
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Removing period, duty and polarity configuration from
channel devicetree. At boot time, only minimal setup like
pinctrl, prescaler, etc should be initialized. PWM signal
is produced by using pwm_set* API
Also after this change, PWM period, duty are changed at the
next counter period boundary
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Since the ospi@ node does not exist anymore for the stm32u5 device
there is no more need for this pre_dt_board.cmake file.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
On the nucleo_g071rb , nucleo_g070rb and nucleo_g0b1re boards,
the CN7 MORPHO_L_9 to 11 pin are not correctly defined
in the st_morpho_connector.dtsi. This PR is fixing this.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit removes all references to the `xtools` toolchain variant in the
board YAML files.
Note that the `xtools` toolchain variant has been deprecated since Zephyr
v3.3.0 and now removed.
The removal process was automated using the following command line:
git grep -l xtools -- boards/*.{yml,yaml} | \
xargs -n 1 -P $(nproc) \
yq -i 'del(.toolchain[] | select(. == "xtools"))'
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Segger started to support MAX78002 with JLink version V8.12. So,
MAX78002EVKIT board has JLink support.
Signed-off-by: Furkan Akkiz <hasanfurkan.akkiz@analog.com>
nrf54l20pdk and nrf54l09pdk must use 64 MHz for now. So far it was
done by using SOC_NRF54LX_SKIP_CLOCK_CONFIG Kconfig option which was
skipping oscillator configuration so that it was running the default
frequency (which is 64 MHz). This approach was a bit cryptic because
DT was indicating that CPU was running 128 MHz when actual frequency
was different (and it was relying on assumption that default frequency
is 64 MHz).
After adding hfpll as clock source for CPU Kconfig option can
be replaced with DT setting where actual frequency is correctly
indicated. Since hfpll is a clock source for fast peripherals (e.g.
TIMER00) it is possible to have single source of information
regarding frequency.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Do not delete clocks for the bsim target. Clocks are referenced
by peripherals and it can be used to get frequency that clocks
the peripheral.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add a DTS binding for the MediaTek Audio Front End device, and
definitions for the in-tree devices.
These .dts files were auto-generated from pre-existing SOF code (that
defined the devices as C structs) using a tool currently being
submitted in the SOF tree, thus are included here as separate files.
The expectation is that future variants will be authored in this
format directly. Longer term we can move them directly into the core
board DTS.
Signed-off-by: Andy Ross <andyross@google.com>
10/100 ENET and gigabit ENET1G are supported on the EVKB revision.
Correcting the Supported Features table.
Signed-off-by: Derek Snell <derek.snell@nxp.com>
Change the property names in the bindings and DTS
to use hyphens(-) for separation instead of underscores(_).
Signed-off-by: James Roy <rruuaanng@outlook.com>
This commit adds multicore support for MCXN947.
It enables the secondary core CPU1 to boot from flash.
Signed-off-by: Tomas Galbicka <tomas.galbicka@nxp.com>
Enabling `CONFIG_INPUT_FT5336_INTERRUPT` if the ft5336 node in DT
has `int-gpios` property.
As a result of this change, some boards can eliminate lines that
explicitly configure `CONFIG_INPUT_FT5336_INTERRUPT`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
The CH32V003 belongs to the CH32V0 series. To improve code organization
and maintainability, all related files should be grouped together in a
dedicated subdirectory.
Signed-off-by: Jianxiong Gu <jianxiong.gu@outlook.com>
Unify property names in bindings and overlay, using
hyphens (-) instead of underscores (_) as separators.
Signed-off-by: James Roy <rruuaanng@outlook.com>
Add the PWM LED to Nucleo-WB07CC board and mark as compatible with PWM.
Also mark counters as supported (but don't enable by default).
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add the PWM LED to Nucleo-WB05KZ board and mark as compatible with PWM.
Also mark counters as supported (but don't enable by default).
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add the PWM LED to Nucleo-WB09KE board and mark as compatible with PWM.
Also mark counters as supported (but don't enable by default).
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
