Convert the eDMA compat to prop version for NXP S32Z2 SoC
that was missed in commit b070da7c33.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Since the label property from base.yaml is no longer deprecated, no need
to require to explicitly block it.
The only affected bindings seem to be these test bindings.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Label property is described in DT spec and does not need to be
deprecated in base.yaml anymore. It was originally deprecated to
discourage what was previously the most common use case of labels in
zephyr which was the old device_get_binding, which was rightfully
removed. However, labels do have a purpose as described in DT spec of
providing a human readable string to software to describe the device,
which there is some use for.
The description of a label should be given in the device binding, as
stated in DT spec.
Label properties should be of type string.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add devicetree node for code RAM, code RAM can be accessed
over AIXM bus or AXIF bus. Code access via AXIF interface
provides the best optimal performance
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Add `idle` and `s2ram` power states for nRF54H20 cpuapp and cpurad.
Also the substate `idle_cache_disable` added.
Signed-off-by: Adam Kondraciuk <adam.kondraciuk@nordicsemi.no>
Introduce etrbuffer in the tddconf bindings to support flexible
placement in the memory map.
Signed-off-by: Karsten Koenig <karsten.koenig@nordicsemi.no>
This commit adds the pfic interrupt controller driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the usart driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the systick driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the clock driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the pinctrl driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the dtsi and bindings for the WCH CH32V003 which is a
32-bit general-purpose RISC-V MCU.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
- Add SPI driver support for RA
- RA2A1 not support slave select keeping level so disable it
in Kconfig
Signed-off-by: Tri Nguyen <tri.nguyen.wj@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Use a string for the mipi-mode property over an integer value, as this
significantly improves the readability of the MIPI DBI device binding.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The NXP LCDIC peripheral contains two internal timers, with configurable
periods. These times are used to determine delays within the peripheral,
such as the reset and tearing enable signal delays. Allow these periods
to be set within the devicetree for the peripheral.
Raise the period where required for display drivers that need a value
other than the reset setting
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Extend tca954x (tca9546a, tca9548a) driver to support tca9544a i2c MUX.
(different bitmask and flag for enable bit in register)
Signed-off-by: Florian Weber <Florian.Weber@live.de>
The NXP PORT pinmuxing peripheral is reused across the MCX, S32, and
Kinetis lines. Rename the compatible from the family-specific
nxp,kinetis-pinctrl to a more generic nxp,port-pinctrl to reflect the
actual name for the IP block used within reference manuals.
Update the NXP HAL revision to include a change to use the new Kconfig
name for the PORT pinctrl driver
Update the MAINTAINERS.yml path, as there are no longer any NXP drivers
matching the string "drivers/*/*kinetis*
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
* Replace copies of fixed-partitions nodes in related boards by
referencing the apropriate partition table from the available list.
* For better reference the `partitions_*.dtsi` file has boot offset,
purpose and the flash size encoded in the file name. Default flash size
is considered to be 4MB.
* Added the flash size node for the boards which are not based on the
module.
* Removed flash size registry from the esp32.*common.dtsi
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Split and fix the total SRAM size for STM32L4Px/L4Qx/L4Rx/L4Sx
device. Those MCUs with up to 640 Kbytes SRAM:
This is 640KB for the STM32L4Rxxx and STM32L4Sxxx devices :
• 192 Kbytes SRAM1 + 64 Kbytes SRAM2 + 384 Kbytes SRAM3
This is 320KB for the STM32L4P5xx and STM32L4Q5xx devices :
• 128 Kbytes SRAM1 + 64 Kbytes SRAM2 + 128 Kbytes SRAM3
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Split and fix the total SRAM size for STM32L47x/L48x/L49x/L4Ax
device. Those MCUs with up to 320 Kbytes SRAM:
• 96 Kbytes SRAM1 and 32 Kbyte SRAM2 on STM32L47x/L48x.
• 256 Kbyte SRAM1 and 64 Kbyte SRAM2 on STM32L49x/L4Ax
The sram0 node at address 0x20000000 and sram1 at address 0x10000000
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace the DT_INST_PROP_OR statements with defaults
in the devicetree binding of the iCE40.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
These two new ICs are variants of the nRF54L15 with different memory
sizes:
- nRF54L05: 500KB RRAM, 96KB RAM
- nRF54L10: 1022KB RRAM, 192KB RAM
- nRF54L15: 1524KB RRAM, 256KB RAM
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Removing direct #define usage in the DTSI file and converting these
definitions to use a dt-bindings header instead.
Relocates the RPI_PICO_DEFAULT_IRQ_PRIORITY definition to a DTSI file and
introduces an override.dtsi file. The override file is used when no other
override file is present, allowing for better flexibility and compliance
with Zephyr’s DTS structure.
Fixes: #79719
Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io>
Add `hifive_unmatched//s7` (earlier selected by default, using
`hifive_unmatched`) and `hifive_unmatched//u74` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Add `hifive_unleashed//e51` (earlier selected by default, using
`hifive_unleashed`) and `hifive_unleashed//u54` targets.
Define work-area for other 4 cores in openocd.cfg
Update twister platform white/black lists, to support new targets
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Remove the renesas,ra-clock-generation-circuit driver, which is no longer
needed after migrating to the FSP-based implementation.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Remove the renesas,ra-pinctrl driver, which is no longer
needed after migrating to the FSP-based implementation.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add a common part for AMD board ACP_6_0_ADSP.
Add support for ACP_6_0_ADSP BOARD,
which represents ACP_6_0 soc.
This has a 1 Xtensa HiFi5 core, with 200-800MHz
1.75 MB HP SRAM / 512 KB IRAM/DRAM,
1 x SP (I2S, PCM), 1 x BT (I2S, PCM), 1 x HS(I2S, PCM), DMIC as
audio interfaces.
Signed-off-by: DineshKumar Kalva <DineshKumar.Kalva@amd.com>
A few bindings in the timer directory (for kernel timing sources) were
being used for counters (which can have alarms set, and have a distinct
API). Move these bindings to the counters directory.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added a binding description for the PPIB peripheral and added the device
tree nodes of the PPIB instances to the nRF54L15 and nRF54L20.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Convert the numerous revision compatibles to a DT property for the
revision called nxp,version (inspired from a linux DT property from
st called st,version on their DMA).
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This moves the SRAM definitions for STM32H56/7x chips up to the top
level since they are common to all of them.
Signed-off-by: Djordje Nedic <nedic.djordje2@gmail.com>
- stm32cO11/31 share the same spi peripheral
- include stm32_dma header to be able to configure
spi with dma config macros (STM32_DMA_PERIPH_TX,...)
in dts
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
The Xilinx AXI DMA Controller is commonly used in FPGA designs.
For example, it is a part of the 1G/2.5G AXI Ethernet subsystem.
This patch adds a driver for the Xilinx AXI DMA that supports
single MM2S and S2MM channels as well as the control and status
streams used by the AXI Ethernet subsystem.
Signed-off-by: Eric Ackermann <eric.ackermann@cispa.de>
This commit changes the way some x86 devicetree set the unit-address values
of memory nodes. Before the change, they were always set to `0`. After the
change, they are derived from the `DT_DRAM_BASE` macro to match the first
address specified by the reg property.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
some flashes support special opcodes
for 4-byte addressing, that can be used
without switching to 4-byte mode.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Alder Lake have at least 2 cores. Both boards using this SoC
(up_squared_pro_7000 and adl) are configured with
MP_MAX_NUM_CPUS=2, so dts should contain at least one more core.
Signed-off-by: Franciszek Pindel <fpindel@antmicro.com>
Implement a new stable-poll-period-ms property to specify a new (slower)
polling rate for when the matrix is stable.
The keyboard thread can eat up a surprisingly high amount of cpu cycles in
busy waiting if the specific hardware implementation happen to have a
particularly slow settle time, but high frequency polling is really only
needed when debouncing.
The new property allow slowing down the polling rate when the matrix is
stable (either key pressed but none to be debounced or idle in the case
of the gpio implementation with no interrupts), this allows reducing the
overall cpu time taken by the keyboard scanning thread when keys are
persistently pressed.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The it8xxx2_kbd KSO pins can be used as both keyboard scan and GPIO. By
default the keyboard scanning driver controls the output level of all
the KSO signals from 0 to (col-size - 1), meaning that any line in
between used as GPIO is going to have its output value overridden.
Add a kso-ignore-mask property to the keyboard scan driver to allow
specifiying extra pins that should not be controlled by the driver.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This follows update of UTCPD.VBSCALE register field. It supports:
- "divide-20": External VBUS voltage divider circuit should be 1/20
for EPR application. The divided voltage compares with
200mV to set or clean VBUS Present bit.
- "divide-10": External VBUS voltage divider circuit should be 1/10
for SPR application. The divided voltage compares with
400mV to set or clean VBUS Present bit.
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
Add a driver for the MB85RSM1T FRAM chip.
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The HAL configuration binding can be done dynamically based on the
IP's address space. The `hal-cfg-index` property is more tied to
software rather than hardware so remove it as an attempt to clean
up the binding.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add USB node to apollo4p and apollo4p_blue qualifier, and apollo4p_evb
and apollo4p_blue_kxr_evb board to enableUSB support on the MCU and
its EVB.
Signed-off-by: Chew Zeh Yang <zeon.chew@ambiq.com>
Add npcm miscellaneous device control and power and clock control
instances.
Add device tree bindings for npcm power and clock control.
Signed-off-by: Alan Yang <tyang1@nuvoton.com>
Add initial support of the mailbox driver based
on the inter VM shared memory mechanism similar
as the existing IPM driver.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
With this change, the LPTIM counter will be able to set
its timeout to the st,timeout value. So that system can
sleep for that period without interruption.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace the enum for load modes for the iCE40 with a boolean flag,
as there are only two options:
- SPI: default, which should be used whenever possible
- GPIO bitbang: workarorund, in case a low-end microcontroller is used
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This will help distinguish 64 and 32-bit platforms by tooling, following
the pattern visible in e.g. RISC-V.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
Those dtsi are a base for a range of 32-bit platforms. Setting this
compatible makes it easier to distinguish all 32-bit x86 platforms.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
y
atom.dtsi enforces "intel,x86", but it doesn't help us discern if the
platform is 32 or 64-bit. We do that for example in RISC-V and it's
useful from the tooling perspective.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
This commit introduces the L2 Memory Capabilities (hsbcap) register node
to the Devicetree specifications for Intel ADSP ACE platforms. The
hsbcap register provides information on the general capabilities
associated with the L2 memory, which is critical for system
configuration and resource management. The hsbcap node has been added to
the Devicetree source files for ACE 1.5 (MTPM), ACE 2.0 (LNL), and ACE
3.0 (PTL) platforms.
In addition, the DFL2MM_REG macro in adsp_memory.h has been updated to
use the Devicetree node label for hsbcap, ensuring a consistent and
maintainable approach to accessing this register across the codebase.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
-Update formatting and contents of index.rst for cy8ckit_062s4
-Update formatting and contents of index.rst for cy8ckit_064s0s2_4343w
-Update formatting and contents of index.rst for cy8cproto_062_4343w
-Update formatting and contents of index.rst for cy8cproto_063_ble
-Update formatting and contents of index.rst for xmc45_relax_kit
-Update formatting and contents of index.rst for xmc47_relax_kit
-Change all instances of "PSoC" to "PSOC" for infineon platforms
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
Align the shared memories with the memory.h layout.
Reorder nodes to show memory related nodes together.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
This bus type was originally created for what's today the ipc.c HCI driver.
Since this type hasn't yet been synced with BlueZ, rename it for
consistency, however leave the old define to not break backwards
compatibility with existing DT bindings (there are several more that use
"ipm" than ipc.c).
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
The authoritative source of these values is BlueZ:
https://git.kernel.org/pub/scm/bluetooth/bluez.git/tree/lib/hci.h#n38
Update our values with the above. The IPM definiton doesn't exist in
BlueZ, but should be added there to make sure we don't get out of sync
again.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Remove CONFIG_MMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the mmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
mmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_SDMMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the sdmmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
sdmmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The new update of clock device tree make the pll p q r clock
source cannot be choose by other node
This fix add 1 new dts binding for pll out p q r out line
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Define the "clocks" property, for the flash "st,stm32h7-flash-controller"
node, only for the stm32H7 dual-core devices
which have the RCC bit 8 present in their RCC AHB3 register.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the global power domain entry. This domain is not memory-mapped
but controlled using NRFS services.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This commit adjusts the sizes of the two PLIC nodes AE350 defines:
* `plic0` size is changed from `0x04000000` to `0x02000000`
* `plic_sw` size is changed from `0x04000000` to `0x00400000`
Without these change, `plic0` address space would overlap with `plic_sw`,
and with other memory-mapped peripherals.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The nrf7000, nrf7001 and nrf7002 expose a coex hardware interface
which is independent from the wifi/control interface (spi and
control pins)
These interfaces where previously combined into a single model. This
is incompatible with the actual usage of the interfaces where one
core may interact only with the coex interface, and another with the
wifi/control interface.
This commit moves the coex interface, commonly described in
"nordic,nrf70-coex.yaml", out of the wifi/control models
"nrf700<variant>-<bus>.yaml" to its own models
"nrf700<variant>-coex.yaml"
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
- Modify the macro in source code AGT to get the right data from
device tree
- Modify name of agt node
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Extended UICR will not be used as its configurations will be merged
with the UICR registers in NVR.
Memory maps changes are needed to align with pre compiled
firmware.
Signed-off-by: Håkon Amundsen <haakon.amundsen@nordicsemi.no>
Signed-off-by: Jonathan Nilsen <jonathan.nilsen@nordicsemi.no>
This commit fixes minor copyright issues and corrects the compatible of
gpio-stepper with the vendor name as zephyr
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Added NXP IRTC Driver support and binding.
This driver is expected for users needing
Time Date info in their application.
The driver additionally has an alarm mode that
can be enabled to fire an intterupt when the time
and alarm values match.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
These properties should eventually be removed from this binding as they
have been introduced to control soc specific clock trees and don't
correlate to anything in the IP, but for now just make them not required
and remove them from DT for SOCs that don't even use them.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Remove the "required: true" attribute from the STM32 DMAMUX binding.
This is required for STM32WB0 series where the DMAMUX has no interrupt line
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
PR #79683 missed a few nodes introduced while it was under review.
Replace the remaining raw values with STM32_CLOCK in WB0 DTSI files.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Only initialize the HFXO Manager HAL driver if the HFXO is enabled in
DeviceTree, the device uses SYSRTC for timekeeping, and Power Manager
is enabled. HFXO Manager integrates with the Sleeptimer HAL driver for
SYSRTC to autonomously wake the HFXO prior to Sleeptimer wakeup from
deep sleep. It is not needed on devices that don't have HFXO-SYSRTC
integration, and it is not needed if the application doesn't use deep
sleep.
Add missing call to init_hardware() prior to init().
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Additional IO ports (6,7 and 8) are availble on the r7fa6m4af3cfb
variant of the RA6M4 Microcontroller.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
The CSI is an NXP IP and the driver has been very much changed
by NXP, so add NXP copyright to it.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "source_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Instead of fixing csi2rx clock frequencies, set them according to the
pixel rate got from the camera sensor.
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "sensor_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
USB configuration is missing in Devicetree for NXP MCX C series.
Add the configuration to common and SoC specific dtsi file.
Delete usb node for SoCs without USB support.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Some NXP SoC's do not have USB voltage regulator present.
Add property to indicate it. Negative logic is used, because
the regulator is present in great majority of SoC's, and thus the new
property can be added only for SoC's without the regulator.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Add stm32h7 ethernet compatible "st,stm32h7-ethernet",
used also for stm32h5.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
The DT node "stimer0" represented two different hardware timers,
RTCC and SYSRTC. Use the correct peripheral names for the nodes.
Add interrupt names and missing interrupt numbers.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Documents cirrus,hw-i2c-lock property in the devicetree bindings. This
flag indicates that the control port write-lock was enabled in hardware
via the PGPIO2 pin.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Add a pinctrl driver for Microchip MEC5 HAL based chips.
The driver removes the YAML enum "no change" property
value from the driver strength and slew rate properties.
Update the shared header file in mec soc common folder to
use a different Z_PINCTRL_STATE_PINCFG_INIT for MEC5.
Modifications to legacy MEC172x XEC PINCTRL will be in
a future PR.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Die temperature measurement is not configured in devicetree
for NXP MCX C series.
Add die temperature measurement configuration.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
The nRF54 and nRF92 chips has data cache, which means
the ICMsg and ICBMsg must be configured to follow required
cache alignment of the shared memory.
The `dcache-alignement` needs to be defined for that.
Signed-off-by: Dominik Kilian <Dominik.Kilian@nordicsemi.no>
Renamed andestech,plic-sw to andestech,mbox-plic-sw because the mbox node
is based on the PLIC interrupt controller node instead using the plic
hardware directly.
Signed-off-by: Jimmy Zheng <jimmyzhe@andestech.com>
The plic-sw is the same hardware as the plic interrupt contoller and should
be used with intc_plic driver instead of separate mbox driver.
Renamed plic-sw node from "mbox: mbox-controller@e6400000" to
"plic_sw: interrupt-controller@e6400000".
Signed-off-by: Jimmy Zheng <jimmyzhe@andestech.com>
The ILPS22QS is an ultra-compact piezoresistive absolute pressure sensor
which functions as a digital output barometer, supporting dual full-scale
up to user- selectable 4060 hPa. The device delivers ultra-low pressure
noise with very low power consumption and operates over an extended
temperature range from -40 °C to +105 °C.
(https://www.st.com/en/mems-and-sensors/ilps22qs.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Rename the Silabs HCI driver to hci_silabs_efr32.c to better indicate what
hardware it supports. Also rename the associated devicetree binding and
Kconfig options to be consistent with the new driver name.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Add initial SoC support for the TI J721E SoC series Cortex-R5 core.
TRM for J721e https://www.ti.com/lit/zip/spruil1
File: spruil1c.pdf
Signed-off-by: Prashanth S <slpp95prashanth@yahoo.com>
Signed-off-by: Andrew Davis <afd@ti.com>
Some instances of the FLEXSPI IP permit limiting AHB bus access so that
no memory access requests will straddle a page boundary. Add a property
to manage this setting.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Updated ADXL345 driver with RTIO stream functionality.
Added Trigger intterupt functionality. RTIO stream is using
FIFO threshold.Together with RTIO stream, RTIO async read
is also implemented.
Signed-off-by: Dimitrije Lilic <dimitrije.lilic@orioninc.com>
Timer driver using Microchip 32KHz based RTOS timer as the kernel
timer tick. The driver uses one of the 32-bit basic timers to
support the kernel's k_busy_wait API which is passed a wait
count in 1 us units. The 32-bit basic timer is selected by using
device tree chosen rtimer-busy-wait-timer set to the handle
of the desired 32-bit basic timer. If this driver is disabled,
the build system will select the ARM Cortex-M4 SysTick as the
kernel timer tick driver. The user should specify RTOS timer
as kernel tick by adding the compatible properity and setting
the status property to "okay" at the board or application level
device tree. The driver implements two internal API's for use
by the SoC PM. These two API's allow the SoC PM layer to disable
the timer used for k_busy_wait so the PLL can be disabled in
deep sleep. We used a custom API so we can disable this timer
in the deep sleep path when we know k_busy_wait will not be
called by other drivers or applications.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Introduce bindings for Series 2 oscillators: HFRCODPLL, HFRCOEM23,
LFRCO and LFXO.
Add clock tree representation in devicetree `clocks` node.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Switch EFR32MG21 to use the device init HAL. This makes the init sequence
the same as the rest of Series 2.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
The DC-DC converter was unconditionally initialized with default
settings on Series 2. Add device tree binding and nodes, and guard
call to init function. Map DT options to config header from HAL.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Add wsen_hids_2525020210002 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Add support for Bosch bmp390 sensor, the drop in replacement for the
bmp388 with same register but different chip-id. This patch make use
of "bosch_bmp390" or "bosch_bmp388" and set the specific chip-id in a
data->chip-id variable, which then used to check against the register
value.
Additional, manual shift operation had been replaced with ENDIAN safe
macros and calibration values with target variable of int16_t add a
cast for it.
bmp388_spi: read register implementation wrong, fixed it.
tx-buffer must be <addr><dummy><dummy> in order to receive the
register value. Read registers in burst mode and have rx and tx
buffer same spi_buf to avoid clock stop and delay with nrf5.
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
The NTC thermistor implementation assumes a constant pull-up voltage
and that the ADC channel is measured against a reference voltage so that
the absolute voltage across the NTC can be calculated. Based on the
relationship of `pullup-uv` and this absolute NTC voltage, the resistance
of the NTC is calculated.
There are applications where the "pullup-uv" is not constant, but VDD.
Most ADCs support relative measurements against VDD. If `pullup-uv` is not
defined, the implementation assumes now that the ADC channel is configured
to use VDD as a reference and therefore no millivolt conversion is
required.
Signed-off-by: Stefan Schwendeler <Stefan.Schwendeler@husqvarnagroup.com>
Added a new driver to support SPI communication via EUSART. Since the
Silabs EFR32MG24 family SoCs have only one USART, EUSART support is
necessary for implementing SPI functionality.
Signed-off-by: Teresa Zepeda Ventura <teresa.zvent@gmail.com>
- boards: renesas: Add support for agt.
- drivers: counter: Add support for counter driver use agt
- dts: arm: Add support for agt.
- dts: bindings: Add support for agt counter driver.
- soc: renesas: Add support for agt counter driver.
- samples: drivers: counter: alarm: Add support for RA8
This is initial support with only basic functionality for counter
operation on Zephyr using AGT hardware, current support for
count source is limited to LOCO and PCLKB, other count source
like underflow signal external pin or AGTIO from another AGT
channel will be added in later support
Signed-off-by: Ha Nguyen <ha.nguyen.fz@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
support the configurations which apply for LVDS pads
+ termination resistor
+ current reference control
+ rx current boost
Signed-off-by: Tu Nguyen Van <tu.nguyenvan@nxp.com>
The production version of the nRF54L15 SoC is now available, so remove
the initial Engineering A (EngA) preview version.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some devices may belong to >1 power domain, so with the current design
this is something not possible to describe. It's worth to note that
Linux also uses the `power-domains` naming scheme, not `power-domain`.
This patch also introduces `power-domain-names` so that each entry in
`power-domains` can be given a name if needed. `#power-domain-cells`
is now required as well.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Enable the irqstr interrupt controller for the adsp-based
imx8mp.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Add 1-Wire register file
Some MAX32 MCUs has 1-Wire peripheral some one not
So that added in device related dtsi file.
Has 1-W Not have 1-W
MAX32655 MAX32662
MAX32666 MAX32670
MAX32680 MAX32672
MAX32690 MAX32675
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Initial support for SSD1322 OLED display driver. Only 1 bit color mode is
supported.
Most options map directly to values documented in the datasheet,
except segments-per-pixel, which I had to add to support the Newhaven
NHD-2.7-12864WDW3. This is a slightly odd feature, but in practice
it is a lot nicer to support it in the driver, and since we're currently
remapping pixels anyway, it makes sense to implement here.
This driver also has a configurable buffer size for the pixel conversion.
By using a larger buffer, we can potentially use DMA for the SPI transfer.
The default is set to 8, which is the smallest value that supports
segments-per-pixel = 2
Initial driver implementation by Lukasz Hawrylko <lukasz@hawrylko.pl>.
Additional options and configurability by Tobias Pisani <mail@topisani.dev>
Signed-off-by: Lukasz Hawrylko <lukasz@hawrylko.pl>
Signed-off-by: Tobias Pisani <mail@topisani.dev>
Co-authored-by: Lukasz Hawrylko <lukasz@hawrylko.pl>
Co-authored-by: Tobias Pisani <mail@topisani.dev>
Current nPM1300 charger driver does not work with batteries
without NTC thermistor. Added supported for this feature.
Signed-off-by: Javier Santos <jasr93@outlook.es>
This commit adds support for INA236 into the existing INA230 driver.
These two chips are similar enough to share most of the code.
The device can be defined the same way as INA230 and we only have
the extra option to select the high-precision mode.
```
ina236: ina236@40 {
status = "okay";
compatible = "ti,ina236", "ti,ina230";
reg = <0x40>;
adc-mode = "Bus and shunt voltage continuous";
vbus-conversion-time-us = <1100>;
vshunt-conversion-time-us = <1100>;
avg-count = <1>;
current-lsb-microamps = <1000>;
rshunt-micro-ohms = <15000>;
alert-gpios = <&gpiod 0 GPIO_ACTIVE_LOW>;
high-precision;
};
```
Signed-off-by: Tomáš Juřena <jurenatomas@gmail.com>
Enforce some minimum delay between enabling the voltage divider with a
GPIO and sampling the analog voltage. Without this delay the ADC can
easily sample the transient power up curve instead of the steady state
output.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Implement the parallel mode in the powertrain switch TLE9104.
This allows that OUT1 and OUT2 are controlled together, as well
as OUT3 and OUT4.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
It's more common (and more readable) convention to use lower-case
names for string-based device tree property values. Convert the HCI bus
and quirks to follow this convention. Also take advantage of the
recently added support for string-array enums to enforce that the
correct values are used.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Add I2C and SPI Device Tree nodes in SoC DTSI files to allow usage of these
peripherals.
Note that the SPI driver requires no modification to be functional on WB0.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
As per USB 2.0 specification 7.1.5.1: The voltage source on the pull-up
resistor must be derived from or controlled by the power supplied on the
USB cable such that when VBUS is removed, the pull-up resistor does not
supply current on the data line to which it is attached.
Signed-off-by: Lukas Gehreke <lk.gehreke@gmail.com>
Add a DTS binding file for Telit ME310G1 cellular modem based
on the binding for ME910G1 but without the mdm-reset-gpios as
the ME310 doesn't have a reset input.
Signed-off-by: Niklas Gürtler <niklas.guertler@e-obs.de>
Add a no-disconnect property that skips the call to disconnect the pin
during suspend, this is useful as not all gpio controllers supports pin
disconnection, and right now using the gpio-keys driver on one of those
results in a failed initialization if PM runtime is enabled.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Last 1k is used for saving VPR context and shall not be exposed.
Limiting RAM to 511k.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Split header files containing symbols denoting SAADC inputs
so that only supported inputs can be used for given device.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Add initial Feature Unit bindings allowing user to place the Feature
Unit inside UAC2 instance description. Currently the bindings facilitate
only specifying which controls are available on the Primary channel 0
and on each Logical channel. The number of Logical channels has to be
derived from data-source property.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Test the new c-macros for dt enums. The new macros are already used in
the existing macros. As an example, DT_ENUM_IDX(node_id, prop) uses
DT_ENUM_IDX_BY_IDX(node_id, prop, 0) to get its result. However, this is
insufficient for testing the complete functionality of these macros.
Therefore, additional tests are added to make sure they work
appropriately for other indices besides 0.
Signed-off-by: Joel Hirsbrunner <jhirsbrunner@baumer.com>
This concerns both `nordic,owned-memory` and `nordic,owned-partitions`.
Introduce a property named `nordic,access`, which is meant to replace
the `owner-id` and `perm-*` properties. It allows for describing how
multiple domains should access a single memory region, possibly with
different permissions per owner, but without having to create more than
one DT node for this purpose.
This change is also motivated by updated memory protection requirements
on the nRF54H20, which mandate that a given memory region must only be
reserved by one domain, even if multiple domains can have access to it.
This restriction is now described in the binding itself.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Add SMARTDMA video driver. This driver uses the SMARTDMA engine as a
parallel camera interface, which can read QVGA frames from a camera
device. Due to SRAM constraints, the video driver divides the camera
stream into multiple horizontal video buffers as it streams them back to
an application.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The SMARTDMA is a programmable DMA engine, and supports custom firmware
in order to run complex DMA operations. Update the driver to increase
the flexibility users have when configuring the SMARTDMA with
custom firmware, and remove the RT500 display firmware specific
definitions and functionality from the driver.
This display setup is now handled from the MIPI DSI driver, since the
firmware used for this case is specific to the MIPI DSI IP.
This change also requires an update to the RT500 devicetree, as the
register definition for the SMARTDMA has changed, so the base address
must as well.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
TI tmp1075 driver implemented based on tmp108 driver.
The driver initializes the sensor based on the DTS.
Added tmp1075 example overlay file to thermometer sample.
All you need to do to use the sensor is to connect the I2C and
optionally interrupt line.
To see default DTS configuration option inspect `ti,tmp1075.yaml`
bindings file and sensor spec.
Signed-off-by: Paweł Czaplewski <pawel.czaplewski@arrow.com>
Reduce the valid scaling range for the gain multipliers and dividers to
provide more headroom on int64_t overflows in the calculations. Take
advantage of this headroom to perform all multiplications before
divisions.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Change the unit of the sense resistor in the devicetree binding from
micro-ohms to milli-ohms. This is done for three reasons.
Firstly, the maximum value resistor that can currently be represented
is 4.2 kOhms, due to the limitation of devicetree properties to 32 bits.
Secondly, storing the resistance at such a high resolution makes
overflows much more likely when the desired output unit is micro-amps,
not milli-amps.
Finally, micro-ohms, are an unnecessarily precise unit for the purpose
of these calculations, and a resolution that is not realistic to
achieve. The high resistor resolution results in large divisors that
reduce the resolution of outputs. Unlike resistors characterised down to
the micro-ohm, devices wanting to measure micro-amps are actually
realistic.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add common video interface binding. This binding contains the most
common properties needed to configure an endpoint subnode for data
exchange with other device.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The stm32l4 devices were previously assigned the generic STM32 AES driver,
which turned out to be incompatible with the stm32l4 series. This commit
updates the nodes to use the new driver specifically designed for this
series.
Add missing node for stm32l4a6, stm32l4q5, stm32l4s5 and stm32l486 socs.
It appears stm32l4p5 and stm32l496 socs do not have the AES accelerator
present, so the nodes are removed from the dts files.
Signed-off-by: Lucas Dietrich <ld.adecy@gmail.com>
This patch completes the addition of support for the STM32L4 AES
accelerator by introducing conditional handling for different STM32 AES
HAL variants. Key changes include:
- Created device tree bindings `st,stm32l4-aes` for STM32L4 AES
- Replaced `copy_reverse_words` with `copy_words_adjust_endianness`
to handle endianness conversion for different variants.
Signed-off-by: Lucas Dietrich <ld.adecy@gmail.com>
NPCX9 and former chips defines two kinds of sub-power-states to support:
1. Standard wake-up time: if the chip needs to stay in the deep sleep
state more than 200 ms.
2. Instant wake-up time: if the chip needs to stay in the deep sleep
state less than 200 ms.
As NPCX4 can stay in the deep sleep state at more than 200 ms with the
instant wake-up capability, we can define only one sub-power state.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Update the devicetree binding for the nxp,kinetis-acmp comparator and
move the binding to dts/bindings/comparator.
The update to the binding includes:
- Remove unused io-channel-cells property
- Remove unused sensor-device include
- Adding missing properties dac config, discrete mode config, and
input configs.
- Rename properties to exclude redundant vendor prefix since props in
this binding are not inhereted, and as such, don't need to be
namespaced.
- Deprecate the old names of the renamed properties
The sensor based device driver has been updated to support both the
deprecated and new property names. This allows it to use both
nxp,enable-sample and filter-enable-sample for example.
Additionally, remove the unused io-channel-cells properties from
in-tree nodes of compatible = "nxp,kinetis-acmp"
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Adjust comparator nodes of nrf SoCs to exclude the unused
io-channel-cells property and simplify the comment describing how
to configure the comparator hardware block as COMP or LPCOMP for
SoCs which support this.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Counters configuration is missing in Devicetree for NXP MCX C series.
Add lptmr, rtc and pit configuration to Devicetree.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
If the `divider-int-0` or variations of these for each channel properties
are not specified, or if these is 0,
the driver dynamically configures the division ratio by specified cycles.
The driver will operate at the specified division ratio if a non-zero
value is specified for `divider-int-0`.
This is unchanged from previous behavior.
Please specify ``divider-int-0`` explicitly to make the same behavior as
before.
In addition, the default device tree properties related to the division
ratio have been removed.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
NXP mcxc series has boot source configured to ROM. ROM bootloader
waits 5 sec for active peripheral detection timeout before jumping
to application in flash which makes booting very slow.
Change configuration to boot from flash and allow boot source
selection by external pin.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
IAP is a reference to the method of software interaction with the flash
used in the current driver implementing support for this flash. The
DT compatible should not be named like this.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add a new `andestech,nceplic100` binding that inherits from the
`sifive,plic-1.0.0` binding. This is so that the Kconfig
`DT_HAS_ANDESTECH_NCEPLIC100_ENABLED` would be generated during
build.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
MAX14906 industrial 4 channel Input/Ouput GPIO expander with diagnostics.
Per channel diagnostics for open wire, over current.
Global diagnostic for power supply, communication and various fault
conditions.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
Move the process of replacing numerical values with macros to
the header, and set the division ratio in a numeric without
using macros in the device tree.
Change `clk-div` defined in `renesas,ra-cgc-pclk.yaml` to `div`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
DeviceTree typically references the clock source using the `clocks`
property defined in `base.yaml`, so we'll change it to this.
Also delete the custom clock source definitions in
`renesas,ra-cgc-pclk-block.yaml`, `renesas,ra-cgc-pclk.yaml`, and
`renesas,ra-cgc-pll.yaml`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Changes the path name of a DTS node so that it can be used
as the stem of a BSP macro.
All nodes to be changed are referenced via labels,
so only the name is changed.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Having the lowest possible interrupt priority is causing the
tests\arch\arm\arm_irq_zero_latency_levels test to fail.
This test reserves 2 priority levels for the low latency interrupts.
Since CYW20829 supports 3 interrupt bits, 6 becomes an invalid
value when 2 levels are reserved for the low latency interrupts.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Property "block-cycles" is required for node "zephyr,fstab,littlefs",
but source code did not get the value from dts file, now add it.
Additionally correct the wrong description of property "block-cycles"
in binding file.
Signed-off-by: Paul He <pawpawhe@gmail.com>
Update ADC bindings documentation to state that a domain clock is now
necessary if asynchronous clock is selected.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
For STM32L1, U5 and WBA, the ADC always uses an asynchronous clock source,
so we add the default clock source in the clock node.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Some IBI TIR packets can be larger than the ibi data fifo size
which can prevent it from receiving the full packet. This adds
a data struct in to the driver data where data can be pushed
to as data is being transfered.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Enable support for 8 bit 8080 mode in the NXP LCDIC driver. Support
for programming the minimum duration of the write active/inactive signal
is also added, since this will be required to support high display
clocks in 8080 mode.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add mailbox node used for inter-process communication.
For DSP, we have a direct interrupt line to the core.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Change the STM32 Temperature Sensor bindings to accept the average slope
value in string form instead of integer. With this change, it is possible
to use the raw decimal value found in each MCU's datasheet instead of
needing to scale it (differently depending on series!). This also allows
regrouping the property in a single file to reduce duplication.
Also update all DTSI files affected by this change and the dietemp driver
to accept the property's new format.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Improve the STM32 dietemp sensor bindings by rewording the descriptions
of bindings and properties.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Reduce duplication in STM32 dietemp bindings by regrouping the 'ntc'
property declared in both "st,stm32-temp" and "st,stm32c0-temp-cal"
to the shared "st,stm32-temp-common" binding.
"st,stm32-temp-cal" is also modified to block 'ntc' property on include as
no dual-calibration sensors to date require it (this could be changed later
when need arises).
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Set the 'avgslope' property of 'st,stm32c0-temp-cal' to required, and
remove its default value, to ensure new series cannot be introduced without
setting the property to the correct value explicitly.
This change does not require any DTSI modification, because there are only
two files using this compatible (stm32f030.dtsi / stm32c0.dtsi), and both
of these already set 'avgslope' explicitly.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Set the 'avgslope' property of 'st,stm32-temp' to required, and remove its
default value, to ensure new series cannot be introduced without setting
the property to the correct value explicitly.
This change does not require any DTSI modification, because there are only
two files using this compatible (stm32f1.dtsi / stm32f2.dtsi), and both of
these already set 'avgslope' explicitly.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Set the 'v25' property of 'st,stm32-temp' to required, and remove its
default value, to ensure new series cannot be introduced without setting
the property to the correct value explicitly.
This change does not require any DTSI modification, because there are only
two files using this compatible (stm32f1.dtsi / stm32f2.dtsi), and both of
these already set 'v25' explicitly.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
The typical value for V25 is different on the STM32F100 line compared
to other STM32F1 MCUs. Update the DTS property to the correct value.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add the missing 'avgslope' property to the DTSI for STM32F030/STM32F070.
This fixes improper results being returned by the driver: the correct
value for the average slope is 4.3mV/°C (4300 µV/°C), but the binding's
default value of 2.53mV/°C was used instead, since property was missing.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Remove the "Negative Temperature Coefficient" attribute from the STM32F2
die temperature sensor node, as it does not correspond to the hardware.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add virtual Cortex R8 SoC. This target does not represent a real SoC,
but can be easily run in Renode.
This will allow to easily test basic architecture support.
Signed-off-by: Krzysztof Sychla <ksychla@antmicro.com>
Signed-off-by: Marek Slowinski <mslowinski@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
Add the <requires-ulbpr> property from the "jedec,spi-nor-common.yaml"
to the existing st,stm32-qspi-nor.yaml. So that external quad-NOR with
unlock the Global Block Protection (BPR) (opcode 0x98) is accepted.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
- Driver always initializes the device in the suspended state
- If CONFIG_PM_DEVICE_RUNTIME=n, device PM callback will be called with
RESUME action, thus setting up pins to default state and enabling the
peripheral
NOTE: when CONFIG_PM_DEVICE=n, the pinctrl sleep state will not be
available (-ENOENT) and so never applied, thus avoiding a pin
suspended->active transition.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add nodes for LPTMR. This is sufficient to enable their use as counter
devices when set to status okay.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add DT node and clocking of TPM peripherals, which are used for PWM.
Also change the soc clock enable code to not use preprocessor
conditionals.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add peripheral bridge definitions to DT, this also fixes the base
address of the GPIO peripherals which were faulting in the driver due to
the wrong reg address.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The Multi-Channel Inter-Processor Mailbox (MBOX) framework can be seen
as a more general version of the Inter-Processor Mailbox (IPM) framework.
An MBOX driver provides for multiple channels, where IPM provides for
only a single channel of communication.
Currently many applications are written to use IPM, while some are now
being written to use MBOX. This means if a platform wants to support both
types of apps a given it must have a driver for both frameworks. As MBOX
is the newer and more generic framework, new drivers are being added for
this framework only and older IPM drivers are being migrated to MBOX.
This leads to the situation where applications need to be written twice,
once for each framework, to run across all platforms.
The solution is to add a gasket driver that exposes the IPM interface
while using a MBOX driver in the back-end. This shim driver allows
platforms to only need an MBOX driver to support both types of
application. This IPM driver can be used when an application only
supports IPM but the platform only supports MBOX.
This will allow platforms and applications to be ported over to MBOX
independently of each other. Add this driver here.
Signed-off-by: Andrew Davis <afd@ti.com>
- Added `cs-supported` property to nrf-radio devicetree
- Added `HAS_HW_NRF_RADIO_CS` Kconfig option which is set if
`cs-supported` property is enabled
- Enabled `cs-supported` property for nrf54-series devices
- Disabled `cs-supported` on nrf54l15bsim because it is not
yet supported
Signed-off-by: Ivan Iushkov <ivan.iushkov@nordicsemi.no>
For nrf54h20 a range of combinations exist to configure the test and
debug domains data sources and sinks. Expose them in DTS to allow
configuring them. Also drop the previous style which was too rigid to
extend to cover all cases cleanly. The old style was only used in a
single sample application so far.
Signed-off-by: Karsten Koenig <karsten.koenig@nordicsemi.no>
This fixes the following warning:
> unit address and first address in 'reg' (0x80280000) don't match for
> /soc/sckcr@81280004
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Change the interrupt number of flash in device tree due to duplication
And disable CONFIG_FLASH as default
Signed-off-by: Quy Tran <quy.tran.pz@renesas.com>
Renamed soc from ace30_ptl to ace30.
We were previously using the wrong soc name.
The correct name is ace30.
There is only one ptl platform, but there can be several ace30 platforms.
Signed-off-by: Grzegorz Bernat <grzegorzx.bernat@intel.com>
Add pwm yml file.
TIMER0/1/2/3 support pwm, LPTIMER0/1 not.
LPTIMER0/1 provide 16bits out that not meet pwm requirement.
Co-authored-by: Mert Vatansever <mert.vatansever@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Common uf2 partition configurations to avoid duplication in boards.
There appears to be a bit of confusion about exactly what a proper
UF2 partition map looks like for the nrf52840, so common dts
configurations should help to avoid confusion.
Configuration for SoftDevice v6 and v7 provided as thats what was
fouond in use in tree already.
Signed-off-by: Jacob Winther <jacob@9.nz>
Spi bus controller node names should follow recommended naming
convention from DT spec otherwise DTC will report a warning.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add property which indicates that UARTE support frame timeout
feature. Property is added to nrf54h20, nrf9280, nrf54l20 and
nrf54l15.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add support for VBUS measuring part of the TCPCI compliant device.
This device should be used as a child-node for the more specific
TCPC driver and referenced by the vbus property in the usb-c
connector node.
Signed-off-by: Michał Barnaś <barnas@google.com>
Introduce GPIO-based driver for MIPI DBI class that allows MIPI DBI
type A and B displays to be used on general platforms.
Since each data pin GPIO can be selected individually, the bus pins are
set in a loop, which has a significant negative impact on performance.
When using 8-bit mode and all the data GPIO pins are on the same port,
a look-up table is generated to set the whole port at once as a
performance optimization. This creates a ROM overhead of about 1 kiB.
Tested 8-bit 8080 mode with ILI9486 display on nRF52840-DK board.
Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
HFXO is represented as a child of the oscillators node. A new node is
created because it requires its own properties (see the binding for more
details).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
LFXO is represented as a child of the oscillators node. A new node is
created because it requires its own properties (see the binding for more
details).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
- Create a new compatible: nordic,nrf53x-oscillators, as other series,
e.g. nRF54LX contain a similar but different IP (with PLL control,
etc.)
- Adjust DT: use recommended node name, remove redundant status okay.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Register all the lpi2c instances.
Add no-power-level property and update driver
to adapt no-power-level property.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
This defines raspberrypi,pico-xosc along with a configurable startup
delay multiplier. On some boards, the XOSC takes longer to stabilize.
Signed-off-by: Xudong Zheng <7pkvm5aw@slicealias.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x1002c0) don't match for
> /soc/dma@100200
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x3fc70) don't match for
> /soc/peripheral@40000000/flash-controller@34000/flash@9fc70
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warnings:
> unit address and first address in 'reg' (0x40094000) don't match for
> /soc/peripheral@40000000/usbhs@144000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x3fc70) don't match for
> /soc/peripheral@40000000/flash-controller@34000/flash@9fc70
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warnings:
> unit address and first address in 'reg' (0x40094000) don't match for
> /soc/peripheral@40000000/usbhs@144000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Now that we support internally connected channels we should make the
pinctrl configuration optional.
Signed-off-by: Corey Wharton <xodus7@cwharton.com>
Add MCO device nodes to the STM32 boards.
The set of supported boards are chosen to replace what is currently
supported in Kconfig.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Add clock sources that can be output by the MCO on the stm32f1x and
stm32f10 connectivity line devices.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Add board support for eval board ganymed_bob, which
is a break-out-board for both soc variants.
Variants of the soc are GBM and GEN1.
Signed-off-by: Sven Ginka <s.ginka@sensry.de>
Indicate in the STM32WB0 power controller binding that the SMPS output
current limitation is a feature only available on STM32WB05 and STM32WB09.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
`-` is preferred over `_` in devicetree property names.
Since, change `clk_src`, `clk_div`, and `clk_out_div` to
`clk-src`, `clk-div`, and `clk-out-div`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
There is an issue on the SHI hardware peripheral to detect CS
rising/failing with bits CSnFE/CSnRE in the EVSTAT2 register in
npcx9m7fb chip. This commit workarounds it by using MIWU to detect the
CS rising and failing.
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
The internal flash size of npcx9m7fb is 512KB. Reduce the default
Code RAM size from 320KB to 256KB because the Code RAM size is limited
by FLASH_SIZE/2 in the Chromebook EC application.
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Add common default flash partition layout for nrf52840 as many boards
have used identical flash layouts.
The default flash layout was updated to remove scrach in 2022 (9a84258)
but almost all boards were still using the previous layout, so this
updates them to the new layout with allows for larger applications.
This commit also incorporates feeedback from @nordicjm in PR #77791 to
change slot0 to 0x00077000 and slot1 to 0x00075000: "If you use swap
using move, you need a sector for the data to be moved up by, and you
need space for the swap status fields, which is about a sector, so by
making the changes here you get the full 0x65000 for an image, without
these changes you get 0x64000.
Signed-off-by: Jacob Winther <jacob@9.nz>
Adds Device Tree include files for all MCUs in the STM32WB0 series.
These DTSI files only contain the supported peripherals for now.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add timer instance in device tree
Add timer yaml file
Timer0/1/2/3 are common for MAX32xxx MCUs
MAX32655 has additional Timer4/5 which are low power timers
Co-authored-by: Mert Vatansever <mert.vatansever@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Add information to the device tree if UARTE instance has a HW feature
which is the ENDTX_STOPTX short.
Add this property to all instances in nrf54hl15, nrf54l20, nrf9280
and nrf54h20.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
we have four i2C peripherals .
- three shared between stm32u031/73/83
- One between stm32u073/83
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
There are numbers of drivers for different PCA(L) series chip. They
share similiar register layout and control logic. This driver intends
to unify these drivers for PCA(L)xxxx series i2c gpio expanders.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Implement an option manual reset of the PCAL64XXA to allow the external
implementation of a retention of the port expander state.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Adds a new DTS prop for i3c devices as support for the CCC SETAASA
requires prior knowledge of the target if it supports it according
to i3c spec v1.1.1 section 5.19.3.23.
This will be used as an optimization for bus initialization.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Set a default value for constant-charge-voltage-max-microvolt, matching
the device hardware default, this ensure compatibility with existing
applications that did not specify the recently introduced property.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add general purpose partition tables to prevent
putting copied version of the same table into the
every ESP32 board dts.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Add all the necessary files to add apds9253 Avago sensor driver.
Sensor available at https://docs.broadcom.com/doc/APDS-9253-001-DS
Signed-off-by: Margherita Milani <margherita.milani@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
This reverts commit 518de763a6.
This commit switched nrf5340 devices to use the icbmsg
IPC backend.
Unfortunately this backend is not currently supported
in the nrf5340bsim target (it is not properly configured)
which results in a segfault during its initialization.
As this issue is currently blocking CI for all BT development
in Zephyr, let's revert this provisionally while we add
support for it.
See
https://github.com/zephyrproject-rtos/zephyr/issues/78099
for more info.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
